Ford Tractor Wiring and Charging System: 2000, 3000, 4000 3-Cylinder

Рет қаралды 36,152

5 ай бұрын

Parts here: farmtractorrepair.com/collect...
Follow Rachel on Facebook: www.Facebook.com/tractorrachel
Follow J&D Productions on Instagram: www. janddproductionsinc
The producers of this free tutorial do not assume any responsibility for accidental injury, death or dismemberment resulting from the performance of any orations detailed in this tutorial. Please be aware of common safety steps--expressed, implied or not expressed. The producers of this video are not affiliated with Ford Motor Company or New Holland.

Пікірлер: 82

@mikecurtis2585 5 ай бұрын

Another great job! And always helpful information! Keep up the great work 👍👍👍

@khadkulyfe7266 5 ай бұрын

you are the best online tractor help very humble

@JasonSmith-vd1sz 5 ай бұрын

Fantastic video, I have a Ford 2000 I’ll definitely utilize this information. Thank you very much!

@christophersiano969 5 ай бұрын

Great video. About 3 years ago, I got fed up with the wiring on my '68 Ford 5000 and as a summer project, my sons and I did a complete overhaul. replaced the points and coil with a Pertronics setup which allows a full 12v to the coil now. Generator and voltage regulator were replaced with an alternator. The location of the voltage regulator was perfect for a fuse box. Replaced all the lights from the headlights to the dash lights with LED replacements. Added LED work lights and LED strobes up on the canopy, so now I have great 360 degree light around the tractor at night- perfect for snow removal. And then, we custom wired everything. I completely restored the rear light which took some significant work as the inside of the lens was caked with 50 years of crud. I also redid the factory dash. I didn't like the replacements with extra light sockets. It also took some work and some careful silicone work to reseal it again. But the restored dash with the LEDs looks fantastic. My youngest son (11 at the time) worked out the fuse values for each circuit. Was a perfect "real world" use of math for him. So, the dash is it's own circuit along with the ignition. The headlight switch, the new switches for the strobes and front and rear work lights are all on their own circuits. A huge automotive connector was used above the fuel tank so that the tractor can easily be split. Also wired in a pigtail so that my Battery Minder charger/conditioner can be easily connected. All in all, the upgrades made the machine far more reliable, the lights are now awesome, and almost everything works as it should. My only issue was that the alternator drives the Proof Meter too fast. As a result, I installed a tach with hour meter up under the canopy to have a true value

@brent212cburg 4 ай бұрын

Dang I wish you had made a video of this. I have a 1966 ford 4000 and I’m wanting to redo the wiring.

@blake8297 5 ай бұрын

Nice video! Love when you work on the 3,000’s

@BrodieBr0 5 ай бұрын

LOL Mice have found the wiring on all of the equipment on my farm tasty at times. As a busy farmer that relies on vintage equipment for all of my tasks, I must drop a thank you for the work you do on this channel. Your videos have helped me quite a few times in the past to get my old stuff going. Happy new year and god bless!

@matzeh442 4 ай бұрын

Your videos helped us a lot. 1000 thanks! You explain everything so well. I love it when Rachel says "2000 3000 and 4000. That sounds so sweet 🤗. Greetings from Bavaria, Germany ✌

@dropbassnetwork 5 ай бұрын

like all you both do for these old fords. so helpful.

@metaspencer Ай бұрын

Somehow y'all always have just the right video for my tractor ... thanks! great stuff and tons of details

@TXMustangGT 2 ай бұрын

Rachel, I remember watching your father on his JD model B engine rebuild video from YEARS ago. Good to see your parents passed on the mechanical savvy knowledge…..Keep up the good work ethic!

@danielriffe1485 4 ай бұрын

Thanks! I just ordered my full kit! Heck of a lot better that messing with the mess of old wires spliced and jumped my the 40 years of previous owners and my self.

@blackymfg7381 5 ай бұрын

One of the best sites for information about this nice old tractors. My steeringgearbox has much play, maybe at some day we will see a video troubleshoot for this to fix it. Thanks for your help

@onetransmission7871 2 ай бұрын

The gear box is adjustable and it's not a hard job at all. Search for it on the net and see what you can find. This is a generic adjustment. Look for an old car, truck, or tractor manual. Adjust the worm shaft first then the sector adjustment. First thing is to inspect all steering components to see if anything is worn causing the excess play.

@marklazarus2584 5 ай бұрын

Thanks for this awesome tutorial video. It will make my life easier.

@bobbyscott8024 5 ай бұрын

Good job y'all! Very thorough!

@qzorn4440 5 ай бұрын

Wow, I can just imagine Grandpa and little Rachel working on a tractor. 🥳 I would like to see a tour in the factory where the new dash and other parts are made. 🐬 I did not see the new dash running in action?

@chrishorton6605 5 ай бұрын

Very good video. Thank you.

@kimballprojects7729 5 ай бұрын

Love my old Ford 2000. Would love to see a alternator conversion kit for these tractors as well.

@jaysee6184 5 ай бұрын

Really enjoy your videos. Would love to see a power steering column rebuild/refresh….❤️our 3000 diesel, hate it’s failing p/s

@redhawk4859 5 ай бұрын

Great Video

@nebiertugrul5095 5 ай бұрын

Nice video 👍🏼

@iqbalshahid7977 5 ай бұрын

Very nice ❤

@crowridge1 5 ай бұрын

Great video….thanks

@iqbalshahid7977 5 ай бұрын

Very nice vedio ❤

@jlawlar 5 ай бұрын

nice job

@annalorree 5 ай бұрын

I don’t have one of these tractors, but I’m leaving this comment for the algorithm!

@williamtowery3586 5 ай бұрын

Awesome thank y’all

@paulprillwitz9901 5 ай бұрын

Do you have a video of changing a generator charging system to a alternator charging system for ford 4000 3 cylinder engines!!

@dj-nr8nm 5 ай бұрын

Is there a tractor make or model that is the most reliable, easy to fix in your opinion (old or new)? Or a couple of models that stand out over the test of time in your opinion(s)?

@mikeprice1816 5 ай бұрын

Can I change my tac. To electronic instead of the cable

@geraldhgiles 5 ай бұрын

Could you do video on a complete wiring on 2n 9n and 8n my 8n wiring was taken out

@clarkhuntley5893 5 ай бұрын

What about positive or negative ground does that make a difference

@bentley1055 5 ай бұрын

Nice

@tubeDude48 5 ай бұрын

At 14:04, those are called Bayonet connector bulbs. At 20:40, it should not be called Yellow/Red, but correctly called Yellow with Red stripe. Same for the rest.

@davidheuvel1879 5 ай бұрын

I decided to replace generator with a alternator do i still need voltage regulator to hook up instrument panel

@dennislong7852 5 ай бұрын

Take the negative battery terminal off test works only for a gasoline

@johnsadler8637 5 ай бұрын

Put a question on your tune-up video from last year, but this one is more current. Do you have a source for a throttle spring for the Holley on a 1968 Ford 3000?

@carlosguglielmelly5751 5 ай бұрын

Rachell genia

@howardbledsoe1204 5 ай бұрын

Are y’all going to have anymore of the premium kits on your sight? I just looked to purchase one and it is out of stock 😢

@iceblue72wot 5 ай бұрын

Hello ! I have a request, many of us have older Fords around the 1960s with Select o Speed, can you show in detail how these work and how to repair and adjust them correctly. There are probably many of these tractors that are unused because people don't dare or understand how to maintain and repair them. It would be appreciated if you could address this thoroughly in future films. Thank you in advance.

@metaspencer 11 күн бұрын

Agreed!

@larrystevens9635 4 ай бұрын

Great job, I have a Ford 3000 diesel, and transmission oil is white from moisture how can I get all that out before putting in new oil. Thanks

@1010109999999 2 ай бұрын

If you look on the bottom of your tractor there is a drain nut for that and then there's one in the middle on the side of the tractor that's the fill up just keep putting gear oil in it until it goes clear then cut your bottom nut and fill it up until it starts coming out that side nut you're full you're fresh you're finished❤

@RobertFredman-ld6kc 5 ай бұрын

Are you guys familiar with farmtracs

@falarequestretvjorgecarval4263 Ай бұрын

Hi Rachel.and Dan . Two questions . I have a Diesel Ford 5000 1- where is the hidraulic pump ( have no power lifting hay bales ) Where can I get a manual for the F 5000

@antoniorojas8460 17 күн бұрын

Hello lets me thanks so much for your videos and also you father ls a master I iam a owner of a ford 4000 diesel 1972 and its a four whel drive i have this equipment in costa rica central america carring palm oil fruit in a farm I love so much this much this machine

@michaelburdosh6431 5 ай бұрын

Kove your videos. I would like to know if you sell a rebuilt carburetor for a 3-cylinder gas 2600 ford tractor

@user-rb8mo8mu4q 5 ай бұрын

The teens wondered what was kept in the red shed on the far edge of the school grounds.

@sjsjdhdjdfbdbdnsndbd9531 3 ай бұрын

Hey I have a ford 3000 how can I figure out what year it is

@paulprillwitz9901 5 ай бұрын

👍👍👍👍👍

@kossgroupllc9196 5 ай бұрын

All my tractors are industrial tractors (MF-202 and JD 302A). Will you ever do any videos on them? I know that my MF is close to a TO35 but I don't know the ag version of the JD302A (do you know?). Also, I made the mistake of buying tractors that needed new rear tires- so I need 4 14.9-24 tires. 2 years ago, these tires were $400 ish a-piece so I put it off. Now they're going for $800-$1200 a-piece. Surely there is a way to not spend $3200 and get some tires (and no, new tubes won't solve this. Any ideas? Would love to get your advice!!!!

@ShainAndrews 5 ай бұрын

You learned a lesson the hard way. Everything increases over time. Odd ball industrial tire sizes especially. Step into a Carlisle. As for industrial... highly doubt there is much if any difference beyond implement accessories. There was another import tire brand I've heard of... but can't remember at the moment. It will probably come to me when I stop trying to remember it.

@hpniemi 5 ай бұрын

I have Ford 4000 and it has a dc generator. . When I start the engine, the charging light stays on as long as I increase rpm enough. The charging voltage is still only 12.5-13v. The generator is rather new and so is the regulator and wiring. I was wondering are these dc generators just so lazy... Many people have upgraded to ac alternator taken from a car...

@ogunugurlu9034 5 ай бұрын

Hello, I have brake and hydraulic problems for my Ford 3000. Can you help me with just information?

@user-fk8qz9wj4l 5 ай бұрын

Yes, with pleasure

@user-fk8qz9wj4l 5 ай бұрын

ارسل رقم الهاتف كي اتواصل معك

@ogunugurlu9034 5 ай бұрын

The hydraulics do not stay at a single setting. Do I need to replace the valve seal for this?

@ogunugurlu9034 5 ай бұрын

Ok, I will replace all the gaskets. It doesn't lift adjustable, it only lifts or lowers it straight.

@ogunugurlu9034 5 ай бұрын

Sorry to bother you again. Ford 3000 hydraulic brain has a spring next to the press valve. Does it need to be removed in all of them? This bow is missing in some videos, thank you again

@mnblkjh6757 5 ай бұрын

🤔is name change permanent or temporary?

@danielglaus2064 2 ай бұрын

F 1700 wont shift help

@eugencatlan7949 Ай бұрын

Bună am un tractor ford 3000 și nu mai am turații la acul de la priză când calc ambreiajul, se poate face vreo modificare?

@chuckfinley4757 5 ай бұрын

Next video will be how to repair a 'tachometer' on a Ford 3000.

@a.s.c.2909 5 ай бұрын

It’s not a bad idea to use dielectric grease on all those electrical connections before you plug them in. Keeps corrosion at bay so ten years down the road when the ignition switch needs replaced, it all unplugs like it was new.

@user-fk8qz9wj4l 5 ай бұрын

Find a Ford 5610 tractor engine

@markamcampbell5795 5 ай бұрын

you had me until you said to pull the battery cable off while running to test the charging system. you put a voltage spike through the system and could burn out some parts.

@stephens7107 5 ай бұрын

Won’t the voltage regulator prevent a spike?

@markamcampbell5795 5 ай бұрын

@@stephens7107 that is what would get burned up as well as the lights and gauges.

@ianrobinson9565 5 ай бұрын

This test at 4:45 of the video does not prove that the regulator is functional. It shows that the field and dynamo wiring is intact, but does not prove the electrical operation of the cut-out, and the voltage and current relays. The voltage shown is only armature residual which on a lucas generator is 2 to 3 volts. Try fixing components instead of replacing them.

@wiedietie 5 ай бұрын

Merry me 😍

@frankc1430 5 ай бұрын

You can do a load test without a load tester. Just hook up your volt meter to the battery and crank the engine over and watch your voltage. Poor man's load tester.

@jdubya54 5 ай бұрын

A true load test is checking the cranking amps. The tester creates a dead short pulling on all the cranking amps available. You can have a battery that wont crank a tractor but enough voltage to turn on lights or a radio etc.

@jdubya54 5 ай бұрын

Or show 12 or more colts in a tester

@frankc1430 5 ай бұрын

@@jdubya54 The load from your starter is your draw while you watch the voltage drop on the meter. Even a caveman can do it!

@frankc1430 5 ай бұрын

@@jdubya54 Out of all the years I've been an automotive I've never seen a battery load tester that test amps. They always test volts. Only time I ever seen anybody doing amp draw test was to see if a starter was bad.

@jdubya54 5 ай бұрын

I never met a cave man before. Lol

@onetransmission7871 2 ай бұрын

You absolutely cannot check an alternator by disconnecting the battery cable while it's running! If your regulator loses ground a good alternator can put out 100 volts at high rpm! Headlights go off like flash cubes. Internal alternator wiring looks like burnt shredded wheat, etc. I'm in central Indiana. If you want to learn mechanic work and pay me a small but reasonable wage I'll drive up there and teach you how to rebuild engines, transmissions, differentials, carburetors, starters, alternators, generators, electrical diagnosis etc etc. Somebody could get hurt and/or cause serious damage to their equipment if they follow your videos.

@Nox-px3dk 2 ай бұрын

I’m commenting so I can see who’s right. I’m not educated on this so I would like to know. :)

@onetransmission7871 2 ай бұрын

You can't just generate current. It has to go somewhere. That's where the load comes in. Alternators and generators are rated by Amp output at the specified voltage. Testing equipment on the bench or vehicle requires a carbon pile to load or drop the output resistance. If the voltage regulator is working and voltage is at the specified range Ohms law says amperage will increase and that's what we need to check. You can disassemble, clean, and play with an ohm meter but you won't know if it's going to perform. When it's done properly you might show 40 Amps @ 7+ volts for 6 volt system or 14+ volts for 12 volt system. You have to produce more than nominal voltage to overcome resistance in the wiring and the battery itself. Even Harbor Freight has a load tester than can impose a quick load on your charging system. This is the electrical equivalent of an engine dyno. You put a load on it at operating rpm to check the output. Stator windings can actually be checked on the bench when disassembled. Connect a battery and Amp meter directly to the windings just for a second.3 wires have 3 ways to connect so there are 3 test combinations. If you read 60 Amp draw its output will be 60 Amp. 90 Amp Alternator will have 90 Amp draw etc.