Excellent idea as these connectors are a weak point. Several times on liftoff, my FW450 v.2 has lost GPS and suddenly the heli seems like it is in 3D mode. What a handful getting it back down safely. Secondly, had trouble FINDING the satellites getting ready to fly because one of these wires is not making proper connection. Sealing the connectors as you've shown and a zip tie or two around the wire/tailboom completely solved this. (And since I've adapted a shiny, scale Hughes 500 fuselage wrapped around the mechanics, really do not want any connection failures leading to an expensive crash! Thanks so much for posting this.
@nickdean4682 жыл бұрын
Good information thank you for making this video. I had bought one of these H1 gps for a 700 size heli I haven't installed mine yet. I'll definitely keep this in mind before I do.
@davaoeagle72713 Жыл бұрын
Thank you for sharing. I just bought my FW450L Heli need to do that before bad things happen. Great information 👍 thanks again.
@andrec.136 Жыл бұрын
I was searching to see if this could be used with an Ibus receiver and instantly found my answer. You also opened my eyes to two unknowns. The first was that there is an H1 lite and secondly the connection issue. I am looking to upgrade my Kbar to this
@darrenrobillard94963 ай бұрын
Right on, I used liquid black tape
@DerredmaxTRIAX6 ай бұрын
Thanks!
@bobzybob1 Жыл бұрын
Solide! Thanks again.
@keithdriggers95782 жыл бұрын
Hi, anyway you can tell us where to find the glue stick? Name, etc. thanks for the video and time.
@gdhall53112 жыл бұрын
Good job Cruzroy, I used liquid tape.
@jeffkraus145712 күн бұрын
Hey Cruz, gotta link for the rubber stick? Thanks buddy!
@05rickie Жыл бұрын
My brand new V2.5,after initial setup and compass calibration,5 min. test flight👍,next day went to fly again and only got flashing yellow light ,would not turn green,the plug inside the GPS module came loose,had to remove the GPS module to expose the plug,plugged it back in then put some gorilla tape on the plug to keep it secure,reinstalled the GPS module,now works perfect,thankfully it did not happen in flight,would have been ugly,I also put some zip ties on both ends of the cable for added security.
@did3d523 Жыл бұрын
barbarian
@CRUZROYHelicopters Жыл бұрын
???????????????????????????
@MrRockq11 ай бұрын
i have h1 heli on trex 450 dfc. until now , never found solution about shake after airbone,, my main shaft, tail shaft, blade ,, avery thing good condision( center). all part use original align.. after a couple time i try and looking some problem may i miss,,but i dont find any miss procedure. i change again to use microbeast fbl.. and work fly normaly..but when i use h1 again ,, still shake again.. i hope someone can give me solution in my comunity have 3 h1 heli in 3 people have same problem.. thank you
@CRUZROYHelicopters11 ай бұрын
have you done the servo check in the software, with the H1 nobody seems to care about 1. CG and 2. Blade tracking..here is a video about servo check, if you get it right your blade tracking will be correct kzfaq.info/get/bejne/f8Wgpbxj0ai8n3k.html its on the FW450, but H1 has same in direction center stick high stick and low stick if you have rotor head lines like SAB Align and fw and others make sure the are correct....blade tracking can cause shaking and also adjust tail in software
@MrRockq11 ай бұрын
@@CRUZROYHelicopters thank you for your respon, all servo work correctly direction, cg little tail heavy but i think its ok , blade no tracking in any direction,, flat zerro deg, in center stick. also with tail,,its all normal condition. when i use old align 3gx again.. its work great to fly..
@Tye1327411 ай бұрын
@@MrRockqturn your gains down
@bradyates7046Ай бұрын
I am using silicone nothing hot.
@ReviewCantina Жыл бұрын
Thats not a good fix perment connecting components that need to detach. If you have a boom strike in a crash you can kiss the controller and gps goodby, they are going to get destroyed. Fixing the wires to the connector is good idea if they are poorly connected and come apart. Your better off using RED tap on the connector to the gps. That would stop it from coming loose, but would still be able to disconnect in crash.