Seems like it's some kind of auto face recognition and blur program. Notice how it blurs his face but not all the time, and random blurs appear at times like the algorithm is confusing some pattern in the frame as a face. If it is an auto face blur program, it doesn't work very well.

wise decision, mate! You won't regret it. FALs are way underrated, in Europe at least they're completely forgotten, and being sold around AK price levels. Btw check out my FN FAL accuracy video, with Norma Jaktmatch FMJ this gun is 1,5 MoA/110 yards, iron sights.

One of the greatest rifles of all time, truly an implement for any situation.

Here in Brazil is normal the use of rifles 50 years old, by our rmy. @@Sinaimedve007

cherish and love your FAL, mate! you will never hold a better milsurp rifle in your hand.

wellcome wish u loads of fun with this marvellous rifle

+Josie Walesthanks, and you are welcome, mate!

thanks a lot! FN FALs rule, such fun guns.

Hey buddy, what do u mean by lemmon barrel? I dont understand that. Yes,.i willhave more.humour and jokes, the zee germans are comin'!

Bear of Sinai gas plug is loose on the front, I replaced the plug and same issue so i figure it was improperly machined OR just beat to shit not really sure. I was told to silver solder on the inside of the gas plug to counder it but that's not working at all.

ondamedjedi can u post a video abiut it? The gas plug is fitting snugly on all fals i' ve seen. So there is a gap between your plug and the gas block, even after u put the plug back? Are u surely.not interchanging metric and inch pattern parts?

When shooting: Set gas at 5. Stoppage drill: rifles fires once then stops. Work charging handle. Rifles fires one or two shots and stops again. safety on, pull rifle down close to you, turn gas to 6 or 7. Carry on firing. Repeat if needed. Basically, gas at middle setting number for a start, then more gas if it doesn't reload. It depends on how hot, cold the day is, or how fouled the gas piston is. If this happens with full gas, survive, then get your rifle to an armourer, or clean it yourself.

Hahaha yeah that's kinda true

I brought mines FULLY closed and just kept her that way......is that a BAD thing????

Yes. You're needlessly beating the rifle and yourself up. This is a very good video on how to adjust the gas system.

well i just bought it in a local store, was sitting there since days of Noah. ammo is double of the us price in hungary, therefore such guns sell slow. btw any fn fal copies will do, all of them are gorgeous.

check if the gas collar was not screwed/put back the wrong (opposite) direction... if the hole is fully open, it could never cycle.

+Bear of Sinai Maybe it is because of ammo.That hole on the top is wide open and it still works, ill try a different ammo in the future to test this once more. And thank for reply.

73288 so... something just doesn't add up here. If the gas port is open, i.e. the hole is there, visible, large, there is just no way that the rifle could cicle properly. Except for a WILDLY overloaded cartridge, but that would show and tell right away on the cases (ruptures, cracks e.g.). SO I would rather poke' around the: -gas plug (clean? no gunk in there? is the "A" sign on the top when reassemlbed)? -gas collar (is it properly adjusted)? -what happens if you go all the 14 clicks the other way? And yes, trying some other ammo is also a very good idea. Keep me posted, pls.

Keep setting at th setting allowing the most gas to eject the brass case, assuming a #1. By closing the port to the maximum, assuming #11, or beyond the minimum causes undue wear and stress to the receiver. Your beating your receiver to a pulp. You can insert a poly tecoil block to help reduce wear to the receiver.

I had some old (1963) Spanish surplus ammo. The FAL would not eject it no matter what the gas setting. I figure the powder must have degraded. The primers were all fine, though. So, I bought a collet puller and pulled the bullets on 500 rounds of ammo, then reloaded them with fresh powder and they worked fine after that.

No, it is a feature which enables the rifle to function with poor quality ammo, and also ín case the rifle gets really dirty, and also it is a good feature to improve reliability in adverse weather conditions (extreme cold, heat etc)

+Leo Colo BUILDING BETTER WORLDS!!!!! :) yeah bro'! I actually did believe in that when I signed up to be a Space Marine.

Sorry mate, missed your question. The gas port is too closed, open it up a little bit, you are hammering the piston with unnecessary huge amount of gasses. This also might degrade your accuracy, as less gas is used to propek the bullet than the ideal qty. On the other hand, 4inch groups with a Fal are not tragical, especially with surplus ball ammo. Buy a couple boxes of other ammo types, e.g. hornady, prvi, saloerbellot etc., and trial and error experience will tell u, which ia the optimal one. Use steady conditions, e.g. sandbag, rifle support, shoot slow and calm, try.to cut out the human factor. My best group with Fal was 1.5 MoA, with Norma Jaktmatch ammo (bit pricey....) Have fun!

Thanks very much

Colin McQuaid what i mean mate is if u achieve 4 inch with ball ammo, i bet u will.go under two moa with quality ammo. Cheers from Hungary!

Just a budget Timex which I still have and use when I am gardening, on the range etc 🙂. Cost like 50USD back in A.D. 2008.

It was raining, and it messed up the camera focus...

rockape252 True, though you can turn off the gas plug and all the gas will propel the bullet but the rifle will not cycle. It will behave as a single shot rifle that needs to be hand charged each time.

That is true. I know from experience. @@BooDamnHoo

You know, I never said you have to remove it, i merely shown how to do it if you needed to.

well happy to help. my fal just needed two extra clicks for steel cased ammo to be able to cycle perfectly. make sure to ckean the gas port's gas hole thoroughly. fals can go on forever with steel cased ammo, dont worry.

I took her completely apart and the gas tube and piston was caked with 50 years of residue. Cleaned her up and lightly lubed the piston and tube then wiped her clean before assembling. Taking her out tomorrow to see how she runs. Thank you again.

Soooo, how'd it work out for you?!?!?

All good. Runs like she used to.

I just picked up an IMBEL. I have no idea what I'm doing with it so I'll be careful adjusting the gas system. Are you still shooting Wolf through yours?

What? The front sight is timed to the receiver when the barrel is installed into the receiver. Unless the barrel itself is unscrewing from the receiver, there should be no movement of the front sight.

The front-sight and barrel and receiver assembly move as one piece on the pivot. The rear sight is on the butt-stock assembly. There is some slop in the pivot so the two assemblies move depending on how you hold the weapon.

Jeremy Ardley Ihhh, I misunderstood. I thought you were saying lateral movement of the front sight assembly was possible. While you may be technically correct, I think you're giving the tiny movements possible too much credit. We're talking about battle rifles that are capable of 3 NOW at best. That, combined with standing, offhand firing likely makes any vertical shift possible from the pivot more or less insignificant.

The flex is a rotary motion around the barrel axis so more left/right and less up/down. I have shot this weapon with iron sights in top military marksmanship contests and I know precisely how the weapon moves under different grips and pressures. When firing prone at snap targets and at long distance fixed targets you will always get better/more consistent results if you hold it the same way. At 300m it is as much as 8 inches lateral mean impact point - i.e. outside of the V-Bull.

Jeremy Ardley At 300 meters, you're going to get a 9 inch grouping, at best, with a 3MOA rifle. I have no doubt that you firmly believe that the wiggle in the pivot affects accuracy. Many people also falsely believe that poor upper to lower fit negatively affects accuracy in the stoner pattern rifles. It would be even more evident in the AR-15 if such issues were valid, as that rifle is capable of great precision, at times even under 1MOA. Furthermore, being a ring and post system, the post doesn't need to be stationary for the sighting system to function normally. cheers

Absolutely... True! The reason I made this video was to help people who just bought their FAL and it wouldn't cycle properly. My FAL was assembled incorrectly when I bought it, so I had to figure it all out by myself, and it was no fun 😭

Yes, there is-unfortunately I had none, and also did not find any in Europe.

Imbecile, FN Herstal Belgique

aqui no brasil fn fal 762x51 é fabricado pela imbel

TacticalTigerBalm basically, once you find the optimal setting for your FAL (each one is a little bit of an individual), you can pretty much forget about the gas nut, like 4ever.

ok

sorry for the quality... hope the content is compensating you for that