Fixing ALL THE THINGS! - Case 1845c Hydraulic Cylinder Rebuild

Рет қаралды 38,270

4 жыл бұрын

The chickens get moved again! They are almost at the end of the fencing so this will be the last move and the fence with get moved next time. Also, the hydraulic cylinder on the Case 1845c got fixed! Things are moving along!
Things in this video (affiliate):
- Case 1845c seal kit (Bucket cylinder) - amzn.to/2MWviro
- Seal Twistor Tool - amzn.to/2NpeF6t
Related videos to check out:
- Time to GET IT DONE! - kzfaq.info/get/bejne/eNGTmM-UxKzZlWw.html
- Our chickens moved onto GREENER PASTURES - kzfaq.info/get/bejne/nNKWmLF5rcu7cZs.html
Music in this video:
- Your Love by Ben Winwood - artlist.io/song/2181/your-love
A little about us:
In September 2015, our hearts were hijacked with the dream of living on a large farm, with community, growing food, caring for animals and loving on children in need of care and healing. It was a God moment, where our dreams collided with His dreams… a dream so big we could never do it in our own strength and wisdom. Since then, we have been on a journey to see that dream become a reality. This channel documents that journey.
Instagram - goshenfarmandgardens
Facebook - goshenfarmandgardens
Website - goshenfarmandgardens.org

Пікірлер: 34

@adambauman8044 4 жыл бұрын

He starts actually working on the cylinder at 7:55.

@goldtinkerer 3 жыл бұрын

Don't forget to remove the locking set screw before attempting to unscrew the gland from the cylinder.

@keith1535 9 ай бұрын

Thanks, you gave me the confidence to tackle my cylinder. Best Keith

@GoshenFarmandGardens 9 ай бұрын

💪

@hollymorrison7793 4 жыл бұрын

Jack of all trades...& Diligent

@mattpingel7742 2 жыл бұрын

Great video!! Thanks

@southernyankee1519 4 жыл бұрын

Great video thanks

@GoshenFarmandGardens 4 жыл бұрын

You're welcome, thanks for stopping in!

@fredolygrigs Жыл бұрын

they make air tools that are much stronger if you move up to 3/4 or 1 inch drive

@hawaiiansunrise8984 Күн бұрын

You can just use AW 68 hydraulic fluid, it's cheaper and totally fine from what most guys say on KZfaq

@VolvoGonzo 4 жыл бұрын

It looks like from the foliage that you made it through the winter and fixed it in the spring? How are you able to get by with it being down so long?

@davek6630 2 жыл бұрын

I’m not sure if I would use a synthetic blend of oil. It calls for 10/30 and that case additive. Though I was told that JD hytrans fluid meets the specs

@Bubba54321 3 жыл бұрын

It's called a zirk fitting that was missing.

@johndalton9907 3 жыл бұрын

How did you get the ram off the machine? I can't see how it comes off.

@DumbCarGuy 3 жыл бұрын

you should move to MN

@peterboissiere9684 4 жыл бұрын

I have a harbor freight 3/4 breaker bar that would remove the bolt.

@GoshenFarmandGardens 4 жыл бұрын

Unfortunately I couldn't use a breaker bar because I was already afraid of bending the Piston.

@peterboissiere9684 4 жыл бұрын

Wow, I don't think u would twist the piston

@GoshenFarmandGardens 4 жыл бұрын

You're probably right. I tend to over think things 😂

@larryantoine8490 4 жыл бұрын

Wish I would've seen how you put them on.

@GoshenFarmandGardens 4 жыл бұрын

I can help answer any questions if you’re stuck.

@larryantoine8490 4 жыл бұрын

Just wanted to see what tools you used. And if I scratched the surface would is cause a problem?

@GoshenFarmandGardens 4 жыл бұрын

I used just a pair of channel locks to unscrew the cylinder cap, pulled the position out and used little screwdrivers and picks to get the seals put. Then of course the seal twister kit to get them back in. Yes you don’t want to damage or mar the piston it will cause problems for your new seals later as they run against it.

@leewehrhan3800 Жыл бұрын

It would have been nice to see how you actually install the seals. You only show after it has been installed. This is not very helpful to someone who has never done it before.