Fixing my Oil Burning Mercedes

Рет қаралды 44,377

Жыл бұрын

Replacing Valve Stem Seals on my W211 Mercedes E500
My 2006 Mercedes E500 was suffering from excessive oil consumption. Upon further inspection, I noticed the valve cover gaskets were leaking. I was also able to diagnose bad valve stem seals due to the blue smoke occurring after idling for a while. Simply blipping the throttle after a few mins of idling would send a big cloud of smoke in the air… and I mean BIG. Replacing the valve stem seals fixed that issue and my oil burning woes are over. During reassembly I also slapped on some new valve cover gaskets which fixed my oil leaking issues as well.
This repair should work for any M112 or M113 engine, as they are essentially the same engine with +/- 2 cylinders.
Do this repair at your own risk. Good luck!
I’ll be monitoring comments for any questions!
List of M113 Cars:
1997-2000 C 43 AMG
1997-2002 E 430
1998-2003 CLK 430
1999-2001 ML 430
1999-2006 S 430
1998-2008 G 500
1999-2006 S 500
1999-2006 SL 500
2000-2006 CL 500
2001-2008 ML 500
2002-2006 CLK 500
2002-2006 E 500
2004-2006 CLS 500
2006-2007 R 500
1997-2000 C 55 AMG
1998-2001 SL 55 AMG
1998-2002 E 55 AMG
2000-2002 S 55 AMG
2000-2003 ML 55 AMG
2000-2003 CLK 55 AMG
2002-2006 CLK 55 AMG
2001-2002 CL 55 AMG
1999-2003 G 55 AMG
2004-2010 SLK 55 AMG
2006-2008 SLK 55 AMG Black Series
2005-2007 C 55 AMG
2003-2006 CL 55 AMG
2002-2006 S 55 AMG
2002-2008 SL 55 AMG
2003-2006 E 55 AMG
2004-2006 CLK DTM AMG
2004-2011 G 55 AMG
2004-2006 CLS 55 AMG
M112 Cars:
1996-2000 W202 C 240
1998-2000 W210 E 240
2000-2005 W203 C 240
2000-2002 W210 E 240
2003-2005 W211 E 240
2002-2005 C209 CLK 240
1998-2000 W202 C 280
1998-2006 W220 S 280
1998-2001 R129 SL 280
1998-2002 W210 E 280
2000-2005 C 320
1998-2005 E 320
1997-2006 G 320
1998-2002 S 320
1998-2003 ML 320
1998-2001 SL 320
2000-2003 SLK 320
1998-2005 CLK 320
2001-2003 C 32 AMG
2001-2003 SLK 32 AMG

Пікірлер: 97

@LynxStarAuto 11 ай бұрын

You mentioned something in this video which is very underrated, and an old mechanic's trick that was passed on down to me from my dad: the use of rope. I learned to stuff the cylinder with nylon rope, and I never used air ever again. Air sucks as you saw in this video. Too many variables fighting you. Whether it's a tiny leak somewhere, your equipment that can't keep up, the engine wanting to spin on you, or as what happened to you here, the entire valve and spring assembly compressing because the keepers are stuck from the years. Rope makes life much easier for you, and it's cheaper! I been doing this 21 years now, and it's my go to method.

@beeswax7825 2 ай бұрын

How do you feed the rope in ? Got any tips

@havocshots2k Ай бұрын

Dude you are sooooo knowledgeable and not only that but, you are so patient on explaining it’s right on the money 💪🏻 I have to give you an A+. Actually with a million ++++++++++++++++ signs Great job done and thank you for helping me and most definitely others as well! 💪🏻💪🏻💪🏻💪🏻💯

@carubplayz7883 Жыл бұрын

Mercedes are such nice cars

@r.weaver3769 11 ай бұрын

I was taught to rotate the cylinder your working on to top center, apply air pressure. Than way if a valve loses seal it cannot fall into cylinder as the piston itself will block it. As a safety precaution. Outside of that, most informative video, and second replacing all rubber hoses, it's not they may break, they will.

@Parklc13 8 ай бұрын

Did You fixed cranshaft at the other end?

@r.weaver3769 8 ай бұрын

@@Parklc13 I'm not understanding the question.

@typetbg 9 ай бұрын

just did mine on a 2006 ML 500 with the m113 engine, absolutely no need to mess with ropes or air compressors, just make sure you rotate each piston to TDC while changing the seals. I used a thick cable tie inserted in the spark plug hole to check for TDC. Once you do this, the valves can only go in like 1-2 cm before contacting the piston and the valve stem sticks out at least 2-3 cm, zero chance to drop it inside the cylinder. It's very important to hammer the tops of the valves to loosen the keepers before you remove them, they tend to be kinda stuck and reduce the chance to bend the valve while pressing the spring to remove the keepers.

@67vala 7 ай бұрын

@typetbgcan can I contact you somehow please? Tomorrow i want to do my valve stems seals :)

@tooththrhr 2 ай бұрын

1cm of valve to piston clearance ??? I dunno.man

@antoniyantonov910 Күн бұрын

@typetbg If you are Bulgaria, let's get together to do it for my m113, ofc will pay for that.

@TheoSmith249 9 ай бұрын

this video, along with the accompanying comments has given me the confidence to tackle this job. Many thanks- KZfaq at its best.

@markymark5375 8 ай бұрын

Excellent video.. There's no way I could have done it without watching this. The first two seals were kind of spooky because I knew if the valve fell into the cylinder I was doomed. But after the first few I gained some confidence and it wasn't that bad. I hooked up my air compressor and it went fairly smoothly. I put shop towels all around all the openings in the head cuz I'm the type who would drop one of the keepers in one of the holes and spend 1/2 the day looking for it.. Finally that last exhaust valve, there was no way my particular tool would fit and I could do it properly. The top of the spring compressor tool would hit the heat shield and I could NOT angle it properly. I finally just cut the compressor tool in 1/2 with an angle grinder. Then it fit perfectly.. Of course it makes doing the intake valves impossible in the future, but for $50 I can get another kit. Better than spending thousands if I drop the exhaust valve into the cylinder.

@julesviolin 4 ай бұрын

Put the piston you're working on at TDC, that way the valve cannot fall in. In fact it will only fall a couple of mm even without rope or compressed air 😉

@MercTribe 11 ай бұрын

Wonderful job. Clear and detailed.

@revinot 11 ай бұрын

thank you, you made it look so easy, and thanks for showing the tools to use for this job.

@JohnsJohnson-ns5xm 8 ай бұрын

Very well-made video thank you I’ve got the S 55 AMG and I imagine I’ll be doing this in the near future

@N-e.o 2 ай бұрын

Bought the exact same kit. Gonna do this next week myself😊

@RNN24 11 ай бұрын

Informative, educational, yet entertaining! I really enjoy it.Thanks for sharing!

@OnlyKelp 11 ай бұрын

Thank you!

@derekdominguez9793 11 ай бұрын

Very thorough video thank you!

@xXHakunoXx Ай бұрын

Your engine looks very healthy from the inside mine is like almost complete black.

@L35inColorado 6 ай бұрын

Great video! Thanks for posting this : )

@Leonardo555ZZZ 11 ай бұрын

Good work.

@dagurorarinsson2827 8 ай бұрын

Great video! But i have to say that the camshaft bridge bolts are 1 time use torque to yield bolts

@theinsaneshecklador6598 2 ай бұрын

He mentions that in the video.

@chouaibelberhami9940 Жыл бұрын

Thank You for the Video, i also wanted to do it on my w211 M112 engine but I was afraid that the valves will fall. Now that I see you doing it, I might have the confidence I can do it too 😊

@OnlyKelp Жыл бұрын

I used 85psi on my air compressor to keep the valves up. Some people say that’s too much, others say they use more. 85psi worked great for me though. Another method you can try is feeding rope through the spark plug hole and turning the engine until the piston presses the rope against the valves if you don’t have a compressor. Either way will work. Good luck!

@shapnasohail874 4 ай бұрын

Nice job 🎉

@thelongranger55 9 ай бұрын

Cool video , I need to do head gasket on my w163 ml500 m113 , & I plan on doing this while the heads are off . It would be a good time to do the dreaded 2 timing cover o-rings Edit : head gasket never blew it was the timing cover O-rings that failed !

@adventurousairman 9 ай бұрын

Great job!!

@jianliu7516 Ай бұрын

I m doing same job on my car today use the same tools, my 2005 E500 burned a lot of oil for years. it is easy for upper stems but very difficult for bottom inner stems because the tool too long won't fit to remove the bottom inner springs. Your video only showed the easy part but skip the difficult part. But still good video anyway.

@broken55muffler31 3 ай бұрын

This is crazy! Cool technique! Gonna have to try it! And to guy mentioned turning cyl thats Pretty cool saved me taking off the heads.. if compression is good on my engine ill try this burning oil i have 221k miles. Thanks bro.

@rtap8170 8 ай бұрын

100% agree with you on going genuine Mercedes valve cover gasket. I believe fcp used to use elring gaskets, and I had the same thing happen as you with fcp’s kit (which they have since changed to have factory gaskets). The elring ones leaked immediately. No leaks since having the factory ones!

@OnlyKelp 8 ай бұрын

Correct. FCP hasn’t sold that brand for a while I believe but I had bought a set while they were still being sold and they leaked not that long after. The genuine Mercedes ones aren’t that much more $$$ and they won’t leak. Not for a while anyways 😆. Luckily they come with lifetime replacement from fcp anyways 🤷‍♂️

@mikeedeep3518 7 ай бұрын

very nice video very professionnal hope you could do one about the head gasket 🙏🏻😅

@dannoi 11 ай бұрын

Good job ! appreciate the very detailed video too ) but you should def reseal the breather covers as you mentioned towards the end, and it sure would have been easier with the cover off ) those leak just as often as the big covers

@OnlyKelp 11 ай бұрын

I just did the breathers a couple days ago. I noticed a bit of smoke from the exhaust at high rpm which prompted me to check them. Once I took the breathers off I noticed the little pinhole where the air is supposed to come out of was blocked by a bit of sludge in the breather chamber. Whatever car the new valve covers came from must not have been cared for all that well. I cleaned the inside of the valve cover and got any sludge and debris out and reinstalled them on the car. No more smoke!

@dannoi 11 ай бұрын

@@OnlyKelp ya with age they all do that, so def worth pulling and cleaning )

@igornikonov3187 9 ай бұрын

Thank you very much for this video!!! I bought my e430 3 years ago (100k miles) and noted the oil consumption. I bought everything for seal repalcement including the tool you are using (and valve seals, conpressor, etc) but did not have enough confidence to proceed. Could not find videos re this job on m113. So thanks again. You noted you used 85psi? How is the oil consimption now?

@FifiRX 11 ай бұрын

Great video, thx

@garyzhang5099 11 ай бұрын

I did this on my 210 e55 last month, seems every 112/113 start to loose their valve seal now. Btw, I also use compressor on passenger side, and can’t brake the keeper on driver side, so I switched to rope method afterward. IMO, rope method works much better in my case, less noise, engine won’t turn, less stressful, and break every keeper flawlessly.

@morganblais5046 Ай бұрын

Ive found on the passenger side you cannot mount the brackets as far forward as you did on the drivers side. Wish id seen the snipe earlier as ive been trying without and it gasses you out quick without it.

@laqueenawilliams4762 10 ай бұрын

Can you please do video on transmission fluid flush? Don’t know how to reach the radiator hose.

@eatont9999 6 ай бұрын

I've done valve stem seals on other engines but the process is the same. It's not exactly what I would call fun but sometimes it is necessary. I've heard all the tricks about using rope and barring the engine over, etc. but it's a waste of time if you have at least minimal shop air. You can put a squeeze clamp on the end of the valve while you are getting parts ready if one is that paranoid. I have an 03 S430 with about 185K on it. It doesn't burn any oil past what is normal. I'm about 1qt low after 10k miles. Hopefully I don't have to do valve stem seals anytime soon.

@Parklc13 8 ай бұрын

Thx! So just a quick question. So where were you at markings at harmonic balancer? Did you changed it for each cilinder for using Air compression? Thx for the answer

@rickchowsr2532 Ай бұрын

Ethan I know this video is older but do you happen to links for everything needed to do this job? I was only able to find the valve cover gaskets pcv hoses and valve seals I’m looking for the spring compressor and the bolts that hold down the valve train TIA

@miseryparty3726 11 ай бұрын

Timing chain is beautiful after so many miles. Super clean. Was it replaced?

@OnlyKelp 11 ай бұрын

Nope, all original! The car has been in my family since 60k miles and has been serviced regularly. I’m creeping up on 300k miles too!

@raphaelandrew6631 11 ай бұрын

Do know the part number for the rockerarm bolts? Or size. Hard to find. Ty

@kingbryant5673 8 ай бұрын

This isn't a job I'm looking forward to but a job that needs to be done. After reading the description my 06 e500 is having the exact same issue

@stanislavb.5163 Ай бұрын

привет. отличное видео. я делаю такую работу в России Москва. на м113 работа занимает 2.5-3 часа . на м112 2.5 часа максимум.

@Faris85 8 ай бұрын

Hi , I have a question. What's the quantity you were losing of oil ? I'm losing around 2 litres in one month , M113K

@Stoyan.Stoyanov 9 ай бұрын

Can you tell me what amount of oil the engine was losing? Mine is a M112 3,2 and the losses are about 1 litre per 1000km.

@michaelsliwinski8044 8 ай бұрын

Nice work, thanks!

@thelongranger55 7 ай бұрын

Did you use new camshaft bridge bolts ?

@luispinto3928 2 ай бұрын

Did you also replaced the camshaft bridge with new bolt?

@james_crow2352 9 ай бұрын

Nice work man!! Im gunna do my 05 CLK55 AMG in the next couple weeks. Did you use 10 or 15 nm PLUS 90° for the valve train?

@derrickmonares3865 7 ай бұрын

Did you ever do yours? I need to do this to my CLK55 also.

@james_crow2352 7 ай бұрын

@@derrickmonares3865 not yet. I'm still waiting on a couple parts to show up that I ordered.

@AFFALTERBACHgtamods 3 ай бұрын

Did you remove the Chain tensioner or just removed the Rockerarms without removing the Chain tensioner?

@ziyadsaeid2082 7 ай бұрын

شكرا ❤❤❤

@RoCino860 25 күн бұрын

What site did you go to for bolt pattern removing and replacing it

@gikvampire5191 9 ай бұрын

Using the compressed air method the engine rotates a bit, does this hurt the timing? Do you have to do anything to the timing after doing this job considering the camshaft rotates a bit after applying pressure to the cylinder? 14:06 Thanks!

@Akadectra 4 ай бұрын

Hi. It does not hurt the timing because everything is connected by the really solid chains. No timing adjustment will be necessary. Greetings from Bavaria/Germany

@terrenceg3257 10 ай бұрын

Thanks for the video! I want to change noisy lifters. Is it hard to get them out of the rockers?

@theinsaneshecklador6598 2 ай бұрын

Tasos Moschatos has a good video on the lifters if anyone in the future has the same question. I think XF Motorsports also shows it in his E55 rebuild series.

@terrenceg3257 2 ай бұрын

Hi. Does the harmonic balancer need to be in a particular position before removing the rockers? Thanks

@rafag1194 7 ай бұрын

Im currently doing same job same tool...question: since there are two sparkplugs per cylinder does it matter which one I connect the air compressor to also do i need to cover other hole or no? Thanks

@OnlyKelp 7 ай бұрын

It doesn’t matter which whole you connect the air too. Just make sure you leave the other spark plug in unless all the air would escape

@rosewd2 9 ай бұрын

you may also want to replace the seals before and after the throttle body. those get hard and allow air and dirt by.

@OnlyKelp 9 ай бұрын

Great advice, thank you! I noticed mine looked a bit crusty last time I had taken off the intake piping

@67vala 7 ай бұрын

@@OnlyKelphello, please did you put every cylinder to top dead center and afterwards you filled it with air? Or you just put there 85psi to each cylinder, without turning the cylinders to TBD? :)

@georgeanddaddecker7563 Жыл бұрын

I recently purchased a 2003 E 500 sport from Arizona and shipped BB it to RI. 72k , no corrosion anywhere, dealer serviced,new shocks,struts,springs, rear main seal, motor mounts,crank pulley,trans svc.,new radiator,new michelins,new front brakes,mirror gaskets,and ps res. Do you have any suggestions for repairing ribbon cable to piano roof rear ligjts?

@georgeanddaddecker7563 Жыл бұрын

Sorry auto spell. I have the panoramic sunroof. The interior rear lights have broken ribbon cables, do you have any suggestions regarding repair?

@OnlyKelp Жыл бұрын

@@georgeanddaddecker7563 Unfortunately all the W211s I’ve owned have had the regular sunroof so I don’t have any experience working with panoramic sunroofs. Maybe one day!

@W210Garage 11 ай бұрын

Would be great if you show how to remove and install camshafts on 112 or 113 engine.

@OnlyKelp 11 ай бұрын

Once you get as far as I did with the tear down in this video you just have to remove one more bolt that holds the sprocket for the timing chain to the camshaft. Just make sure to put a couple zip ties around the chain/sprocket so you don’t mess up timing. Once it’s disconnected, the camshaft lifts out quite easily.

@theinsaneshecklador6598 2 ай бұрын

If you Google Kleemann camshaft installation you can find a PDF on Kleemann's website showing instructions. It's not a video though. Just pictures and words.

@W210Garage 2 ай бұрын

@@theinsaneshecklador6598 Hehe, I know that, but 1 is what is written and 2 is what have to be done in the real situation. Thank's for the tip :)

@theinsaneshecklador6598 2 ай бұрын

@@W210Garage 👍

@wiklebrun Жыл бұрын

How much torque for the rocker arms?

@Leonardo555ZZZ 11 ай бұрын

Long bolts to be replaced ,,,10Nm and then 90 degrees. Short bolts ,,15 Nm.

@wiklebrun 11 ай бұрын

@@Leonardo555ZZZ thnx

@raphaelandrew6631 11 ай бұрын

Are thoes bolts also called cylinder head to timing case bolts? Having trouble finding thoes bolts. I got the valves keepers from MB dealer, but they are not finding bolts.

@mikimiki195 18 күн бұрын

Dude you are way too relaxed doing this job. I just did valve seals on my BMW N63 engine I was hard job. But I got it done. FYI anyone trying to do this job just be careful do not push down on the valve if you drop valve down you are royalty Fucked Good video tho

@W210Garage 10 ай бұрын

Did you replace the rocker bearing bolts? I am a little confused. Can you tell in overall how many bolts do i have to need? I'm going to replace Camshafts and can't understand in overall how many bolts and which ones have i need to replace. Engine M113. EPC shows different part numbers...

@MackhackCA 9 ай бұрын

I have complete kits for sale. All OEM parts, up to 75% discounted directly from Mercedes.

@W210Garage 9 ай бұрын

@@MackhackCA Have ordered from MB totally 38 bolts.

@dalemartin684 8 ай бұрын

So you have complete kits to do this valve stem seal replacement? OK, if so lets talk. I need all necessary items (seals, bolts) for my 2006 CLK500.@@MackhackCA

@MackhackCA 8 ай бұрын

@@dalemartin684Yes I do.

@jedi-mic 4 күн бұрын

You can just use a valve remove tool you don't need to buy that device

@bigthecat1808 6 ай бұрын

Did this fix your oil consumption issue?

@OnlyKelp 6 ай бұрын

For the most part yes, although I still have some blue smoke coming from the exhaust above 4,500rpm. Luckily I'm not at that rpm very often. I suspect I have a few sticking piston rings.