Flexible Hoses SolidWorks 2021 Tutorial! Swept Boss/Base Command step by step!

No video

Flexible Hoses SolidWorks 2021 Tutorial! Swept Boss/Base Command step by step!

Рет қаралды 27,275

Күн бұрын

Hello friends, and welcome back on my channel, in this video I am making another easy part for beginners step by step, I hope I am helping you with this videos to learn SolidWorks faster! If you have any parts like this and you want a tutorial about them, leave a comment, and I will answer you as fast as I can :D
Thank you for watching, and I hope to see you in the next videooo :D see you!
And if you want to support me, you can leave a like/share or subscribe :D
Here is my Facebook page where I am posting some of the drawings that I am using for my videos :) I will try to upload drawings every Sunday for the previous week. #SolidWorks #CAD #HoleWizard
/ alexs-engineering-1146...
Sharing is Caring, any support is welcome www.tipeeestre...
-How to activate "Dynamic mirror entities" see in this Tutorial:
• SolidWorks Double Bear...
-How to limit Movement in Assembly:
• How to LIMIT the MOVEM...
-How to make a MOLD:
• How to make a MOLD in ...
-How to use BELT/CHAIN command:
• How to use BELT/CHAIN ...
-How to make EXPLODE VIEW:
• Explode View!! SolidWo...
-How to use AUTOTARCE :
• How to use AUTOTRACE t...
-How to Engrave a Picture on a Sphere:
• How to ENGRAVE a PICTU...
-Tips & Tricks SolidWorks: • SolidWorks Tips & Tricks

Пікірлер: 24

@irfanyusuf3992 2 жыл бұрын

why i cant make it tangent to the temporary axisZ?

@Welightonejessica 3 жыл бұрын

Nice job, congrats.

@AlexsEngineering 3 жыл бұрын

Thank you 🤗

@joeyqueen9094 4 ай бұрын

I keep getting an "over defined" message when I try to make the spline tangent. Does the whole assembly need to be locked?

@AlexsEngineering 2 ай бұрын

it depends what assembly you have, in my case I have some moving parts which are not locked. So try to delete some constraints from the spline line to make it more flexible

@subashniraula4443 2 ай бұрын

Hello, I am using this same way to make piping for hot tub. But my problem is that the pipe is not hollow inside. Is yours hollow? any suggestions? Thanks.

@AlexsEngineering 2 ай бұрын

yes it is hollow inside, if you look at minute 2:40 you can see that is hollow inside, just follow the tutorial and your hose will be also hollow

@qozia1370 6 ай бұрын

Thanks!

@AlexsEngineering 6 ай бұрын

Welcome!

@chauhanmanish4381 Жыл бұрын

Thanks brother

@AlexsEngineering Жыл бұрын

You're welcome

@ravinderkumar526 5 ай бұрын

please make a wire braiding video

@w.binder-freecadchannel 3 жыл бұрын

Vera nice👍😀

@AlexsEngineering 3 жыл бұрын

Thank you 🤗

@bollywoodsongs3490 3 ай бұрын

Good

@AlexsEngineering 3 ай бұрын

Thanks

@cheenu_ 7 ай бұрын

I cant able to select the path

@PedroRodrigues-rj8hu Жыл бұрын

great!!

@AlexsEngineering Жыл бұрын

Thank you 🤗

@alexanderj4545 2 жыл бұрын

Do you know why I can´t get the end of the spline (2:00) to mate with the centerline...

@AlexsEngineering 2 жыл бұрын

I don't know, have you tried again? try again and follow the steps in the video, it should work

@sverre1990 2 жыл бұрын

I had the same problem, but found a work around. Do everything up until point (2:00), then make a axis in your new hose part in each of the two locations, and use those axis' to make the spline tangent. I was not able to use the temporary axis' as Alex did.

@damgnj 2 жыл бұрын

Go to the System Options - General, then External References, and check boxes of "Automatically genetate names for reference geometry" and "Allow creation references external to the model"