Fixing Mercedes W163 part 3

Fixing Mercedes W163 part 3 - Rear suspension

Рет қаралды 25,351

Жыл бұрын

Notice: In this video I install the rear sway bar upside down (that long bar which goes from one side of the car to the other).
The rear suspension got a major restoration. Only original parts there are now the lower control arms, their inner bushings and drive shafts. Basically everything else is new.
List of parts etc. used in this video:
- Some CRC Rust Remover
- Some CRC Galvacolor paint
- Some "AT" brand Inner Cavity Rustproofing stuff
- Lower control arm bolts and nuts (VW N 10742901 Hex collared bolt M14X1,5X120X90 + Hexagon collar nut N 10401801) 37€
- Rear shock absorbers Optimal A-3405G ~165€
- Rear springs Monroe SP3691 2x56,27€ = 112,54€
- Upper control arm rear left TEKNOROT M-814 56,06€
- Upper control arm rear right TEKNOROT M-813 53,94€
- Upper control arm bolt/nut kit LEMFÖRDER 38114 01 2x5,26€ = 10,52€
- Lower ball joint installation tool SIDEM R10093 8,95€
- Lower ball joint JP GROUP 1350250100 2x13,17€ = 26,34€
- Wheel bearing kit FAG 713 6677 40 2x29,10€ = 58,2€
- Toe adjustment bar rear left FEBI BILSTEIN 46259 50,75€
- Toe adjustment bar rear right FEBI BILSTEIN 46260 61,79€
- Rear toe adjustment bolt kit (eccentric) Febest 1629-163-KIT 2x45€ = ~90€
- Rear sway bar bushings TOPRAN 401 698 2x4,28€ = 8,56€
- Rear sway bar drop links TRW JTS981 2x13,26€ = 26,51€
Total ~790€
Total cost of the project so far ~1117€
This 2005 Mercedes-Benz ML 270 CDI (W163) was our family car and daily driver for a couple of years in 2019-2021. It is currently undergoing major repairs to be roadworthy again and I will probably use it as my daily driver when it's ready.

Пікірлер: 30

@lssamabu3427 Жыл бұрын

Professional work, thank you 👍

@ccrepairchannel Жыл бұрын

Thanks!

@grzech103 Жыл бұрын

Dobra robota! Pozdrawiam ML W163 Club Poland

@ccrepairchannel Жыл бұрын

Thanks!

@grzech103 Жыл бұрын

@@ccrepairchannel And I'm waiting for more movies :-)

@yerzhankadirbayev7153 Жыл бұрын

Hi! Good job 👍

@ccrepairchannel Жыл бұрын

Thanks!

@yaturik Жыл бұрын

nice

@handsonping 5 ай бұрын

May I ask what the torque of the drive shaft and lock is?

@ccrepairchannel 5 ай бұрын

Drive shaft nut torque is 490 Nm

@kosmosoff Жыл бұрын

👍

@CLVannoy Жыл бұрын

What are you using to treat the corrosion?

@ccrepairchannel Жыл бұрын

Sandblasting, phosphoric acid (CRC Rust Remover, Dinitrol Annitrol), citric acid, CRC Galvacolor paint, different inner cavity wax and underbody guard products. And grease (basic or mos2, whatever I happen to have around), especially for threads.

@CLVannoy Жыл бұрын

@@ccrepairchannel thank you for sharing great work by the way keep it up!!

@doriankolus2931 Жыл бұрын

Kiedy nastepny odcinek? 😃

@ccrepairchannel Жыл бұрын

Next up is the episode of putting rear brakes together, editing takes ~1-2 weeks probably…

@user-zz5mp8ro6l 9 ай бұрын

Приветствую всех,можеьт кто подскажет как меняется задний верхний шаровой,сколько не смотрю только нижний показывают ?!

@ccrepairchannel 9 ай бұрын

Hello! The upper ball joints are pressed in the upper wishbones, it is not possible to change them separately. You have to change the whole wishbone if the ball joint is worn.

@user-zz5mp8ro6l 9 ай бұрын

Привет,я правильно понял что меняется полностью рычаг целиком ?

@ccrepairchannel 9 ай бұрын

@@user-zz5mp8ro6lYes, entire upper arm must be changed

@user-zz5mp8ro6l 9 ай бұрын

Доброго здоровья! Подскажите у меня несколько проблем появилось,1) Меняли стекло лобовое ,так как резинка пошла волной сверху и протекала,вроде всё было хорошо но на днях заметил что с правой стороны пол мокрый,капает прям видно и видно что по стеклу стекает снутри стороны,думаю под резинку попадает в правой верней части,не подскажете что могу сделать,сервисов никаких нет где живу и поехать вариантов нет ?! 2) Оборвало чашку на опоре стойки амортизатора теперь надо менять опору правда не дёшево стоит одна опора ,если сниму и заварю сваркой будет толк или всё таки менять ? 3) Электроника глючит иногда,включаю зажигание пишет старт ерор и стартер никак не реагирует,несколько раз включаю выключаю пропадает и запускается,ещё было еду просто перестаёт работать газ остановился работает на холостом и всё ,заглушил и сразу запустил поехала,просто не пойму куда надо залезти и что делать,что проверить или поменять ! Вот такие проблемы появились буду очень блогодарен если что подскажите !🙏

@ccrepairchannel 9 ай бұрын

@@user-zz5mp8ro6l1) You should take the car back to the shop and ask them to fix it properly. Temporarily put some tape on the edges of the windshield. 2) What model is your car? I have never replaced strut mounts on chassis, on some models they should be riveted and on others welded. 3) Starter motor or starter relay? - Relay is very cheap and easy, starter motor a bit more expensive and on some models quite difficult to replace.

@PatrickStar-qb1sx Жыл бұрын

3 little nuts from top of the rear shocks are not easy to remove. please make longer videos and show all the steps next time. Thank you!

@ccrepairchannel Жыл бұрын

Luckily they weren’t stuck in my car… Some parts of this W163 project were filmed in such a bad quality camera, that I decided not to use all of the video material. But nowadays I film with a more decent camera (iPhone se 2020 😅)… So I try to include all the parts of the process.

@alfredonycmeneses2669 5 ай бұрын

Remove the donut tire fron underneath

@TheEscape2012 3 күн бұрын

what about brushing off the rust and puttung on some K-line rost stop primer? You did nothing! The car will be off the road in a few years with that rust.