Awesome work on a subject that nobody covers and most of us dread doing! This is becoming the most informative channel on KZfaq, for the Foxbody community. Thanks and keep rockin’ the content- this stuff helps!

I learned that red Pex water line works amazingly well as a door striker bushing on my '92. The ones from the Help section were too thick.

Not a waste of time at all I appreciate you taking the time to explain.

Thanks for all your high quality and top notch videos!

I really like the way that You show and explain how to adjust the doors on the Fox body ! Thank You . 🇺🇲🇵🇷🦊👍

Good advice..The preload is definitely a good tip..

“Excuse the dad bod I hear they’re in Now”😂😂😂Great Video

It’s a night and day difference we had a drag roller with cut out door panels for the roll bar crash bar etc the doors were super smooth and light weight

Great video. Thanks.

I went through this same thing hanging the doors on my ‘66 Mustang. I set the door up empty and then had to re-align them once I got the glass in.

I appreciate the video, just got a new door and this is helpful.

Love the vids keep them coming, great advice.

door preload is a good idea. i just swapped the doors on my 86 capri t-top car. i put 87 convertible doors on it and they don not fit the same as the 86 doors. im going to go ahead repair the factory doors and reuse them. the driver door may not be repairable. we'll see.

Great video! I really appreciate the your effort to get this information out.

Good info, and that door closed perfect

Have you ever hung a GT Convertible door bu yourself? Would you be able to guesstimate the weight of the door fully dressed? The tip about the dorman hinge pins is great. Do you have video of the door being removed with 1 person? Ty so much for the content - I just stumbled on your channel and am thankful for it.

Can you please do a video on installing the front fenders and getting them set right thanks! Great vid btw great input!

Love your content! Right to the point and detailed. Question? Is that the 5 gallon paint stick or standard 1 gallon stick.

Fresh haircut 💈

My doors were sagging replaced door pins now door has a gap if fully closed can't open from outside.. after looking closely door hinge bracket is bent out driver side

You’re doing a great job!

Thanks for all the great suggestions! I appreciate the part numbers. What chemical / brand do you use for cleaning the door latch mechanism?

Another great video, my passenger door sticks out just a hair when shut even with the striker all the way in. I might try the 2x4 trick, like I said it’s really close just off enough to annoy someone with OCD like me 😂

Before removing doors is it best to drill an alignment hole through the hinge into body so that you can reinstall with proper alignment…. I am about to remove mine as part of a total rebuild and paint job

Move the door up, down, forward... But what about in and out? I've got my fender and jambs MINT but there's like a 1/4 where windshield/roof meet. You guys shim the bottom out or something?

A impact screw driver that you smack with a hammer will take those screws out of the latch mechanism every time. Probably buy one for 20 dollars or less.

I'm 27. Restoring my first complete shell of a 89 notchback and the doors the people put on it before I bought it fit like complete hell. Full of bondo and tweeked as shit. Gonna be sourcing some good ones, thanks for the tips.

Good content, thanks👍🏿

Subbed👌🏾👏🏾🙏🏾

Dope stuff man !

Where are you located, I’m in Virginia Beach, Virginia?

Hey Aaron. Koz from base. Hit me up!

You never actually said how to align the doors is there some kind of alignment tool or what?

So did you pay for it to get wired up. Or when is the wire up video coming?

I'm gonna have to take my driver's door off whoever had it before me said the door was sprung back the other way I hope I just have to replace the door and hinges

So the doors are coming off again? By pulling the door pins correct?

Its backwards...