Ford Escape headlight removal (2016)//

No video

Ford Escape headlight removal (2016)//

Рет қаралды 88,639

5 жыл бұрын

Another great video resource from #theautobodyguy! How to remove a 2016 Ford Escape Headlight.
#DIY #theautobodyguy #Weekendwarrior #autobodyrepairs
Tools I use:
Milwaukee cordless 1/4 ratchet - www.amazon.com...
Drill & Impact:
www.amazon.com...
Flashlight (I love this thing!):
www.amazon.com...
Video Equipment:
Camera - www.amazon.com...
Tripod -www.amazon.com...
Tripod #2 -www.amazon.com...
Slider -www.amazon.com...
MB01ASGXKMT6VHM

Пікірлер: 40

@RichFarren 5 жыл бұрын

That was one of the better how to videos I have seen. Straight forward, to the point, good video supporting the what’s being said on the audio. Well done.

@Theautobodyguy 5 жыл бұрын

Thanks for the positive review!

@MrCaribe65 4 жыл бұрын

Great work. Getting ready to change my headlight lenses, and this is exactly what I needed to get the headlights off. 👍

@g0osefraba 4 жыл бұрын

After this I will never buy a Ford again. This is almost as bad as changing the battery on the damn thing

@danr2513 3 жыл бұрын

Agree 1,000%!!! I have A 2013 titanium and one low beam bid flickers occasionally and then goes out after 20 minutes. They wanted $650 to replace it.

@wolfendenracing2826 3 жыл бұрын

#righttorepair

@proxypylon Жыл бұрын

Came here to say this

@kevinm363 4 жыл бұрын

how do i just replace the low beam HID lamp only ? 2014 Escape Titanium

@johnmartinez3068 3 жыл бұрын

Great how to video. Do you have a video showing how to replace windshield reservoir on 2016 Ford Escape. Thanks John

@dandrelewis2541 3 жыл бұрын

Thanks for the video, man taking those things out is a pain😑

@maovi7652 4 жыл бұрын

Is it not enough to remove the wheel arch to get access to this last headlight bolt?

@Theautobodyguy 4 жыл бұрын

The bumper cover is the primary object that's covering the side headlamp bolt.

@hangpedos 2 жыл бұрын

Ok so you don't have to pull the bumper cover clean off that's good

@Beth9228 3 жыл бұрын

I used to have a 1998 Ford Contour. I taken out the headlights to replaced the light bulbs. It was held by 3 screws and I used Phillips screw driver to take them out.

@Thatguy01984 5 жыл бұрын

good video thanks. shame on Ford for doing this.🙄

@Theautobodyguy 5 жыл бұрын

Trent Friend right?!

@ryanbassett2091 4 жыл бұрын

What a crap design, thanks Ford!

@wolfendenracing2826 3 жыл бұрын

#righttorepair

@johnanderson6135 4 жыл бұрын

Hi can you tell me how to remove the engine of 2015 ford escape thanks

@Theautobodyguy 4 жыл бұрын

John Anderson 😂 I’m not a mechanic, only Autobody.

@johnanderson6135 4 жыл бұрын

@@Theautobodyguy ok thanks

@paulelester 4 жыл бұрын

Ridiculous process to change the bulb and who has the ford exclusive tools to perform the work

@Theautobodyguy 4 жыл бұрын

Right?! Not a great design

@josephgoode694 4 жыл бұрын

How to replace a headlight on the driver side of a 2016 Ford Escape

@d.beamer6907 4 жыл бұрын

Joseph Goode exactly the same as the video but on the drivers side

@Rtate004 4 жыл бұрын

I just want to change the low beam bulb out. Can't fully squeeze my hand in there so I either need to do this or remove the windshield fluid reservoir to get to it... I would rather not take half the body apart just to change a bulb lol. wtf

@paulelester 4 жыл бұрын

You are correct it’s a complete hassle to change a bulb

@cameronbelway3989 3 жыл бұрын

Ford does this so people will give up and take it to Ford service department!

@newzealandallblacks3726 2 жыл бұрын

Not sure I would describe the headlamps as being easy to take out. You have to take the front cladding off in order to take out a darned headlight. It is the dumbest idea ever! My other car is a Volvo and removing a headlight takes about 2 minutes. My local Ford dealer wanted almost $1000 to replace my HID bulbs and high beam bulbs. Almost $500 in labour!!!!!

@Theautobodyguy 2 жыл бұрын

Craziness

@fsodn 2 ай бұрын

To be fair, this is to replace the headlamp ASSEMBLY. You can replace the headlight LAMPS in a couple of minutes by removing a single rubber cap over each lamp.