Mistakes to AVOID when Building Your Garage or Metal Building

Рет қаралды 94,426

Жыл бұрын

PA Garage Build series: • PA Garage Build Series
List of things I regularly use :
Front Track Brake Pads Hawk DTC-60: amzn.to/4aCOoLA
Front Track Brake Pads Hawk DTC-70 (more aggressive): amzn.to/4aMSEHn
Rear Track Brake Pads Hawk DTC-30: amzn.to/3JmljYF
GearWrench Socket set I've used for YEARS: amzn.to/3wW9q9d
Deep and Standard Sockets: amzn.to/4c0vkHe
Castrol SRF brake fluid : amzn.to/3Ukmxdb
Motive Brake Bleeder: amzn.to/446kH38
Motive Honda Adapter:amzn.to/3Uw1AMN
Air hose for Motive Bleeder: www.harborfreight.com/3-ft-x-...
Allen Wrench set: amzn.to/4dYkqnh
Wheel Protector Impact Socket set: amzn.to/4bDYQmn
Brake Bleed bottle: amzn.to/4aSYcR6
Radar Detector Mount Cable: amzn.to/3xMULx4
Radar Detector Mount Bracket for Uniden: amzn.to/4aJCyzq
Autel MD 806 Pro - amzn.to/452TNte
Best Jumper Battery: amzn.to/3wunKRa
Recommended Transmission Fluid: amzn.to/2D7XBkx
DEI Exhaust Wrap: amzn.to/3bK5LMC
After building an 18x21 carport, I decided it was time to roll up my sleeves and take on a HUGE garage building project. In this series, I take what was an unused piece of mostly virgin woods, and turn it into a level 30x50 garage that is going to be used as a car shop. You'll see me tear down a lot of trees, pull up tree stumps, get over 100 truckloads of dirt delivered, over 100 tons of gravel and rip rap delivered, buying and using a plate compactor, putting up concrete forms, pouring the concrete, sealing the concrete and eventually, putting up my custom metal garage building. All the while, using my Kubota SVL75-2 and various attachments (Virnig grapple, Titan backhoe etc..) to conquer the land.
Email me at realflyingato@gmail.com
Follow me on Instagram @FlyinGato
Follow me on Facebook @FlyinGato

Пікірлер: 58

@idonwantella2824 6 ай бұрын

there are magnets you can attach to the metal posts that have an eyelet that lets you use zip ties. No drilling, they are very strong and you can move them.

@kookiethebear Жыл бұрын

Looks good. If someone else tries to install a lift where you planned it will be a chore having to deal with all that rebar and mesh with a drill bit.

@ytorwoody 7 ай бұрын

I got a Carolina Carports building also and am happy with it, except for one thing. They didn't ask about the flute direction for the roof and since this was my first metal building, I didn't know to ask. Had they asked, I'd have definitely chosen to have them run in the same direction as the trusses run. When the assemblers started laying down the roof metal, I was sick. I knew that I was going to be seeing leaks. I simply had to hope that there wouldn't be a lot of them. It works, but it would have worked perfectly had they just asked

@J297WFD 5 ай бұрын

You have some good ideas. I like it. I just built a 24x36 ranch style garage 2x4x8 with roof trusses ( attic space but no storage ). It’s insulated with R 15 rock wool for the walls and I had R 39 blown in the attic . The interior walls are plain ship lap with primed pine trim around the doors and windows. I did go nuts and gave it its own electrical 200 amp electrical service. A 24K btu mini split with heat pump ( works great ). The foundation is a frost wall that is about 12 inches above the slab giving me 9 foot ceiling. Two garage doors are on the gable end wall with my shop at the far end. I do mostly woodworking so it’s set up for that. The floor slopes from the back to the front doors and the pitch is roughly 3 inches from the back to front. I wasn’t sure if it was too much when they poured it but now I can say it works great and you don’t notice the slope. I don’t know what the pros say but I think 1 inch per 10-12 feet is a good number.honestly 3 inch slope spread out over 40 or 60 feet would probably work. It wasn’t cheap! Steel is cheaper. I built it myself but I subbed out the roof,minisplit,electric. Not counting the site work the materials cost around 15k with everything I think I’m at 40 k the electrical required trenching about 150 feet the concrete work was 9k the dirt work was 13k I had a lot to do. Anyways I learned a lot and if I ever build another I agree with you build it as big as you can.

@shanerogers488 5 ай бұрын

Great video man! Thanks so much! Loved the “if I had it to do over again…” comments. Those were the most helpful to me.

@loganhubbard3177 Жыл бұрын

Hey I built a similar structure, and I installed auto opener on the roll up doors.

@SciaticaDrums Жыл бұрын

I would definitely have gone with proper garage doors. I had a 30x40' post framing style garage done and I love it. Automatic openers are a must if you're spoiled like me LOL.

@KeanF84 Жыл бұрын

Nice building! Also I see the building is sitting on the larger pad, knowing where the doors are going to be slope the concrete so water doesn’t blow in during rain is important and then you dont need a weather strip on the floor and you can gain a ramp, i usually cut out the concrete before it sets up when im finishing it. Cut/dug down at the edge 1.5 inches and back 16” helps for low cars when the garage slab is up. And yeah, 10’ square cuts minimum on slabs. (The concrete guys should have known that) Also yeah the cuts look 👌👌you try cut any concrete in perfect squares if possible. Like sidewalk is say 5 feet wide, you cut it every 5 feet.

@bcompton53 Жыл бұрын

Long story but I had to build my own Carolina carports shop. I’m not sure I understand how the windows get trimmed out. The heads of the screws that hold the window onto the building cause a gap that the j trim sits against. Can you get me photos of what they did on your windows? They just fill the gap with caulking? Thanks.

@bryansenulis7242 Жыл бұрын

Good info bro

@DaveTecho Жыл бұрын

Thermal insulation is much cheaper to install before the roofing and wall panels get attached. Silver side inside, as it is more light reflective than white paint. The slab edges should ALWAYS be about 12mm or 1/2" lower all around, where the doors and walls sit on it, than the slab level inside the shed. that way, when it rains, the water stays outside. Otherwise, every big downpour, results in a pool on the middle of the floor. Your power wires and power outlets should all be plastic, not metal. Any internal exposed wires can connect through metals.

@dandescalso1939 Жыл бұрын

You said you would tell us how much the shop cost, but you did not even mention it.

@FlyinGato Жыл бұрын

My apologies, I thought I did, it cost 19,850 for the metal building itself, and another 8500 for the concrete as well as all of the gravel I purchased.

@WaltWW Жыл бұрын

@@FlyinGato Thanks

@Joda30088 Жыл бұрын

@@FlyinGato that's cheap for concrete and gravel

@FlyinGato Жыл бұрын

All of the labor of the dirt, stumps, and gravel was on me. I leveled and formed my own forms for the concrete as well, and had 4 of my own guys there to pull the concrete with two hired concrete pros to finish it. Lots of savings there for sure

@Joda30088 Жыл бұрын

@@FlyinGato Definitely!

@the_DOS Жыл бұрын

Love the s2000! Got a silver one myself!

@user-kf8te6ud5f Жыл бұрын

Electrical job is terrible it would never pass electrical inspection!

@GeorgeBailey-mo1mq 2 ай бұрын

I have been going to build a Metal Garage, but have decided to go with a more expensive Pole Barn due to the Garage doors that you mentioned and just easier to wire and insulate.

@FlyinGato 2 ай бұрын

glad I was able to help

@sandmansimms5704 4 ай бұрын

how high is it, leg height? I want to do my next one high enough in case I want to put an upper level later

@nylronetynarf6952 Жыл бұрын

Did I miss it? What did you say the cost was for the concrete and the building?

@promodelred Жыл бұрын

Don’t kick on the door, kick DOWN on the door to release the tension

@jcvice5421 Жыл бұрын

How much you paid in total for the garage?

@Imnotyourdoormat Жыл бұрын

Steel doesnt rust? Those boys restoring the Battleship TEXAS would probably argue that....hahahaha lol

@UncleSarkis Жыл бұрын

Thanks for sharing. When are you building your new shop in Florida?

@FlyinGato Жыл бұрын

That’s what has kept me so busy lately, right in the middle of the build currently

@UncleSarkis Жыл бұрын

@@FlyinGato Awesome. I hope you're filming if you can and it's not going to set you back too much. No worries if not, thanks again, I'm looking forward to seeing this one when it is complete. I'm a bit jealous 🙂.

@thewayidoit8895 Жыл бұрын

Thats an enclosed carport. Nice to have enclosure but realize its very inexpensive.

@serenityplantation7638 2 ай бұрын

You don’t have wainscoting you just have a different color panel on the bottom

@Honda1k Жыл бұрын

Why don't people spend a little more and do vertical siding instead of horizontal

@TheHillrat4wd Жыл бұрын

100% Agree

@thewayidoit8895 Жыл бұрын

Everything we don't like adds "spend a little more"

@arthur1920 Жыл бұрын

17:23 is that cracked pavement under the Mazda?

@BayJoua 4 ай бұрын

I didn’t see a single Mazda in the video.

@FlyinGato 4 ай бұрын

Maybe under the S2000? Wasn’t cracked, you may have seen a relief cut

@bryansenulis7242 Жыл бұрын

O how much was the cost...for slab and building....did u need permit? Any info would help because I'm going to build one in Houston TX for my race cars and tools..and to get away from wife