Thanks for sharing this. I was using the SCAL 5 hack, but it cuts way too fast for how floppy these machines are. It was literally cutting dashed lines on the Y axis (or is that z on a vinyl cutter). I'm looking forward to proper speed control. FYI, disassembly is not required. All the pins are accessible through the cartridge port. Get a proto board with edge connections and some basic soldering skills and you're golden. Pin 1-6 on the ribbon cable are the front left edge connections. The first connection is pin 1. It's even reversible (back right pin is also pin 1). I'm going to try this on my junky expression that I already have torn apart. If it works well, I'll do it to my nice one. Yes, I have a goodwill computer store addiction problem that resulted in my ownership of 3 cricuts.
@ellisgl2 жыл бұрын
Have you been able to get around to building an adapter?
@generic00002 жыл бұрын
@@ellisgl No. I was going to make one to use with an Arduino as the programmer, but I couldn't get atmel studio to talk to the Arduino. I bought an avr programmer that had an adapter that would plug into the cricut's board, so I just went that route. I now a 2 expressions from goodwill running the custom firmware. Also, I got them to work with SCAL 5. I don't really like that software so I just use inkscape, but some people may want to go that route.
@ellisgl2 жыл бұрын
@@generic0000 interesting. I wonder if you can just compile the hex and use AVRDude to load it up?
@generic00002 жыл бұрын
@@ellisgl I did try to do that, but I'm completely lost with atmel studio. If I remember correctly, I couldn't figure out how to get the hex file. Sometimes it's hard to find out how to do simple things in technical software that just assumes you know what's going on. I'm familiar with Arduino IDE, but I'm kind of spoiled with things just working within the arduino (and even ESP) ecosystem. and they make their instructions simple enough that my kid's could follow along.
@ellisgl2 жыл бұрын
@@generic0000 I'm wondering if Visual Studio might be able to do it with PlatForm IO instead of atmels huge dev env
@kevinrak27763 жыл бұрын
For pressure and speed: Pressure: press Xtra1, then press the +/- arrows, then press load/unload paper. Speed: press Xtra2, then press the +/- arrows, then press load/unload paper. Great video! Managed to do this using an Arduino instead of a dedicated ISP device. Thanks!
@coolguybob8 ай бұрын
I press Xtra1 and then + and bunch of times and still the pressure is not deep enough to cut. My cutter setting is also at 6. Any suggestions?
@thegreenysgarden Жыл бұрын
I was thinking why doesn't he use a magnet for catching the screws... then giggled when you did. Thank you so much for this video! I'm going to work on this tomorrow 😁
@krisr84423 жыл бұрын
Thanks for taking the time to make this!
@ghostboi8172 жыл бұрын
Thank you for this I would have been so lost without your video
@DC-wm7jl3 жыл бұрын
Thanks for this video! It's good to see the firmware in action since there's not a ton of info on free expression out there and it is a one way street. Im very much looking towards flashing the one I found at a garage sale this morning!
@NVRMTmotion2 жыл бұрын
Did you manage to get it flashed and working?
@kennyking6325 Жыл бұрын
Friends, I am going to try this on a cricut create crv20001 fingers crossed. The processor is the same and most buttons are similar… Thank you
@rosariomonts4339 Жыл бұрын
Any update on this?
@thurlravenscroft25723 жыл бұрын
Will this work with the original Cricut. It looks similar.
@thurlravenscroft2572Ай бұрын
Trying this on my Mac and it works until the last few bits of any design, then the knife stays down and it feeds continually 🤷♀
@eeledahc2 жыл бұрын
I bought one of these the other day hoping that I could use it to cut out stickers that I printed on my regular inkjet printer. Would this be a good use case for freexpression? I'd like to try it out. I have a usb/asp that I bought for putting a bootloader on my 3d printer and a ch341a and I bought for flashing bios chips. Could I use either of those?
@CrazeUK5 ай бұрын
Hey there. Is this possible to do with the Circut explore 3
@jeanyoussef42924 ай бұрын
I can not down the ist program is there an alternitive
@drmuna38494 жыл бұрын
Is there anyway to code the machine /add hardware to make it WiFi capable?
@johncabrer23282 жыл бұрын
Not easily. You would have to bypass the USB interface and wire up an ESP to the UART. Probably would not be reliable.
@TsarNateRules Жыл бұрын
Will this circumvent the blacklisted serial cricuts that are deemed scrap by them and wont fix?
@mikeag Жыл бұрын
I have been messing around with the firmware in MC/AT studio for a bit. I'm quite certain there is something wrong with the clock speed after flashing. The display is PAINFULLY slow in refreshing. the author abandoned the project a while ago after commenting out the display refreshes which is why you can't see the speed and pressure change. I am unable to as of yet isolate the problem with the selector wheels or the display. QUESTION: Do the fuse bits change on reloading the HEX? Is it possible the xtal is selected from the software after the fact? thanks
@calamityjaycantebrigge Жыл бұрын
Any ideas of a custom firmware for the original Maker that was a warranty return? I bought it from someone cheaply because I hate the WEEE waste these would otherwise become so I'm looking for a way to make it usable again.
@VVander1814 жыл бұрын
Great video what video recording software were you using to do this?
@johncabrer23282 жыл бұрын
OBS.
@joepompo3103 Жыл бұрын
Will this work on the Explore Air 2? I accidentally bought a bricked one for my daughter on fb
@mindellica2 жыл бұрын
Hello John I just found your channel on KZfaq I'm wondering if you or anyone can help my cricut is just blinking cricut on the cricut screen. It was fine this this morning and I downloaded cricut design space and it started blinking, I can't even shut it off without unplugging it. PLEASE HELP
@johncabrer23282 жыл бұрын
Hi Marie, I have never used design space, but it is possible that the program attempted to upgrade your firmware and failed. It's not common, but it does happen. There might be a way to force the Cricut into recovery mode by holding down some button on powerful, but only the manufacturer can help with this.
@colinsnyder30822 жыл бұрын
Having trouble with armed recognizing my asp controller… any tips?
@WhiteRavenMobility2 жыл бұрын
Could this be made to work with the cricut personal like the freecut firmware did?
@sebastianpaukner3682 Жыл бұрын
Is it possible to flash a cricut maker 3 ? I hope somebody can help me 😢
@DanCopelandphotography10 ай бұрын
why not 3D print an adaptor to fit the cartridge port and not take it apart
@thurlravenscroft25722 жыл бұрын
Got this working finally. Everything cuts backward though. Any thoughts?
@johncabrer23282 жыл бұрын
Are the steppers connectors flipped? This can cause the motors to turn backward.
@LucemExTenebris Жыл бұрын
At 36:40, the "Mirror X axis" and "Mirror Y axis" boxes should be checked.
Does this work with a disabled Cricut Maker? Does anyone know how to turn it back on please? Thank you
@johncabrer23282 жыл бұрын
Unfortunately no. This formware is only for the Expression. Depending on what "disabled" means, you might be able to buy another broken Maker, and swap out the bad component. See if there are any hackerspaces near you. Someone there might have the skills to assist.
@lalla542 жыл бұрын
@@johncabrer2328 Disabled remotely by Cricut to avoid return shipping costs. The Cricut Maker is new and considering the price I find it a shame not to be able to find a solution to use it. Unfortunately I don't know anyone here who could help me as the brand is recent in France. I think it must be possible to reactivate it remotely but I don't know who would be able to succeed
@johncabrer23282 жыл бұрын
That type of disable permanently burns fuses in the chip and is not reversible. The microcontroller would need to be swapped out.
@lalla542 жыл бұрын
@@johncabrer2328 can we talk in private please? Can you explain to me what you think exactly what it is and what to do?
@lalla542 жыл бұрын
@@johncabrer2328 Can we talk in private please 🙏🏾🙏🏾? Can you explain to me what you think exactly what it is and what to do?
@3nginuur3 жыл бұрын
will this work on a cricut air?
@johncabrer23282 жыл бұрын
No.
@luckybones78082 жыл бұрын
So, all the cricut cartridges are just blank? Damn... I'll need to look up your other video
@johncabrer23282 жыл бұрын
Only the cart that comes with your machine in the box is a placebo. The fonts for that one are stored in flash.
@luckybones78082 жыл бұрын
@@johncabrer2328 wow, thank you for answering! I figured this model would be easier to hack since it was one of the first ones to come out
@Multiplemom34523 жыл бұрын
Wonder if you can do this with the Cricut imagine.
@johncabrer23282 жыл бұрын
No.
@Multiplemom34522 жыл бұрын
@@johncabrer2328 bummer oh well what can ya do when ya live in a shoe? Lol.
@mindellica2 жыл бұрын
It's a expression 2
@karenpowers35913 жыл бұрын
Friend was ripped off with purchase thru Facebook and waited a year to look, she's got expression 2 not explorer 2, will this work for it, the scale won't work for this machine
@fickitonetime3 жыл бұрын
Also interested to know if Expression 2 is supported by the firmware. Thx
@johncabrer23282 жыл бұрын
As far as I know it only supports the original expression.