Ford ACM (Audio Control Module) No Sound, Flashing Clock / TIme , Popping Noise

Рет қаралды 11,547

Күн бұрын

Join this channel to get access to perks:
/ @robertdotterer
Today we have a 2011 Ford F150 ACM (Audio Control Module) that stopped working. The customer said the clock would just flashs nd there was no sound from the speakers. These modules are very similar across other models. They can have popping noises coming from the speakers too.
Tools Used:
HAYEAR 4K HDMI Microscope Camera Kit for Industry Lab PCB USB Output TF Card Video Recorder +180X C-Mount Lens + Big Stereo Stand +144 LED Light
amzn.to/3Xx4Rui
YIHUA 8858-I & 928D Kit bundle with the #8858 Hot Air Gun Heating Element with Iron Holder, Cleaning Kit, and Accessories (23 Items)
amzn.to/3wjaT5x
MG Chemicals - 424-LF Desoldering Braid #2 Fine Braid Super Wick for Lead Free Solder, 0.05" Width x 5' Length
amzn.to/3D4Dxv0
MG Chemicals - 8341-10ML 8341 No Clean Flux Paste, 10 milliliters Pneumatic Dispenser (Complete with Plunger & Dispensing Tip)
amzn.to/3WrYIxR
MG Chemicals 4860 63/37 No Clean Leaded Solder, 0.032" Diameter, 0.6 oz Pocket Pack, 18 Grams
amzn.to/3XyPbGL
Portable NF.Mini Soldering Pen
northridgefix.com/product/por...
Precision needle probes Straight and Bent
northridgefix.com/product/pre...
0:00 Intro
0:15 Overview
1:12 Inspection Of Board
3:17 I spy Something Fishy
4:00 Uh Oh We Found Our Issue
6:35 Removing The Chip
11:22 Cleaning The Pads
13:10 Putting New Solder Down
14:50 Reinstalling The Chip
16:40 Checking The Pins
17:30 Final Inspection

Пікірлер: 47

@servcomparral8090 3 ай бұрын

1 week working on my stereo (2012 mustang), i almost give up until i saw this video, now it works, thanks!!!

@RobertDotterer 3 ай бұрын

Glad it helped!

@nolansalmond4343 Ай бұрын

Couldn’t believe this actually worked. I had tried so many other things but nothing was working. I now have a working stereo in my 2010 ford mustang, thank you.

@jeffreychristen1715 6 ай бұрын

This video saved me a lot of time and money. I've gone without a radio for a long time and just fixed it in 40 mins thanks to you. Although hard to see without a microscope, I'm pretty sure one side didn't have any solder at all.

@arthurfricchione8119 Жыл бұрын

Another good detailed and informative video. Nice how you found the loose IC. Thanks for sharing 👍

@RobertDotterer 11 ай бұрын

Thank you

@SWTWHITEGSR Жыл бұрын

Excellent video!

@zjeepgozweeln 9 сағат бұрын

Thank you for posting this video. My friend's Ford Escape had the no sound issue. Checked a lot of components on the top to no avail. Found Q201 on the bottom of the PCB. However, instead of 8 pin, it was a 3 pin transistor. Same story though, failed solder, lifting off the PCB. RoHS is great, right?

@9cnfitzgerald 10 ай бұрын

I appreciated this vid fam - have a 14 fusion with ACM problem and was wondering what the board looked like

@RobertDotterer 10 ай бұрын

I am glad the video helped. I have no know idea what each year and model acm looks like.

@RedRooter0828 7 ай бұрын

Going through the same thing on a 2010 fusion. Thanks for the video.

@RobertDotterer 6 ай бұрын

Let me know if you fix it

@ans05 Ай бұрын

Nice!

@x86guru67 3 ай бұрын

I have a 2015 Ford Edge with the 8" touchscreen entertainment center. I'm wondering if the ACM module is similar to this ACM module? I don't have any problems with the ACM module with the exception of there are no line-level outputs from the preamps. It looks like I can see on the left side of your board what looks like a Class D amplifier stage. Would you happen to know if the line level inputs going into those Class D amplifier chips (I assume they are the amplifiers) are easily accessible? I'm thinking about hacking my ACM to extract the line-level signals and disabling the internal amplifier, then just bringing the line-level outputs outside of the ACM so I can provide my own amplification. Let me know if you pinned out that side of the board and what your thoughts are.

@poornavishnu5271 6 ай бұрын

Hi Sir do you know what smd transitiors are used in this circuit board I am missing one I need to buy and replace one is there any options to fix this other than a new smd transistors

@ncsupi Жыл бұрын

This is perfect. I need to try this on my '14 Focus ACM. I don't know if it's going to be the same chip (or if the refdes changed between boards), but I wouldn't be surprised if there's a poorly seated power transistor. I had a year of popping and tripping some resettable fuse or soemthing. And now my ACM is completely dead after a couple of instances of loud, staticky pops.

@andre416 Жыл бұрын

Please let us know if you were able to find the same issue with yours. It would be a big help! Thank you in advance

@ncsupi Жыл бұрын

@@andre416 My board layout ended up being completely different. I never found an amp IC exactly like what you saw, and I found no _obvious_ solder issues, and I gave it a decent once over with our microscope. The two possible indicators I found were a regulator with inconsistent solder on the heat sink, and the weird PTH side mount ICs had a questionable amount of thermal paste in one spot, suggesting inadequate heat transfer. Both point to thermal issues, of course, but are completely different from what you saw. And I'm not even sure the regulator soldering was _wrong_, as it had a grid of holes, some of which were obscured by solder, but some were open. From what I read, that is a strategy used on regulator heat shrinks to actually allow some air flow through it. Seems kinda weak to me, but I dunno. In the end I gave up and rolled the dice on an ebay replacement.

@RobertDotterer 11 ай бұрын

I hope it works.

@ncsupi 11 ай бұрын

@@RobertDotterer Thanks! It mostly does, though Sync doesn't want to answer phone calls right, now, and I did already hear a little pop and hiss once, recently.

@gabrielarchangel1117 Ай бұрын

update: this was exactly what the problem was. i found another ACM for 45 Plus shipping in Nashville. reinstall wasn't bad. just hard to get those clips off and on because they're so hard to reach and maneuver

@joemilana6630 11 ай бұрын

What's that gel you used when removing and replacing the chip?

@RobertDotterer 11 ай бұрын

Conformal coating remover by MG Chemicals.

@jamesferguson822 Ай бұрын

How do you remove the ribbon from the circuit board without damaging it?

@eddiereichel9354 Жыл бұрын

I wonder if the fusion is the same. Had one a couple months ago no sound and got one from wrecking yard and still no sound

@RobertDotterer Жыл бұрын

Some are simular. You just have to test the parts to find the failures.

@johnhutchison9782 Жыл бұрын

Hi Robert. Fantastic video. In your most humble opinion, what is the root cause of this failure? Seems like Ford has an epidemic of poorly soldered chips in their radios, mine included currently. Sony HD with Sync out of my 2014 Escape Titanium. No sound, can't change the stations, can't change the input, CD reads but no sound. I can't believe in this day and age that even Sony brand radios are not holding up quality like they did thirty years ago. Thank you! John

@RobertDotterer Жыл бұрын

Honestly I don't know what the cause is. I would assume poor Solder but you have to also account for all the vibration, heating, and cooling, these modules go through in a car. This type of failure is very common in automotive electronics, especially instrument clusters.

@paulpainter3065 8 ай бұрын

This component gets very hot to the touch when the radio is running. It might be melting it's own solder connection. Hit a bump and it slides out.

@javierpineda6705 4 ай бұрын

Cuando no se comunica el modulo ACM (Audio Control System) verificar que el IC convertidor A1040/e este siendo alimentado en el pin 3 con 5 Voltios

@paulpainter3065 8 ай бұрын

I do not have the magnification level, but to my eye the Q201 solder joints look OK on my radio. I partially disassembled the radio and leaving the bottom and left side in place in order to keep the heat sink connected. With the radio like this, I plugged it back into the car. Once connected and powered up, touching the Q201 component with a piece of plastic caused the radio to start running again. After it ran for a few minutes the Q201 chip was very hot to the touch. I suspect that the solder joint is actually melting with a combination of use and high interior temperatures.

@RobertDotterer 7 ай бұрын

I would reflow the solder and see if it keeps working and the temperature goes down.

@adolfoamoctezuma1978 26 күн бұрын

Yo limpie la tarjeta ACM con dieléctrico y realice prueba . Y el sonido regreso. Por si lo quieren intentar. Saludos

@gabrielarchangel1117 4 ай бұрын

what I don't get is why us there a spot for a 15 amp fuse in the rear fuse panel but Furd decided they didn't need to put one there??

@RobertDotterer 3 ай бұрын

I cannot tell you why manufactures do what they do.

@killianthompson8352 3 ай бұрын

Could I do this without a microscope if not is there another way or company I can get this repaired through?

@RobertDotterer 3 ай бұрын

I'm sure it can be done. It depends on your skill level.

@killianthompson8352 2 ай бұрын

@@RobertDotterer hey I fixed the chip the same way you said and it fixed the blinking clock but now when it plays nothing comes out of the speakers I was wondering if this happens to you or if you know the solution

@Burke396 4 ай бұрын

I've got no sound, crackling noises, and it keeps happening.

@RobertDotterer 3 ай бұрын

I would inspect the board.

@Solairethedarksoul 2 ай бұрын

There’s no way I’m going to be able to pull that off…

@RobertDotterer 2 ай бұрын

You never know unless you try.

@Solairethedarksoul 2 ай бұрын

@@RobertDotterer I took it apart, looks normal. I’m sure I need to replace this thing though…

@pitbullsyndicate93 3 ай бұрын

Water damage

@RobertDotterer 3 ай бұрын

That is not from water damage

@nickayivor8432 Жыл бұрын

👍 SUBSTANTIAL ROBERT DOTTERER My Mentor ROBERT DOTTERER have a great weekend with all your family around you SUBSTANTIAL ROBERT DOTTERER From Nick Ayivor from London England UK 🇬🇧 ⏰️ 18:00pm

@RobertDotterer Жыл бұрын

You too, thank you!