Ford Fiesta MK 7 Rear Axle Bushes Replacement

Рет қаралды 3,473

Күн бұрын

Пікірлер: 28

@AlanCooney Ай бұрын

I’ve just done this job on 2010 Fiesta and put a long socket extension bar through centre of old bushes - drilled some rubber while levering my long bar and old bushes came out very easy!!!

@user-kz2rx8yu2f 2 ай бұрын

Nicevone Mark glad to have you back

@ResurwreckAutosUK 2 ай бұрын

Thanks mate yeah had a lovely long weekend away 👍👍

@richardhawkins6960 2 ай бұрын

Hi Mark even though it looked a tough job you made it look easy well done Mark 👏😓

@ResurwreckAutosUK 2 ай бұрын

Thanks mate yeah definitely not a easy job just got stuck it 👍👍

@MrUnderwurlde Ай бұрын

Nice video but I don't think its a good idea to refit the new bushing by drawing it in by the core - you could end up damaging the new bushing. The best approach is to use a cup that is the same size as the outer casing and draw it in that way. There is a bit of a profile on the circumference but doesn't interfere too much with the installation.

@nigelbryant5932 2 ай бұрын

That tool was money well spent. Didn’t look that bad of a job. Will be easy next time. Great to see you back 👍👍

@ResurwreckAutosUK 2 ай бұрын

Thanks mate yeah definitely will be easier next time 👍👍

@richardmounfield7822 2 ай бұрын

Nice work with the new bush tool Mark.

@ResurwreckAutosUK 2 ай бұрын

Thanks mate yeah great new tool definitely be using that a lot more 👍👍

@johnchincotta1qwdb15 2 ай бұрын

Well done Marcus

@leewalerzak 2 ай бұрын

Iv done a few of these nows an hours job once you know what your doing I use a reciprocating saw to cut them out then put poly's in no special tool required

@danielsellers8538 2 ай бұрын

Nice one, budy. Thanks for your vido

@ResurwreckAutosUK 2 ай бұрын

Thanks mate appreciate it 👍👍

@howj4 2 ай бұрын

Good job done

@KerbsideClassics 2 ай бұрын

nice one mark made it look easy mate

@ResurwreckAutosUK 2 ай бұрын

Thanks mate it definitely wasn’t easy but got it done 👍👍

@charliecoco2115 2 ай бұрын

I've seen some mechanics on certain cars having to burn those bushes out with a blow torch.

@keithr3682 2 ай бұрын

Hi mate use a airsaw cut them out and airchle to cut it out

@keithr3682 2 ай бұрын

Sum r metal

@wayneedge4216 Ай бұрын

What size socket and spanner did you use on the re fit tool

@wayneedge4216 Ай бұрын

Thanks

@Toby_the_Glen 2 ай бұрын

Don't forget the threaded bar doesn't last very long. You will be replacing it every couple of bushes! Next time just stick poly bushes in.

@ResurwreckAutosUK 2 ай бұрын

Thanks mate appreciate the info 👍👍

@BRM101 Ай бұрын

No you don’t the threaded bar should meet years mine has

@andrewcreaser4186 2 ай бұрын

Get Yr self a tin of rubber grease .. red stuff and makes jobs easier . Also don't effect rubber like norm grease does . 😮

@MrUnderwurlde Ай бұрын

Not supposed to grease bushings for installation - they are supposed to be a tight friction fit and using grease could cause them to rotate. Best to use a bit of washing-up liquid as that still helps with installation but will will dry off.