I bought the version before this one HS01 on my own. Best iron I ever used. Heats up so fast. Much more convenient in every way for my uses in automotive.
@speed_rider362Ай бұрын
Thanks for the tip, just bought mine. I'm using the similar iron GVDA GD300. I like this FNIRSI better mainly because it has the cover cap.
@peterlarkin762Ай бұрын
I got a Sequre iron out of curiosity last year after it was on this channel. Its far better than I thought it would be, ended up using it for almost everything. The t12 tips seem to last really well too. Rapid heating and the auto standby sensor makes it so frikn convenient.
@Suzuki_B-King_HooliganАй бұрын
Currently waiting on mine to be delivered, agonizingly slow from China. Will be replacing my TS80P, which maxes out at 30w. To be used with my ZMI Power Bank that can easily drive it at 20V 100W without breaking a sweat, it maxes out at 210W with 2500mAh total capacity, 100W per port @ 20V & 5Amps. Not a cheap power bank, but one of a select few that can actually charge up a laptop using USB C. The cartridges being directly compatible with JBC C245's, makes for a lot more tip possibilities, where the TS80P still only has the 5 proprietary ones since its launch. Edit. Just arrived earlier, tested with a FNIRSI FNB58, and it works AWESOME!!! Really fast heating up and maintaining temp while soldering. Tested calibration on a 191 Thermometer Tester, and all 3 set channels were spot on their set temperatures, 350°C ,380°C and 420°C Out of all the tips, I'm really prefering the small knife KU. Perfect for general use.
@stragulusАй бұрын
Thanks for the review! I just moved across continents and had to leave my Weller WES51 behind, so I'll go ahead and try this one instead. It reaches temps faster than my old Weller and holds its temps better as well. Impressive. And if this works off a power bank it's portable too. Not sure I will have much use for that, but it's a nice bonus.
@mabbaticchioАй бұрын
Just ordered one. Noticed your video on the product page. Nice!!
@pileofstuffАй бұрын
My biggest concern with the various new "smart" type of irons is that they all use proprietary (different, incompatible) tips that seem to have limited availability after a year or so.
@peterlarkin762Ай бұрын
Sequre smart irons uses very common T12 tips, they'll be around for a long time.
@m80116Ай бұрын
@@peterlarkin762 is this FNIRSI following any standard or not?
@Suzuki_B-King_HooliganАй бұрын
It uses JBC C245 style cartridges, and is compatible with JBC originals. This platform has a huge variety of tips, and available all over.
@buriedbits6027Ай бұрын
@@snakezdewiggle6084I saw tips sold separately on AliExpress for about 21PLN which is roughly 5USD / tip
@waynar3899Ай бұрын
Nice..i want one
@bones007ableАй бұрын
Don't need another corded iron .... I bought a cordless one from temu for 10 bucks , works good and you don't have to drag a power cord around with you like when working under a car dash... lasts for about 20 mins on highest settings....
@you2ber252Ай бұрын
I have a similar one with its base station (you tested it 2 or 3 years ago... the base station was so bad that it was disturbing the image of your cathodic ray tube desk clock). The problem with it is that the tips are very cheap but the surface tratment is also very cheap, so they oxydate very quickly. You must constatly use the brass sponge to keep them clean.
@you2ber252Ай бұрын
It would be inrersting to know how's the quality of the tips of this one.
@davidgriffin79Ай бұрын
Very similar to the Pine PINECIL. I prefer to use the PINECIL to a Hakko FX-888D for lighter circuit board work as it's more nimble to use.
@gregsullivan740826 күн бұрын
Thanks, but it would have been better if you'd tested it at full power - you had the power setting on 65%! (although you'd of course also need a 100W supply - did you say you only had a 60W supply?)
@tylerd947Ай бұрын
cool
@markmarkofkane8167Ай бұрын
Interesting. At first, I thought it was cordless. But that's still pretty good.
@stragulusАй бұрын
I assume you could use this with a portable power bank so you can use it outside easily as well. That is really neat.
@Suzuki_B-King_HooliganАй бұрын
Just ensure it's a Power Bank with the required protocols and specs. Cheap ones are a waste as it needs at least 9V to run. Most popular banks go up to around 20W PD. A decent one is quite expensive, but then is compatible with much more, even powering a laptop in the case of my 210W ZMI Power Bank.
@dobroplayer7Ай бұрын
This has to be plugged in when in use right? Has to be.. I like the precision tips a lot, probably going to order one right now. I wonder how long a large battery pack would power it for?
@12voltvidsАй бұрын
Yes its not cordless
@dobroplayer7Ай бұрын
@@12voltvids someday there will be a cordless!! Wouldn't that be awesome
@lezbriddonАй бұрын
@@dobroplayer7 on the bench, corded weller, if your mobile to fix automotive things, something corded that runs off of a drill battery, if you 'may' need to do pcb stuff 'in the field' then drill battery iron or small butane or one of these but as i'm as gentle as a gorilla with tools these look delicate...
@awaazhoosein656529 күн бұрын
Can this be on hold day? Is the tip genuine
@awaazhoosein656529 күн бұрын
Which site can i get this for reasonable price
@jimhalpert4017Ай бұрын
Hey man i have a sharp vl-n1u. If I mail it to you will you fix it
@12voltvidsАй бұрын
No parts available so no guarantee i can fix. Can try
@Suzuki_B-King_HooliganАй бұрын
Just updated to the latest V1.5 Firmware from FNIRSI, no changes in the menu and features, and no description on what was updated from their site.
@12voltvidsАй бұрын
Unless something isn't working right I don't normally update software.
@Suzuki_B-King_HooliganАй бұрын
@@12voltvids I got a response from the vendor: V1.5 20240321 Changed in version V1.4: 1.Modified the version number 2.Optimized the BUG displayed in the settings interface APP_HS_02A_V1.5_20240321.BIN
@RectifiedMetalsАй бұрын
Look like c115 tips. I’m interested to see the chisel tip work. I paid $40 for a JBC one and it was total shyt. Won’t hold solder on the point. Get a silicone pot grabber and hot swap the tip
@Suzuki_B-King_HooliganАй бұрын
These use JBC C245 style tips, compatible with JBC originals.
@BarbarapapeАй бұрын
A great idea, but i have bought many of these types of soldering irons only to find it nigh on impossible to buy spare tips. Best to invest in branded one that supports them.
@gregsullivan740826 күн бұрын
It's compatible with JBC C245 tips 😀
@Barbarapape26 күн бұрын
@@gregsullivan7408 Make them last, they won't be any spares available when you need them.