Focus ST Rally Innovations Front Splitter 3-Piece Matte Black Aluminum 2013-2014 Installation

No video

Focus ST Rally Innovations Front Splitter 3-Piece Matte Black Aluminum 2013-2014 Installation

Рет қаралды 44,560

Күн бұрын

Product Link: www.cjponyparts...
This Rally Innovations Matte Black 3-Piece Aluminum Front Splitter is for 2013-2014 Focus STs. Built tough in the USA, this all American made front splitter has the long-lasting quality that you can trust from the masters at Rally Innovations. Crafted as a three-piece design, this front splitter bolt-on quick and easy with all the required hardware already included.
Check out more Focus ST Body & Appearance parts from CJ's here:
www.cjponyparts...
Check out more Rally Innovations parts from CJ's here:
www.cjponyparts...
Subscribe to CJ Pony Parts on KZfaq here:
www.youtube.com...

Пікірлер: 25

@RookieRancher727 7 жыл бұрын

Do you have to remove the front splitter in order to change the oil??

@Zerogivengarage 7 жыл бұрын

No, with the plastic panel disconnected from the back there is still room.

@RookieRancher727 7 жыл бұрын

Bill Tumas thAnks bill. love the videos!

@jasonlitz2907 7 жыл бұрын

Kind of like but won't the coated metal scuff and scrape underneath? I worry about bending one on a pot hole.

@Zerogivengarage 7 жыл бұрын

Sure it can scuff just like your bumper if you hit something. If you hit a pot hole bad enough to bend it you would probably take out a lot of other parts along with it.

@megolito961 6 жыл бұрын

Thanks for this video. ive been on the fence of getting a spoiler. i really want somthing that actually makes downforce. does this one make any downforce at speeds above 100? im trying to get rid of the floaty feel my car gets at 110mph+ i track my car alot. 2014 stage 3 focus ST

@robinlehner8269 5 жыл бұрын

Is this also working for a 2012 st?

@yelnocbocaj1 5 жыл бұрын

Will this splitter be in the way of the stow and go license plate bracket used in another one of your videos for ST

@cjponyparts 5 жыл бұрын

Yes it will, you would have to customize it to make it work.

@nicknicolosi1 6 жыл бұрын

Hi, did you ever tried install on a 17? I couldn't get the side screws of the center piece on, I drilled the hole, but there is like an inner wall on the bomber. I have it on with two screws only right now, seems solid. Thanks for the video tho.

@cjponyparts 6 жыл бұрын

We were told the 17 was the same fitment but have never had one here to verify.

@nicknicolosi1 6 жыл бұрын

CJ Pony Parts i understand, everything fitted smoothly, except for two screws. I will try and drill two new holes few inches towards the center, that should clear that inner wall problem. Other than that, it's solid, and I love the look.

@cjhanselman3354 5 жыл бұрын

Pull your splash guard out you have to cut an opening so you can get the nuts on the bolt in I just did it on my 18 the other day. At the front of the splash guard has a square section cut a notch into both sides so you can get to the bolt.

@CharlieFBrown 2 жыл бұрын

@@cjhanselman3354 yo i have an 18 st that i wanna put a splitter on but i have no mechanical knowledge. Is the process for the 18 the same as the 14 shown in the video? Take off that metal bar and open up the splash guard a bit and just screw it in?

@cardenas7pointez 6 жыл бұрын

Can I use that same front splitter for a 2015 Ford focus se sedan?

@cjponyparts 6 жыл бұрын

We have only ever installed it on the ST, I wouldn't think it would fit without modifications.

@mightyrome9420 7 жыл бұрын

does this mod hold on well while driving at high speedes? cause it looks a bit fragile and i think this mod loves to catch air

@UnfocusedRacing 7 жыл бұрын

mighty rome I've had mine since September 2015. Holds up grate and is not fragile.

@completelymustang 7 жыл бұрын

Mine has held up at speeds over 140mph. As long as you use the provided hardware, you will be fine.

@mightyrome9420 7 жыл бұрын

ok thanks because i live in germany so i need a mod that holds well at high speeds. long live the autobahn. between 140 and 160 mph should not be a huge difference i guess

@UnfocusedRacing 7 жыл бұрын

I've done just over 100mph with mine and no issues.

@AllAmericanLAX 2 жыл бұрын

Do not forget to cut the splash guard. It is a b**** to do it while everything else is on

@UnfocusedRacing 7 жыл бұрын

Hate to correct you guys but this has been put since before the 15+ model version. I've had mine since September 2015. I did remove the front bumper cover to install mine which I think is easier. www.focusst.org/forum/showthread.php?p=937954