Ford Econoline Vans: Blower Motor Switch Failures Causing Meltdowns!

Рет қаралды 89,434

3 жыл бұрын

In this video we show you the most common reason why the blower motor does not work properly on the Ford Econoline vans 2003 to present.
Forscan is free Ford Specific Diagnostic Software:
Download Here-
forscan.org/home.html
ELM 327 Adapter I Recommend-
amzn.to/2UqDW4v
As an Amazon Associate I earn from qualifying purchases.
My Automotive Repair Shop BSG Automotive-
www.bsgautomotive.com
Catch up with us on-
Facebook: FordTechMakuloco
Twitter: FordTechMak
Instagram: fordtechmakuloco
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user and BSG Automotive (hereinafter “FordTechMakuloco”) makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. FordTechMakuloco shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by FordTechMakuloco and therefore, FordTechMakuloco does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge FordTechMakuloco or anyone affiliated with FordTechMakuloco, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law.

Пікірлер: 170

@brobrio Жыл бұрын

I have a 93 and have this exact issue, except my 1 and 2 speeds always worked. I noticed a smell and saw smoke and knew there was a short. Thank you for showing us this!!!

@Brian-bg2cb Жыл бұрын

Totally made sense and straight to the point. 2000 E250 106,000 miles. You described the exact sequence of events that I experienced in the gradual diminishing of my blower. Racing to beat winter here. Just changed out my totally clogged heater core, so now I gotta get this blower working again. Thanks a bunch!!

@JaMarvelousjmar 3 жыл бұрын

I've learned so much from this guy. It doesn't seem as complicated once he guides you thru the process. Thank you so much and keep up the good work

@markk3652 3 жыл бұрын

This happened to my 2003 Durango. The blower motor resistor failed, so upon disassembly, found the plug in and harness mostly melted. I got replacement parts at the parts store, and wouldn't you know it, the new harness had beefier wire, but every one of them was the same color green. Good thing I have the electrical smarts I do.

@fsu3784 2 жыл бұрын

Got a 2001 e250 and this is exactly what is happening to me. Thank you 🙏

@22howards 3 жыл бұрын

GM Astro does this also difference is, the fan switch is part of the control head 👎. Every car has issues. At least we have videos like this to help us repair our rides 👍 Thank you!

@eliteman7685 Жыл бұрын

This has been a common long running issue…I deal in 72-76 Ford Torino and Mercury Montego cars, and other 72-79 Ford/Mercury intermediates and this has been an eternal issue. I’d love to have a better way to rewire the system running off relays for the high current side.

@williamallen728 2 жыл бұрын

Very helpful video. I was able to repair my van thanks to your thorough instructions.

@twistedwrench490 3 жыл бұрын

As usual great information great knowledge your awesome man!

@josephsfields 3 жыл бұрын

I appreciate your videos. I'd not mind watching the highlights of the actual component remove and replace just in case there are little plastic bits in the mountings and connectors that are prone to cracking or tricky disassembly. Keep'em coming. Ford does make me loco but so does my Chrysler, Buick and Mitsubishi. My only vehicle that doesn't is my 2012 Fuji Gran Fondo 2.0. 👍👍👍

@dannyl2598 Жыл бұрын

Thank you. Once again you have saved the day for me. My switch melted and then melted the knob, it was so hot that the metal shaft burned my finger one the knob came off.

@edman1015 3 жыл бұрын

Brings back memories for me

@joecloud4622 Жыл бұрын

Thank you for you knowledgeable and concise advice!

@andrewjacobson556 3 жыл бұрын

Very helpfull i have a 99 now i know what to look for thankyou!!

@jasont7887 3 жыл бұрын

love your channel. i have a similiar van that the blower works on low and high only and not the two middle speeds. i've replaced the resistor and fan speed switch and still not fixed. this thing is driving me nutty

@ganormand 2 жыл бұрын

Thank you for helping me fix mine. 2001 E150

@RiteSideup-nh6kn 3 жыл бұрын

Every E350 I have on the switch always goes out I finally had a van where the motor went on the fan

@servingme09 3 жыл бұрын

Thanks for info.....now I won't be frustrated with replacement of mind...and why 3 parts are needed.

@manolocordovez9323 Жыл бұрын

Thank you!

@Thecarguy1254 3 жыл бұрын

Looks like the exact same switch panel at my grandmothers old 92 Aerostar, crazy how long they kept some of those parts.

@juancarlos1015 2 жыл бұрын

Thank you so much!! Your videos are pretty informative.

@josevaldemar4587 7 ай бұрын

Thanks again great job

@rodneybrand8521 3 жыл бұрын

That looked good compared to some of the ones I've had to fix..

@AntonioClaudioMichael 3 жыл бұрын

This has definitely been a common problem over the years since the 90s

@johnsegard2948 3 жыл бұрын

Keep up the good work. Thank you.

@ffc3476 3 жыл бұрын

Thanks for sharing Be well be safe

@user-ft3nm1ue2l 9 ай бұрын

That was a great video. My problem exactly.

@joelb360 2 жыл бұрын

Thank you for this video!

@khalidkfy7368 3 жыл бұрын

Thanks

@markf1441 3 жыл бұрын

Good job you look like always ! Respect .

@jesussavessinners123 2 жыл бұрын

Thanks.

@AntonioClaudioMichael 3 жыл бұрын

As always Great Informative demonstration video @FordTechMakULoco

@tompeterson3210 3 жыл бұрын

Another great video!

@hughappleton6480 3 жыл бұрын

Keep up the good work.

@johnviewer2305 3 жыл бұрын

Do you all like my personal ford tec....lol...Brian has his act together fellers....the go to guy....thx Brian...

@pugaoscar Жыл бұрын

AWSOME!

@MrPattyurso 3 жыл бұрын

Don't even own one, but still love to learn. 👍

@RobertKohut 3 жыл бұрын

Nice!!

@PhillyDee215 3 жыл бұрын

Yup, common on these vans👍

@ferminsalas9772 3 жыл бұрын

I wish you would've came out with this video a month ago. This situation happened to my 2014 F150 Ecoboost. Blower burnt also.

@ericgustavson8293 9 ай бұрын

Good video, covers both possibilities. My fan was only working on the lower 3 fan settings, no high. I replaced the resistor, no change. Then I replaced the burned/ melted pigtail & switch, now works perfectly. It's a bitch to get to in a 2010 E150, doesn't have the same easy access panel of the van in the video. Thanks!

@jimmieanderson8263 2 жыл бұрын

i have a fleet of e450 vans the earlier ones i had the issues of melting the switch even with new motro and resistor i ended up running the high through a relay took care of the issues now to be fair i have e450 shuttle busses and have carrier ac units

@drjohnsmythe2968 2 жыл бұрын

That was jacked!

@quicklooksentertainment3217 3 жыл бұрын

Aloha Brian, Thanks for a great video. My 2006 F250 had the same problem. Replaced the resistor and switch but noticed the female connector behind the switch is overheated. I could cut and spice a new female connector but so see you have a Motorctaft Kit there...is the kit the repair for the wires? If so, What part number? Thanks again.

@billyr9840 3 жыл бұрын

Nice !

@RadDadisRad 3 жыл бұрын

Hahahaha, that’s happened to me a couple times. 390k miles on my junk

@boondockingmainahs Жыл бұрын

I have the 2013 e350 and my fan only works on high too ! Do you have the part numbers for the pig tail , resistor , and the switch ? Thanks for the video

@acemobile9806 3 жыл бұрын

Correction, did not stop making them. Still alive and well in stripped chassis form. I deal with this all the time in U-Haul trucks. Standard practice is switch/pigtail/resistor on all of them I come in contact with. I also use Ox-Gard on all connections. The switch is a hopelessly cheap design but is easy to diagnose & change.

@FordTechMakuloco 3 жыл бұрын

Yup I know the heavy duties are still being made but I am talking from the passenger van side of things.

@davidrte.664 3 жыл бұрын

In the 1970’s Fords we had a similar problem with the AC switches, in high blower it would burn the switch up because all the current ran through the switch. We would put a relay so in high blower would be run through the relay. I don’t know how those are wired. But would that help with that setup.

@richardcassinari7026 3 жыл бұрын

Great info...please start including part #s for all parts required to do the repairs...

@FordTechMakuloco 3 жыл бұрын

I always do including the special tools needed for a job unless there is an instance like this that there are so many variations it would be impossible to list parts for every year and trim level. I don't want to mis lead viewers if I don't have the correct info for their particular model.

@DavidBrooksNYC 3 жыл бұрын

i watched this video and replaced everything but the harness !! yeah I'm an idiot!, if you do it exactly the way brian says man you will not have a problem, he is solid on the money

@BeRealAlways 3 жыл бұрын

Do you have the part numbers for each of the items you mention in this video? Thanks

@tiburonrodriguez8902 3 жыл бұрын

I have a question. I have a ford expedition xlt 2004 and the back a/a unit doesn't blow cold air. Also the front a/c goes on and of in all speeds, any ideas can help me out I will appreciate it. Thanks and also your channel help me a lot with my expedition.

@csnr355 3 жыл бұрын

What about if no speed at all, do you think is still the resistor?

@pasteasplaintext 3 жыл бұрын

I have the same issue. No speed works but when I drive on the freeway, I can feel the faintest cool air coming out of the vents.

@N9IWJ 3 жыл бұрын

What would you say if it works on all speeds except high 2011 e350 rear ac fan Thanks very much

@shawncrittenden6216 Жыл бұрын

Well thanks for the Vid but would have been nice to have the Part numbers for the Pigtail kit/Switch/resistor included plus the hardest part of the whole project how to remove the Bezel around/in-front of the switch panel.

@medtec6747 3 жыл бұрын

You also want to check the ground for the BM resistor it's by the accumulator drier often the bolt is very rusted and it can caused increased amperage through the switch

@FordTechMakuloco 3 жыл бұрын

Can you explain how a corroded ground can cause higher amperage pull on the switch? Are you saying the ground adds another load in series with the blower motor? Kinda like the resistors in the blower motor resistor? I would think the circuit would break before pulling more amperage, if it did the bolt and ground wire would be hot and melt in some cases.

@medtec6747 3 жыл бұрын

Didn't mean any disrespect bryan in my experience the increased resistance causes the motor to spin much slower sometimes stopping it letting it sit on one spot on the commutator of the motor passing more amps at a lower voltage than the motor does on high setting which leads to the wires and switch settings for the lower settings to get very hot, also it seems to shorten the life of the BM quite a bit. I may be misunderstanding whats going on but I've had several trucks in the fleet with this issue and that ground always seems to be corroded along with it.

@1artisan 9 ай бұрын

Great video. My problem is the same but instead of blowing only on high speed. mine only blows on low speed. Any suggestions for me?

@jefferyhopcus8300 3 жыл бұрын

I have that exact same van. Can you do a video on how to remove the dash trim so I dont destroy it?

@hotmechanicak 3 жыл бұрын

I have one that continues to come back with the switch melted. We replace the switch, connector and resistor every time. One we even replaced the blower motor as well. It continues to burn up switches. Can you help?

@Iloveorganicgardening 2 жыл бұрын

I just wired my switch so tha Only the high works. But my fan still goes slow sometimes and fast others to others I'm thinking I need to bypass the resistors as well?

@roberttucker68 Жыл бұрын

question is this the same for it stuck in low mode / i pull the knob of and the switch was super hot . or is it a short in the wiring?

@lazaromiranda56 3 жыл бұрын

Hello, I have 2003 ford 7.3 diesel. The speedometer does not work. I replaced the both sensors. What else can I do? Thanks

@tomasgomez9002 3 жыл бұрын

My issue is that the relay for the blower motor on the 2003 blows same blade on the past 3 fuses. sooo...resistor ? Or another issue?

@tlferro Жыл бұрын

Oh how I wished you would have filmed how you took out the panel

@joshbigman1745 3 жыл бұрын

I just fixed this issue on my 08 van. I hit a hump in the road in winter and my blower motor stopped. What I eventually found out is that the connectors to the blower motor and the speed switch were fried, and the blower resistor was corroded. So I replaced all those and then the AC fuse burned up too because the AC relay was soo corroded due to salt and water. So I changed all that and now it works great. Also if you are wondering where the AC relay is, it's in that weird box under the hood right infront of the driver's side. Those relays are not easy to find unless you order them or pull them from a junk yard. It's not the same as the blower motor relay in the main fuse box under the hood. I'm just sharing just incase someone else has the same problem.

@edgar12345632 3 жыл бұрын

Hi do you think using dielectric grease helps to prevent melting connectors ? Thank you for your time to show it.

@FordTechMakuloco 3 жыл бұрын

No the melting is caused by worn contacts inside the switch assembly.

@milcotto4153 3 жыл бұрын

@@FordTechMakuloco - Why would contacts wear out?

@snoopdogie187 3 жыл бұрын

I guess this is still better than the sprinter vans. I worked on one that the blower motor just rusted up and seized. It happened around 100k miles on it and only 4 or 5 years old. This was on a van used almost everyday, as you can tell from those miles. These three parts in this video cost less than that one blower motor also.

@milcotto4153 3 жыл бұрын

I have heard of people having had the blower motor changed on a motorhome on a Sprinter chassis, but they can't get it to work again.

@mrfixzit1019 6 ай бұрын

I have always fixed my own sense I was 14... so I'm no stranger to car problems

@ismaizzy3372 3 жыл бұрын

Yeah

@TheObserver567 3 жыл бұрын

This happened on my 2012 f150. Replaced and used dielectric grease

@TheObserver567 3 жыл бұрын

My connection was on the passenger foot area panel

@eliteman7685 2 жыл бұрын

I'm doing research on the econoline blower fan motor, for upgrading the 72-76 Ford torino blower fan, this is nothing new! Never understood why FoMoCo rammed all the current through a switch. Also seen the full size Chevy vans really suffer from the same issues of control unit burning up and failing. I used to manage a small fleet of Ford Econolines, and Chevy full sized vans.

@brandonc2233 2 жыл бұрын

Is there bulbs in the heater controls?? Mine do not light up at night. Radio, cruise buttons, dash everything else does. Except the heater controls. Kinds erks me because I csnt see them st Nighy so it's a little annoying. I guess I need to pull the Hester control out and see. From photos I've looked at I don't see any bulbs for them. R the dimmer.lights built into the whole unit?

@lonnyharris6464 2 жыл бұрын

What if only low works but not the other speeds? Could it still be same problem?

@precisiont5188 Жыл бұрын

How did you take the panel off?

@lefthander5 3 жыл бұрын

I have also had several that the blower motor(although working correctly) was drawing to much amperage..... change the blower motor if you are repeatedly changing switches.

@FordTechMakuloco 3 жыл бұрын

I have never come across that before in all my years. Was the motor shaft binding when turned by hand or did you compare the amperage draw from another known good econoline in the shop?

@lefthander5 3 жыл бұрын

@@FordTechMakuloco compared to other vans we had.

@10813mike 3 жыл бұрын

Yes that’s a good point. I’m just a home mechanic but just changed the resistor and harness on my 2001 F250 and a few years back on my old 4 runner and both fan motors were tight and seemed to be drawing more then they should so went ahead and changed them both also. Not too expensive for the piece of mind it gave me. Great videos! I really appreciate your detailed instruction!

@FordTechMakuloco 3 жыл бұрын

If this were an isolated incident I would have changed the blower motor also but for the econoline vehicles this is quite common of a failure no matter what year.

@lefthander5 3 жыл бұрын

@@FordTechMakuloco the most common fail for me has been the switch.... we have had a handful of them that would go through a switch every few months and found that the blower motor was the culprit.... and the funny thing is they were not squealing at all.

@britjamaine9229 3 жыл бұрын

Would the same be true for a 92 Bronco?

@pamelamatheny4613 11 ай бұрын

Could a melted pigtail cause the ac to blow off and on intermittently? The blower control switches for front and rear were replaced, but they didn't replace the pigtails. Im not sure if he even looked at them since he didn't pull it out like you did. And worked from underneath it. Replaced the blower motor and the resistor for the front and rear. The front and rear ac goes off and on intermittently.

@ROROSMACHINE 3 жыл бұрын

Former Ford Dealer Tech here, hey I really respect your opinion and appreciate your sharing your knowledge and experiences with us all... I use 5w30 in the summer and the recommended 5w20 during winter fall and spring while operating my 2011 F150 3.7 ltr .... Do you think it is ok to use 5w30 in the Summer seasons ???

@ROROSMACHINE 3 жыл бұрын

BTW I live in Rhode Island (Climate wise New England region)..

@FordTechMakuloco 3 жыл бұрын

I would stick with 5w-20 year round in this engine.

@ROROSMACHINE 3 жыл бұрын

ok thanks

@adriendeboer5798 3 жыл бұрын

Fixed a few hundred of them. Sterling heavy trucks same parts same burnt up parts

@milcotto4153 3 жыл бұрын

That is crazy. Why isn't Ford doing anything to fix this? It is their fault.

@camposvazquez Жыл бұрын

Guys..... I have a 97 e350 class b RV.. When I turn in the AC... Or just the vent... The heater stays on... The blender is working because I can shift from vent to defrost..etc no problem The issue is the heater is always on...even when I switch on the AC... Do you have any suggestions

@wagonwheel42 3 жыл бұрын

Replaced my upper intake manifold on my 2004 f150 and now it won't start but it will turn over getting fuel and spark will the VCT cause this problem it sat for 3 months before i replaced the manifold

@dodgemechanic 3 жыл бұрын

Are you sure you didnt have a gasket fall out or get pinched? Did you miss a plug in for something. Not much else could be wrong if it ran before you changed manifold

@mflip9150 Жыл бұрын

Mine only works on 4 like you said in the video, also it only blows on the floor none of the other settings like vents or windshield work. Would that be a switch?

@jeffhodupp4641 Жыл бұрын

Probably resistor and you have a vacuum problem on other know. Broken vacuum line or vacuum servo

@philh9238 3 жыл бұрын

Should you change the blower motor as well due to high ampere draw?? So the new harness and switch don’t get burnt up

@FordTechMakuloco 3 жыл бұрын

Never seen one cause this in my 20 years of wrenching. This is a common issue with the e series new or old.

@littleblue77 3 жыл бұрын

I replaced all of that and my van still melts . Any advice

@MJorgy5 3 жыл бұрын

Does the rear zone have the same set of issues? If so, where on the vehicle is it's resistor? Thanks!

@keltecfan 3 жыл бұрын

There's a few videos on KZfaq that show where the rear auxiliary heat/AC components are located on the Ford Econoline. I'm almost certain that it's located behind the very rear interior panel on the drivers side rear

@regbrown2110 3 жыл бұрын

Man this is not related to this video but I have a 15 f550 roll back with a 6.8 that has an surge issue nobody around here can diagnose. The a/f ratio pid keeps flopping back and forth . I've replace fuel pump ,fuel pump control module, pcm ,maf sensor ,evap purge solenoid. The intake has been smoked twice no leaks . All parts replaced have been ford parts . Any ideals ? By the way when I first purchased it (82k and recently rebuilt by a ford dealer) would randomly do this once a month now it's an all day everyday concern.

@levijudahmaqabim7123 12 күн бұрын

Do you know why my front vents won’t blow air and the rear vents at the top only blow from max AC e-350 ford van 2014

@john..rutter 22 күн бұрын

Could you send a link to the pigtail

@mrfixzit1019 6 ай бұрын

I already did that and it did it again so what's causing it ?

@davidharris6974 Жыл бұрын

Do you know the part number for just the switch?

@mrfixzit1019 6 ай бұрын

My blower motor is a Chinese replacement from the fan turns where mine gets hot is on high speed...

@tomtheplummer7322 3 жыл бұрын

Bad switch. Thought that’s what the resistor was to protect. Dang.

@blairkennedy7953 Жыл бұрын

1983 ford Econoline. No heat. Dose it have a rester

@rrmech11 3 жыл бұрын

👍👍

@lawrenceirvine8759 3 жыл бұрын

Could you install a relay so the amperage is not going through the switch?

@halleffect1 3 жыл бұрын

that was my thought too but I think it's not easy because of the variable speeds.

@MizzCupcake244 2 жыл бұрын

mine blows low when on high... is it the motor resistor or the switch? the switch does get hot I noticed.

@MizzCupcake244 2 жыл бұрын

I think it's the switch but should I change both anyways?

@MichaelCarter-pq9me 3 жыл бұрын

I have an electrical question to ask you. How can i e-mail you my question

@dodgemechanic 3 жыл бұрын

I've replaced a lot of blower motor resistors on rangers and almost every one I've done the pigtail has been melted/corroded to the resistors. Is there a similar problem?

@FordTechMakuloco 3 жыл бұрын

yes

@dodgemechanic 3 жыл бұрын

@@FordTechMakuloco are the switches the issue in the rangers also or is it the resistors, never pulled a switch out but seen many resistor pigtails melted