A few people asked could I make an episode for those whom are just getting started. So hopefully if you are one of those people, you will get something out of this.
Пікірлер: 52
@zestycomicsbytomsteele241110 ай бұрын
Thanks, I am restoring a 1948 Motorola 6-tube AM receiver that I picked up. I didn’t intend for it to become a hobby but it’s turning into one. All of the caps are melted and the insulation is so badly damaged that I think it shorted at some point and fried everything. This is helpful. Very detailed explanation of how everything is done and how it all fits together.
@edwardhannigan63242 жыл бұрын
He Seth, just a fab repair from start to finish..Me being a newbie as well, this sure has answered a few questions. Great video and instruction...keep em' coming..Ed..uk..😁
@misterradio50352 жыл бұрын
Thanks a lot Ed! Take care over there!
@terryblackman62172 жыл бұрын
Thanks so much for showing a more in depth way you repair your radios.
@ethelryan257 Жыл бұрын
It was cool!
@aryonllewellyn2 жыл бұрын
I believe some vintage valve(tube) radios used to use the pilot lamp(s) as a fuse. So if the pilot lamp(s) failed, no electrical continuity.
@waynebrettzky992 жыл бұрын
Thanks for your this. I’ll definitely watch it
@MrMersh-ts7jlАй бұрын
I just found your video and it was incredibly informing. I just rehabbed a zenith AA5, including an output IF can. I'm getting an approximate two kilohertz tone that's very loud between stations. I've traced it to before the volume control and it's actually louder than the stations themselves. Any thoughts or a direction you might be able to point me in? Thanks for the great video
@greggaieck48082 жыл бұрын
Mister Radio it is cool when you put Jack on the radio for a cellphone to listen to music
@hestheMaster2 жыл бұрын
Ha, an Emerson model 518 with Arvin knobs. They would be rather loose so they bent the tangs wider on the two pots so they wouldn't slip off. Dang OCD strikes again for noticing that! Like these longer more descriptive and thorough videos. At 33:49 those black "doomajigies" are called a strain relief . They actually have tons of sizes but the line cord that is preferred is called a SPT-1. Thinner and easier to work line cord for a lower wattage unfortunately you have the more common SPT-2 line cord and is better for transformer type radios. It is used for extension cords too. Strain reliefs like 6N-4 ,6N3-4 are used for SPT-1 and 6L-1 or a 7N-2 for the SPT-2 cords. They make a special tool that keeps you from breaking any strain relief . See Philmore 63-640, I have one and it works great. A 50B5 was used in these because they didn't change the circuits when they went to two miniature tubes in a later manufacturing run. Originally it was a 50L6. A 35Z5 got replaced by a 35W4. I'm glad I'm not a newbie because I would be so confused. Steve
@marka19862 жыл бұрын
I run into so few strain reliefs any more, that I never bought the tool. However every time I pinch my hand when the pliers slips off wish I had the tool.
@barfoonisland20032 жыл бұрын
I had a similar Emerson radio like this years ago. The cabinet was bakelite without the patterns sen here. The dial was more art deco too. Maybe I had an older model ?
@TheSquaredM2 жыл бұрын
I really wish you would show examples of how you wire the input cord. It seems like every video I watch you do that, you do it a different way. Maybe some actually drawn schematics will help? With examples of the different cases. Sources for the transformers would be nice also, you showed the box and a vague website but it would be nice to know what you actually ordered and where you got them from.
@misterradio50352 жыл бұрын
Thanos for the input. I will try to draw somethign for the upcoming episode
@seanlynch184111 ай бұрын
Fantastic video. I have a Hallicrafters SX-73 and some of the back terminal thumb screws have a little green corrosion. Would you be concerned in that case?
@mikemoran54394 ай бұрын
Great video! Is that a YDHC isolation transformer for the bluetooth portion?
@briansmith9698 Жыл бұрын
Mister Radio isn't it true you want go higher in voltage not lower when recapping those radios? Also I have a electrolytic that says 30mfd 30mfd 20mfd 20mfd then it says 150 w.v,yel 150w.vred 150w.v blue 25w.v green what voltage and and microfarad capacitor recommend replace it with?
@ethelryan257 Жыл бұрын
I love it when Seth uses WD40 - he should have a 'trigger alert' for it just like Eric of South Main Auto does whenever he's about to use Brake Cleaner. The horror of it all. (Oh, and, why, yes, I am an electrician with decades of experience using WD40 and not once a recall because of it. But, then, why would people who actually DO instead of just sitting on their momma's couch in the basement know anything?)
@garyjohnson4608 Жыл бұрын
If I want to learn more about this, are there any books I can pick up that you would suggest I read and study ?
@greggaieck48082 жыл бұрын
Mister Radio the 1947 ALL American 5 radio Receiver is cool
@justincase38802 жыл бұрын
Hello, on the isolation transformer, what is the supplier and part number? Schematic? BTW, nice work …
@aprules2 Жыл бұрын
Hi what was the part number on that little isolation transformer you used?
@frankroper3274 Жыл бұрын
I have a zenith 5 tube clock radio that has a couple caps with 100 on one side and 22,5 on the other. They are relatively small so I am thinking 22.5 MFD is not what it is. Could it be 22.5 pico farad?
@greggaieck48082 жыл бұрын
Mrster radio all American 5 radio Receiver with broadcast band is good for DXing at night
@garyjohnson4608 Жыл бұрын
Which brand of solder do you use ? Kester ? Other ?
@oscarhernandez82502 жыл бұрын
Could you please, share a schematic of your Bluetooth wiring? Regards
@juanmiguelcarballo32002 жыл бұрын
Saludos Maestro: Buen Video. Un Cordial Saludo desde Cuba.
@wardduffield4893 ай бұрын
Yo Tengo una RCA de ondas cortes del ano 1936, y puedo recibir Grandma muy bueno durante las noches. Saludo desde Nueva York.
@wardduffield4893 ай бұрын
Se puede verlo en you tube
@garyjohnson4608 Жыл бұрын
The yellow caps you are using as replacements, by chance are they Mylar ?
@briansmith9698 Жыл бұрын
Mister Radio you can still buy brand new paper capacitors Tube Depot sells them how long you think they last? Some people might want keep radio look more original new paper caps.
@wardduffield4893 ай бұрын
No alignment? No douching the tuning cap?
@ant2420022 жыл бұрын
Anyone know how to rewire a loop stick antenna?
@shopwornbear11712 жыл бұрын
Hello Seth. One thing you really need to tell a newbie (I would be a novice) is to discharge their caps before messing around with cutting them out, for safety's sake. As most of us know, those things can hold a charge, and can give you a nasty surprise if not handled correctly. I use a resistor and a couple of alligator clip wires to discharge caps, cheap and cheerful, perfect thing for anyone looking to outfit an inexpensive radio repair kit. Full disclosure; I've never had my hands inside a tube unit, but have had my hands on many electronics (mostly computer boards and cards), but would still discharge any and all caps before messing around with them, just in case.
@misterradio50352 жыл бұрын
Yes. That is true. Luckily, unless for example electrolytics are not grounded properly , they seldom hold a charge
@byrane7592 жыл бұрын
Seth, where do you get your replacement parts?
@misterradio50352 жыл бұрын
I get capacitors and resistors either from mouser or from Sal's capacitor corner. Switches from Amazon, transformers from Alibaba. Tubes can be had for cheap on Ebay
@greggaieck48082 жыл бұрын
Mrster radio all American 5 radio Receiver is cool
@danielauen7790 Жыл бұрын
Im looking at a schematic and a parts list here, Its got 8 paper, 1 electrolytic, two micas, and one variable capacitor. apparently I shouldn't worry about the micas, but all the papers are labled as "mf", Is that Millifarad? The radio is a 4 tube superheterodyne battery unit. 1.5v A voltage and 90v B voltage. there does not seem to be any way to connect to the grid, or a rectifier, so its a fully dc radio. I know the papers have to go, and the electrolytic, But what about the tuning capacitor? The radio in question is a Galvin/Motorola 47B11
@jeffreyhickman38712 жыл бұрын
Bakelite? These radios 📻 are often 5 tube. The speaker 🔊 must be field coil. I wonder 💭 why these weren’t called 📞 “Christmas Tree 🌲 Light 💡 Sets”, regarding the special circuitry these radios 📻 have. Power 💥 is cut to the WHOLE radio 📻, in the event of the failure 😞 of the dial light 💡 bulb. This is often where owners would draw ✍️ the line on even thinking 🤔 of repairing 👩🔧 the radio 📻. They thought 💭 it was the end of the line for the radio 📻. This often misunderstood “OFF” feature, guarded 💂♀️ against radio 📻 damage, electric ⚡️ shock, or fire 🔥. Your friend, Jeff.
@mikedragneff68042 жыл бұрын
Have you ever used a permanent mounted Bluetooth on a PCB mounted internally?
@misterradio50352 жыл бұрын
Not really, because the quality of these bluetooth things are not great. I would rather make it easier for the user to swap whatever out if needed
@robinsonsoto84712 жыл бұрын
Is that T- rez??
@misterradio50352 жыл бұрын
Out in the yard? Yeah. We have a 7 foot tall plastic dinasaur in the yard
@MrGigi-dz9cv Жыл бұрын
The new capacitors are so much smaller ...
@dicko-2009 ай бұрын
no dim bulb,
@Cimone904 ай бұрын
That's what the variac is for.
@johnfranklin52775 ай бұрын
So a strong enough jolt of electricity can cause a heart to stop beating normally, and cause it to go into Ventricular Fibrillation. This means the ventricles are QUIVERING, and not pumping blood. If a regular heart beat rhythm is not quickly restored. The person will die. So surprisingly, another jolt from a defibrillator, can usually shock the heart back into a normal rhythm. Our hearts actually function on electrical activity.
@wardduffield4893 ай бұрын
No ongoing commentary on cap polarity on a case by case, no inkling of which modern style is the appropriate replacement. No suggestion for sources.
@goldenboy5500 Жыл бұрын
you make isotonic mistakes because your a little on the sloppy side
@towerman757 ай бұрын
Lost interest early into the video. Reason being, your bench looks like it is intended to rebuild automotive engines, and rebuilding radios, is a side line. The tool chest in the background, loose pieces parts in and under the chest, and absolutely no real test equipment. Sorry, but that's the way I see it.