Ford Focus 1.6D Oil & Filter Change, Air Filter Replacement

No video

Ford Focus 1.6D Oil & Filter Change, Air Filter Replacement

Рет қаралды 90,300

Күн бұрын

The Ford Focus was due a Oil & Filter Change, this video shows the full proces.
Also the air filter was due to be replaced, which is a really easy job.
Both jobs are possible at home so come on, get your spanners out!
This 1.6 Diesel engine is found in a variety of models, not only ford but Peugeot Citroen, Bmw mini, Volvo D2 amongst others.
Hope you enjoy the video.
Link to all tools and parts used in the video:-
www.amazon.co....
Link to Bosch oil filter £6 amzn.to/3hqTMFV
Link to engine oil £17 amzn.to/3j46riz\
Link to Bosch air filter £9 amzn.to/3j7WfFQ
\
Link to Amazon shop for carb cleaner to dissolve any oil spills, amzn.to/2EGA1Zi
Link to oil drain pan £17 amzn.to/2FRxFuv

Пікірлер: 198

@florodriscoll2354 4 жыл бұрын

This is probably one of the best "How To" videos I have senin a ling time. Excellent commentry from presenter who would give Edd China from Wheeler Dealers a run for his money. Well done again.

@aaanton11 4 жыл бұрын

Thanks Flor for the great comments👍🏻👍🏻🛠

@grez6330 2 жыл бұрын

Absolutely superb 👌, great communication, sense of humour always appreciated, very clear instruction.

@aaanton11 2 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@adamevans426 3 жыл бұрын

Thanks for this, have a 2011 Ford Focus 1.6, everything was pretty much the same and so easy to do. Cheers!

@aaanton11 3 жыл бұрын

Thanks for the great information👍🏻👍🏻🛠

@jenright2069 2 жыл бұрын

That was excellent, a few tricky bits in doing this that you normally do not have to do, like removing the air filter connection to get at the oil filter and the service reset Thanks a million.

@aaanton11 2 жыл бұрын

Glad it helped Thanks for the great comments👍🏻👍🏻🛠

@YutErk 4 жыл бұрын

You actually clear the engine with spilled oil lol. Thanks for excellent video.

@aaanton11 4 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@georgegeorgel7254 4 жыл бұрын

The best socket you can use is the 27 mm deep socket i already changed and it did work like a charm🙂

@aaanton11 4 жыл бұрын

Thanks for the great information👍🏻👍🏻🛠

@cliveanthonytraverse3271 Жыл бұрын

Watched the video twice went out to the garage , nailed it ! Cheers

@aaanton11 Жыл бұрын

Well done, Thanks for the great comments👍🏻👍🏻🛠

@michaelgilbert3213 2 ай бұрын

Well done. Most helpful, I am now confident to do it myself.

@aaanton11 2 ай бұрын

You can do it! Thanks for the great comments👍🏻👍🏻🛠

@Adam-7_7_7 2 жыл бұрын

Thanks mate! I have a Volvo V40 2013 , (identical engine) so I'm watching all your vids

@aaanton11 2 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@cosminanton3901 4 жыл бұрын

good thing all this applies to the Volvo D2 engines, for which there are hardly any videos out there.

@aaanton11 4 жыл бұрын

Yes all the Same, Thanks for the great comments👍🏻👍🏻🛠

@patrickgartnercoelho5628 4 жыл бұрын

Thank you for the video! If this helps anyone and you have a tool that lets you customize the torque; as per Ford, the oil filter (~10:30) should be mounted with a torque of 25Nm

@aaanton11 4 жыл бұрын

Thanks for the great information 👍🏻👍🏻🛠

@andrewjenkins7783 4 жыл бұрын

Thanks for the info; very well explained. Getting my romper suit on this week.

@aaanton11 4 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@manar4809 4 жыл бұрын

Great, straight forward and very informative video. Will be having my first attempt at servicing the Focus soon. 👍

@aaanton11 4 жыл бұрын

go for it! Thanks for the great comments👍🏻👍🏻🛠

@davidwalton4254 4 жыл бұрын

Couldn't be any easier to follow. Thanks for that 10/10 SUPERB

@aaanton11 4 жыл бұрын

Glad it helped! Thanks for the great comments👍🏻👍🏻🛠

@steveyorkshire1797 3 жыл бұрын

Great video,clean,clear camera,all full information for the job given,excellent! "Job's a good'un" !! ...not heard that expression in a while!,great stuff!

@aaanton11 3 жыл бұрын

Glad you enjoyed it, Thanks Steve for the great comments👍🏻👍🏻🛠

@Brynben1 2 ай бұрын

Great video and fantastic tutorial. Gotta have a laugh as well whfn learning 😂

@aaanton11 2 ай бұрын

🤣 Thanks for the great comments👍🏻👍🏻🛠

@davidwebb8877 9 ай бұрын

Good video,easy to follow,mines due it’s next service,it’s on 81k with a FSH,I might do it myself.

@aaanton11 9 ай бұрын

You can do it! Thanks for the great information👍🏻👍🏻🛠

@toneranger 3 жыл бұрын

Great video learned a lot appreciate the additional voiceover and explanations, fantastic, thorough thumbs up 👍🏻👍🏻👍🏻

@aaanton11 3 жыл бұрын

Glad you enjoyed it! Thanks for the great comments👍🏻👍🏻🛠

@noelquigley7822 3 жыл бұрын

Thanks very much for this video! Nice clear instructions made the job very easy. Cheers!

@aaanton11 3 жыл бұрын

You're welcome! Thanks for the great comments👍🏻👍🏻🛠

@j3ll3ymonst3r 5 жыл бұрын

Brilliant video! Very informative and helped me a lot, many thanks!

@aaanton11 5 жыл бұрын

Thanks for the great comments 👍🏻👍🏻🛠

@brir2108 3 жыл бұрын

Good job mate just got the car doing this job at the weekend, will save me a lot of time

@aaanton11 3 жыл бұрын

Glad it helped Thanks for the great comments👍🏻👍🏻🛠

@brir2108 3 жыл бұрын

@@aaanton11 No problem, noticed when doing the job on Sat that there was a small beading of oil at bottom of gearbox, it didn't look red but not sure. Any thoughts? Also I have read that these cars have a problem with the dual mass flywheel have you had any problems?

@robertpalmer5803 3 ай бұрын

Its always a job to get the old filter out of the plastic housing...you have to give it a really hefty tug to get it out...always lubricate the o ring with clean engine oil before u screw the filter in....Bob...Paignton......

@aaanton11 3 ай бұрын

Thanks Bob for the great information👍🏻👍🏻🛠

@maritimeblaster Жыл бұрын

You might want to read the side of the filter. It tells you how to install it. It needs to be installed correctly in order for it to work properly. Never reuse the old old on the new filter. Use fresh oil to seat the gasket. And also once the gasket makes contact it should only be hand tightened to the spec on the filter. Now as far as the vise grips, they damage your handle on the ratchet. Use a breaker bar or a longer ratchet or a short pipe. I feel like some people could get into trouble over tightening the filter or the drain plug.

@aaanton11 Жыл бұрын

Thanks for the great information👍🏻👍🏻🛠

@TheDamiancdk 4 жыл бұрын

Great video mate thoroughly explained 👌

@aaanton11 4 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@markjones595 2 жыл бұрын

Spot on video mate, I'll crack on with mine, if I'm honest a strange place to put an oil filter housing

@aaanton11 2 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@paulrchapman1 Жыл бұрын

Yes, clear, thorough and good humoured. I don’t know about the jacking position on a Focus but shouldn’t you add a stand in the vey unlikely event of jack failure? Perhaps he did but just didn’t mention it.

@aaanton11 Жыл бұрын

Thanks for the great information👍🏻👍🏻🛠

@pauldunne7303 3 жыл бұрын

Very well explained. Going to do it myself for the first time .thanks mate 👌👍

@aaanton11 3 жыл бұрын

Glad it helped Thanks for the great comments👍🏻👍🏻🛠

@grez6330 2 жыл бұрын

Great video Anton, very helpful.

@aaanton11 2 жыл бұрын

Thanks Grez for the great comments👍🏻👍🏻🛠

@leegraham1179 Жыл бұрын

Great video pal gonna do this on my focus now 👍🏻

@aaanton11 Жыл бұрын

Go for it! Thanks for the great comments👍🏻👍🏻🛠

@TarndeepV 4 жыл бұрын

Gonna give this a shot soon, wish me luck and thanks for the video!

@aaanton11 4 жыл бұрын

Good luck, Thanks for the great comments👍🏻👍🏻🛠

@andymoran4095 3 жыл бұрын

Great video, made the job really easy 👍👍

@aaanton11 3 жыл бұрын

Glad it helped Thanks for the great comments👍🏻👍🏻🛠

@mimhopkins8210 2 жыл бұрын

Really well done video even I might have a go I have a2017 Focus Titanium TDCI.Would everthing be the same.The only thing I would suggest Id'e leave the cover off untill finished so you can see from underneath if there are any leaks.

@aaanton11 2 жыл бұрын

very similar, Thanks for the great comments👍🏻👍🏻🛠

@philpavett5974 3 жыл бұрын

Great job,but how about wheel chocks and axle stands before getting under please

@aaanton11 3 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@andrewwhaley697 3 жыл бұрын

Very helpful . Nice clear instructions. Thanks

@aaanton11 3 жыл бұрын

Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠

@luxurydetailcarcare32 4 жыл бұрын

Your videos are absolutely fantastic, you have taught me so much and given me the confidence to do maintenance on my own Focus 1.6 tdci, a quick question, do these engines come with a dpf? I'm not sure how to check on mine, many thanks

@aaanton11 4 жыл бұрын

Yes pretty much all diesels made after 2010 have a def fitted,Thanks for the great comments👍🏻👍🏻🛠

@luxurydetailcarcare32 4 жыл бұрын

@@aaanton11 Thank you very much for your reply, I'm going to use Castrol Magnatec (A5) start/stop fully synthetic 5W 30, I've read others have used it with no probs but also read it's to be used in cars without DPF?

@arturtegze6331 4 жыл бұрын

Thank for this video. Everything been shown and explained 👍👍

@aaanton11 4 жыл бұрын

Glad it was helpful!, Thanks for the great comments👍🏻👍🏻🛠

@kyebuckle4781 7 ай бұрын

Great video, thank you 👍

@aaanton11 7 ай бұрын

Glad you enjoyed it Thanks for the great comments👍🏻👍🏻🛠

@TNSL1111 4 жыл бұрын

Great video, well explained. Thanks

@aaanton11 4 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@philiprobson8016 4 жыл бұрын

Well explained and very clear. Thanks.

@aaanton11 4 жыл бұрын

Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠

@paulrchapman1 Жыл бұрын

Just seen ( after my comment) that this jack incorporates a stand by locking it, so I withdrew my remark. Except to say it does deserve a mention….

@aaanton11 Жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@alanmoore3570 4 жыл бұрын

Great video .

@aaanton11 4 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@fbunt1967 3 жыл бұрын

Nice job. Really useful. Cheers.

@aaanton11 3 жыл бұрын

Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠

@utopiaking6417 4 жыл бұрын

Great explanation and thanks, made my effort a lot more easier, and cheaper, Thanks again

@aaanton11 4 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@lent3oaksdisco 3 жыл бұрын

That’s great man cheers great video

@aaanton11 3 жыл бұрын

Thanks for the visit, & Thanks for the great comments👍🏻👍🏻🛠

@skellingtonGl Жыл бұрын

Thanks Man!

@aaanton11 Жыл бұрын

No problem! Thanks for the great comments👍🏻👍🏻🛠

@dillerud95 4 жыл бұрын

You are a funny one. Entertaining videos are still your skill. I’m stunned. Have a good time

@aaanton11 4 жыл бұрын

Glad you enjoyed! Thanks for the great comments👍🏻👍🏻🛠

@tomsled Жыл бұрын

This is great thank you

@aaanton11 Жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@Yassou1985 2 жыл бұрын

Thank you very much for all you vid about this car ! it helps me a lot ! I am trying to change my fuel injector. Did you made any vid about it ? Thank man !

@aaanton11 2 жыл бұрын

Not yet, Thanks for the great comments👍🏻👍🏻🛠

@foyz1690 2 жыл бұрын

Thank you very much, very informative 👍

@aaanton11 2 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@palespennes4589 4 жыл бұрын

Excellent

@aaanton11 4 жыл бұрын

Thanks for the great comments 👍🏻👍🏻🛠

@WiggysRockShow 2 жыл бұрын

Brilliant, thank you!

@aaanton11 2 жыл бұрын

You're very welcome! Thanks for the great comments👍🏻👍🏻🛠

@paulhickey5794 4 жыл бұрын

Great video. Thanks for sharing. Just saved me £££.

@aaanton11 4 жыл бұрын

Glad it helped, Thanks for the great comments👍🏻👍🏻🛠

@tomszyb7834 2 жыл бұрын

Great very helpful video thanks 👍🙂

@aaanton11 2 жыл бұрын

Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠

@georgegeorgel7254 4 жыл бұрын

When you put everything back in place please just remember to fit the filter first back into the hole and then the cap 🙂

@aaanton11 4 жыл бұрын

Thanks george for the great information👍🏻👍🏻🛠

@fanfeck2844 3 жыл бұрын

george georgel , is it wrong to fit it into the cap first?

@mishutz 3 жыл бұрын

Not really! Filter in cap, oil in the middle of the filter to have less oil starvation on crank up. Just be careful to fit in properly.

@gsf600k 3 жыл бұрын

Very nice video, thanks

@aaanton11 3 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@tompearson6706 3 жыл бұрын

Brilliant video, covered everything that was needed! Unfortunately I've had the yellow exclamation light come on after driving down the road for a bit following the oil change. Any ideas what this could be at all? Possibly overfilled the oil? Message read "service_" I think and the car goes into limp mode. Cheers!

@aaanton11 3 жыл бұрын

re check the oil level, and brake fluid level, Thanks for the great comments👍🏻👍🏻🛠

@michaeldubick9922 3 жыл бұрын

Well explained 💯🔥

@aaanton11 3 жыл бұрын

Glad you think so! Thanks for the great comments👍🏻👍🏻🛠

@michaeldubick9922 3 жыл бұрын

Please but I just finished mine but the engine blog on the dashboard still on

@henrymcdonald6173 Жыл бұрын

It's a 27m socket

@aaanton11 Жыл бұрын

Thanks for the great information👍🏻👍🏻🛠

@wass006 2 жыл бұрын

Very informative, do all diesels need priming or is it just this model of car? Seems like a tedious messy job

@wass006 2 жыл бұрын

Sorry this was meant to be for your fuel filter change video

@aaanton11 2 жыл бұрын

All diesel fuel filters need priming, some are self priming and work better than this model, Thanks for the great comments👍🏻👍🏻🛠

@guilhermeramos2851 4 жыл бұрын

Thanks so much.

@aaanton11 4 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@henrymcdonald6173 Жыл бұрын

Ment to change the filter before put the sump plug back in

@aaanton11 Жыл бұрын

Thanks for the great information👍🏻👍🏻🛠

@Prodavion 4 жыл бұрын

Nice video mate !, only 1 remark, isn't this the type of engine wich had a small oil filter in the oil feed line of the turbo ? And if it clogged, it could destroy your turbo because of low oil pressure ? Is it this type of engine ?

@aaanton11 4 жыл бұрын

I Have not come across this issue on this model, but you might be correct, Thanks for the great comments👍🏻👍🏻🛠

@stevierobinson4055 2 жыл бұрын

Thanks for the video. How do I reset the service light with a start/stop button? 2011 mondeo, same engine. Thanks

@aaanton11 2 жыл бұрын

I will look into it Thanks for the great comments👍🏻👍🏻🛠

@elzrinja365 4 жыл бұрын

Sump of this engine have a big desing flaw Thats why it is black immediately after changing oil.

@aaanton11 4 жыл бұрын

on the other hand if the sump plug falls out, there is a small amount in the base of the sump that might save your engine, Thanks for the great comments👍🏻👍🏻🛠

@elzrinja365 4 жыл бұрын

@@aaanton11 Search this video on YT: "Bundkar modificeres 1.6 hdi"

@drillix5943 3 жыл бұрын

Hi. Great video! On my Ford focus 2010 1,6 tdci, the clamps for the air intake are unfortunately one time use. Meaning i have to go out and by some new clamps when changing it. Any chance know the pipe clamp sizes for the air intake? :)

@aaanton11 3 жыл бұрын

A cable tie will work as it is low pressure, ie before the turbo, Thanks for the great comments👍🏻👍🏻🛠

@rockypup1968 2 жыл бұрын

Quick question , ive got a 2015 connect with the 1.6 tdci , at what mileage should the service lights come on ? Ive only done 12000 miles in 2 years and nothings come up yet , tho ive had a full service done as i didnt want to leave it . Great video's mate !

@aaanton11 2 жыл бұрын

usually 20000miles, Thanks for the great comments👍🏻👍🏻🛠

@rockypup1968 2 жыл бұрын

@@aaanton11 thanks for replying fella

@piecetoyou8285 2 жыл бұрын

Does not make sense to have a sump hole dimpled in` where the bolt goes, So much of the bad bits you need out would settle around the dimpled area, What engineer design this, Don`t understand why oil filter was not taken of be for oil change or does it not matter, Is there a replacement sump that does not have this dimple to where the bolt goes, owe by the way thanks for showing the method

@aaanton11 2 жыл бұрын

Thanks for the great comments👍🏻👍🏻🛠

@TexasScratchMan Жыл бұрын

i dont remember them taking my air box out ever getting my oil changed in focus.. could you still get to it from the bottom?

@aaanton11 Жыл бұрын

Maybe a slightly different engine, Thanks for the great comments👍🏻👍🏻🛠

@evieemaya88 4 жыл бұрын

Gret video anton, what year focus was this ? thanks

@aaanton11 4 жыл бұрын

2012 model I think, Thanks for the great comments👍🏻👍🏻🛠

@Kenny.1979 4 жыл бұрын

Great video mate, just bought a Focus 2014 1.6tdci titanium. I'm noticing when I release the clutch I hear a whining noise sometimes any ideas what this could be?

@aaanton11 4 жыл бұрын

sounds like the gearbox might be a little noisy, you will get a slight noise but if it is really noticeable, its not normal, Thanks for the great comments👍🏻👍🏻🛠

@Kenny.1979 4 жыл бұрын

Either that or release bearing maybe?

@vijayam1 3 жыл бұрын

Sweet! Is it okay for the 1.5/1.6 turbo to mildly whistle post 2k to 3k RPM, a very mild one though. Would love to hear your thoughts

@aaanton11 3 жыл бұрын

you might have a small air leak from a pipe or the intercooler, like a stone chip, Thanks for the great comments👍🏻👍🏻🛠

@samirdjebali2569 3 жыл бұрын

nice video and informative , I noticed the engine on the focus it look similar to Volvo v50 the same oil filter and fuel filter ,i have Volvo v50 2011 the intercooler hose split on driver side I'm having a difficult to have access to the bottom clip to change it . do you have any idea the best way to access it ? thank you

@aaanton11 3 жыл бұрын

Remove the under tray and tackle it from below, Thanks for the great comments👍🏻👍🏻🛠

@samirdjebali2569 3 жыл бұрын

@@aaanton11 thankyou I will give it a try . I did managed to squeeze my hand from the bottom very very tight space

@colinvick8728 2 жыл бұрын

Not sure if I've located filter properly and seal can I take filter out without dropping oil,it screwed right down easily and no leaks

@aaanton11 2 жыл бұрын

Well done, Thanks for the great comments👍🏻👍🏻🛠

@colinvick8728 2 жыл бұрын

@@aaanton11 decided to drain new oil and correct the filter and refill all good now

@kennyball3956 2 жыл бұрын

DAMMIT!!! if its that easy it looks like im gonna hav to do it myself and get my hands a little dirty and save myself a load of cash #noexcuses thx for the vid...great info for all gonna hav to drop a sub ;)

@aaanton11 2 жыл бұрын

Thanks Kenny for the great comments👍🏻👍🏻🛠

@tahirmohammed3008 2 жыл бұрын

I tried draining the oil today on the same car but the bolt doesn’t seem to want to come off, it just keeps turning, any advice?

@aaanton11 2 жыл бұрын

thats not good, the threads must be stripped, Thanks for the great comments👍🏻👍🏻🛠

@itswais77 10 ай бұрын

Oil filter should go in first then you put the cap

@aaanton11 10 ай бұрын

Thanks for the great information👍🏻👍🏻🛠

@rad3k18 4 жыл бұрын

Hi. If I have start/stop button do i have to rest oli change? If yes could you please explain how? Kind regards.

@aaanton11 4 жыл бұрын

are you getting the service message, Thanks for the great comments👍🏻👍🏻🛠

@rad3k18 4 жыл бұрын

@@aaanton11 I haven't changed the oil yet. But i have to. I was wondering how it works after the change because there is no ignition position. Thank you for your answer.

@corrinecummings3538 2 жыл бұрын

It's the glugs that spill the oil. Why can't we have anti-glug pourers?

@aaanton11 2 жыл бұрын

it would be nice😂 Thanks for the great comments👍🏻👍🏻🛠

@shayryan6886 3 жыл бұрын

Hi have u any videos on the auto stop start. I am having a problem with my one it go's in the stop start stops great and then asks for a manual start any idea why its doing that

@aaanton11 3 жыл бұрын

Usually, its when something has broken the cycle, ie removal of the seat belt, or a door opening, you might have a faulty sensor, Thanks for the great comments👍🏻👍🏻🛠

@davidwilkinson7746 2 жыл бұрын

Is this same engine as the bmax and are they any good

@aaanton11 2 жыл бұрын

they are great when they are working lol, Thanks for the great comments👍🏻👍🏻🛠

@tamaskatona9621 4 жыл бұрын

Hello. i'm not sure about the 4.5 liter of oil. Every description I've read says 3.8 litres of oil (Talking about the 1.6 tdci duratorq 84.5 kWh (115HP) from 2011 february till 2014 october). Could your respond to it please ? :)

@aaanton11 4 жыл бұрын

It’s a really easy one, use the dipstick, when the level is correct job done, don’t get hung up on numbers, thanks for the great comments 👍🏻👍🏻🛠

@tamaskatona9621 4 жыл бұрын

@@aaanton11 The problem with the dipstick method is that it takes quite a long time for the oil to drip down into the oil pan. And if you aren't aware, you can easily overfill it.

@koovar 3 жыл бұрын

I followed this to the letter and according to my manual my 1.6 duratorq TDCI takes 3.8 litres, after filling up with fresh oil now the oil light comes on when waiting at lights but goes off when I pull away? dip stick measure is correct whats going on there?

@aaanton11 3 жыл бұрын

if oil pressure light is on at engine idle, you will have low oil pressure, or a faulty sensor, Thanks for the great comments👍🏻👍🏻🛠

@koovar 3 жыл бұрын

@@aaanton11 I rechecked oil filter and it wasnt seated properly so put another one in, now its fine with no oil light coming on, job done.

@marksmith3469 4 жыл бұрын

How do you rate them mark 3 diesel ford focus 1.6 tdci do they have many problems

@aaanton11 4 жыл бұрын

They are as good as the rest, I don't think anyone makes a bad engine anymore, Thanks for the great comments👍🏻👍🏻🛠

@pjohnwilliams6941 Жыл бұрын

Is this the duratorq engine mate?

@aaanton11 Жыл бұрын

its a Peugeot engine, Thanks for the great comments👍🏻👍🏻🛠

@user-970-g3v 11 ай бұрын

У меня Форд смакс такм двигателем. После длительной стоянки, при запуске лампочка давления масла горит 3-4 секунды. Это нормально или нет?

@aaanton11 11 ай бұрын

Thanks for the great comments👍🏻👍🏻🛠

@GearScar 3 жыл бұрын

I'm more shocked about the fact you folks have a 1.6L turbo diesel engine available in your focus, here in Canada, we have 2.0 N/a, or a turbo gas engine in the higher end models, ST, RS, but no diesels, I want a diesel

@aaanton11 3 жыл бұрын

Thanks for the great information👍🏻👍🏻🛠

@user-nq1rd8li5t Жыл бұрын

I thought the 1.6 Diseal had 3.8 litres of oil ?

@aaanton11 Жыл бұрын

keep an eye on the dipstick, Thanks for the great comments👍🏻👍🏻🛠

@user-nq1rd8li5t Жыл бұрын

@@aaanton11 hahaha will do buddy, great content m8, just got myself a mk3 focus so I will be following your channel

@paulomoreira5508 Ай бұрын

Please first take the Oil Filter Element "in"the engine!

@aaanton11 Ай бұрын

Thanks for the great comments👍🏻👍🏻🛠

@TheAsa1972 4 жыл бұрын

this the same as the C20 1.6d 2006 ?

@aaanton11 4 жыл бұрын

yes very similar, Thanks for the great comments👍🏻👍🏻🛠

@TheAsa1972 4 жыл бұрын

@@aaanton11 Thanks M8 iv got to tackle this on the weekend ,Il Subscribe to you

@henrymcdonald6173 Жыл бұрын

Mini is a BMW engine

@aaanton11 Жыл бұрын

Thanks for the great information👍🏻👍🏻🛠

@alanwake3100 3 жыл бұрын

Mate..1 min 3 seconds in, you jacked the car up and went under it but didn't place axel stands.. to all viewers DO NOT EVER DO THIS, that Jack gives way or malfunctions..your dead

@aaanton11 3 жыл бұрын

My jack has a built in drop lock, its a jack and axle stand in one Thanks for the great comments👍🏻👍🏻🛠