FormD T1V2 Long term Update!

Рет қаралды 8,520

Күн бұрын

Here's an extended update for the FormD T1V2.
As an Amazon Associate I earn commission from qualifying purchases, thank you for your support of the channel via the product links.
Component Links:
Case: FormD T1 2.0
Motherboard: amzn.to/3uJlVRz
CPU: amzn.to/3ecXzu3
CPU Block: ModUltra Lobo with "Wave" Heatsink Cover
Pump:
Rad: amzn.to/3Eq28ff
Rad fans: amzn.to/3ecXzu3
RAM kit: amzn.to/3JJzGUE
PSU: (This is the link for the white one) amzn.to/3edacFD
GPU Block: amzn.to/3MgHkIV
Fittings: Phanteks Glacier
M.2: amzn.to/3uJTZNw
amzn.to/3OgZFGr

Пікірлер: 16

@dylanguerrero8053 10 ай бұрын

Just built in the T1 and watched all your previous videos on it. So it's a nice surprise to see an update!

@_antoniocouto 10 ай бұрын

Finally! I've been waiting a long time to see a review of the Next Case

@ghost-type 7 ай бұрын

I just ordered this case last week. I'm excited to get it in. This will be my first mini ITX build so I'm excited and nervous, but luckily there is a lot of content like this that is helping me get my build ready. I'm still gathering parts so I hope to start building my start to mid Jan.

@herculesperseus6326 10 ай бұрын

Can't wait for the experiment on the T1 reference! Thinking of migrating my 5900x and 3070 build into the case and having a reference point on that loop with a 280 would be greatly helpful

@theb4r138 10 ай бұрын

Love that case. I’m running a 240 and 140 rad and it’s great. Pain to build with two rads but the performance is there

@rmartin987 10 ай бұрын

Have you thought about doing a video on upcoming products/parts you are interested in? Like T1 V2.1, M1 EVO, monitors and such. Keep up the great work

@JDLMCLOW 10 ай бұрын

Loving all your sfx builds. Did a build in the meshlicious after watch your builds, with a 5600x and 2070 super full custom soft tubed. It was ......... interesting getting it all to fit, but decided for external 280 push- pull config. with a external pump on the rear, may have to try my evga 380 latter on, but may not fit.🙄🙄 looking forward to your next build.....👍

@k0rnd4wg69 10 ай бұрын

Lobo gang

@robertmorrison4020 10 ай бұрын

I got a sliger sm580 and I wish I was able to put another radiator in my case. The Jonsplus i100 is the only case I have seen that's a sandwich style with top and bottom 360 rad support. Pretty expensive too. There's always a ghost s1 but that unobtanium if you want dual rads.

@chiefgulGreece 6 ай бұрын

Awesome as always!! Can i ask you a few scenarios because i am in a dilemma thanks in advance. 1) Can i Air cool the ryzen 9 7900 non x or x using the formd t1 sandwich layout? Or it would be better of getting the reference (whenever that's available that is) using the noctua C14s (in your video you showed some very satisfactory low temps). 2) Or i`d be better of getting the Ncase M1 evo paired with the noctua C14s or the Silver Soul 135 which would give me much lower temps. 3) I prefer air cooling systems because i haven`t used AIO before but if i were to use AIO (not custom tubing etc) which ones would you recommend? The itx build i intend to build is primarily for rendering stuff and then gaming thanks again

@rockyyz89 10 ай бұрын

had this lian li psu for a week and returned it because of constant "howling" under load when the fans are really spinning, changed to the cm sfx 850 gold, way better in terms of acoustics

@nguyen918 10 ай бұрын

Does the DC pump sut in top of the LoBo block? And I'm assuming you're topping of the system without a reservoir?

@MachinesMore 10 ай бұрын

Yup, DDC sits on top and then the heat sink cap goes over it. It wouldn’t be a good idea to top off from the pump block since you would potentially leak coolant from there when you open the port. The flow indicator when the case is flipped upside down is the high point, so I try to get all air bubbles to collect in there, and then top it off from there. Pretty safe location.