Рет қаралды 158
#TayPro25
Frame: Lumenier QAV Pro 2´5"
Camera: CADDX BABY RATEL 1.8mm
Antenna: FOXEER Lolipop 3
FC/ESC: MAMBA F411 25A AIO
Firmware: Betaflight 4.2.2 Tuned
CONTINUE CURRENT: 25A×4
Motor: MAMBA Racing 1404 5000KV
Propeller: Gemfan 2540x3 Flash
VTX: MAMBA TX400 set to 25MW
VTX Antenna: Iflight 150mm CL
AUW Weight: 249g :)
Lipo size: 4s 850mAh R-Line Tattu 95c
TX: TBS Tango2
RX: TBS Nano Crossfire Receiver
FPV: Fatshark Attitude V5
HD Action Cam: Insta 360 Go2
Modifactions: DIY 56x RGB LEDs glued on the ducts and
controlled via Betaflight and TX switch
Arrma #BigRock aka #Biggie
FEATURES:
-Stronger chassis and retained hinge pin plates
-Steering with more clearance for stones
-Castellated slipper pad and sliding gear mesh
-15T Pinion
-1.1 inch wider stance for better handling and bashing
-Plastic locknut for slipper
-23T Spline servo saver
-37T 1.35Mod diffs with silicone O-rings
-Power Module with sliding gear mesh and improved dirt management
-Rubber shielded bearings throughout
-Oil-filled shocks with silicone O-rings
-Wider arms front and rear
-Body with matte black finish
-Front and rear bumpers with matte black finish
-Tough black multi-spoke wheels with matte black finish
-Vented multi-terrain dBoots® RAGNAROK™ tires
-BLX100 2S/3S waterproof* ESC
-IC5™ connectors (EC5™) compatible
-Signature easy-access modular design
-Easy-access power module
-Easy-access electronics module
-Easy-access diff module removal front and rear
-Double wishbone suspension front and rear
-Metal-geared differentials
-Adjustable ride height
-Adjustable body mounts
-Adjustable turnbuckles
-High-speed center driveshaft support
Wheelie Bar
-50+ MPH (80+ km/h) speed achievable in optimum driving conditions on 3S LiPo
-Stock Wheels, Ragnarök or from Louise MT Spider 2.8 14mm but with imbalance!.
My #PiperPrint & McGyverStyle Tuning:
Self design BullBumper
Selfmade Middle Brace with TPU damper and Green lights.
Motor Spacer Mount, for the gab between the main Plate and Motor in TPU.
TBS Race Wire lite LED for the Green Glowing Eggs.
DIY Standalone FPV System with a Runcam nano Racer 2,
Forious Nano Stealth VTX connected via Pushbutton on 12V direct.
LED Stripes 12v Green-side LR, Red-rear, Purple-front.
Headlight 2x 3watt LED on a stepdown set to exact 3.3volt with a toggle switch.
Waterproof Snap button from a old Flashlight as a main switch.
HD Cam Mount selfmade design for Gopro, Insta360 Go2 and more.
Greenstripes DIY cut out from green duct tape.
Green Protectors printed in TPU 95A.
Green Wheeliebar Wheels, printed in TPU.
Green and Black Labels printed in TPU.
4 more infos or interesting things, visit us on Facebook:
4 the small Drones and quadrocopter with FPV
HomeRacer
/ 1489754187984836
for smooth cinematic footage
#CineWhoopersGermany
www.facebook.c...
or meet us here in Real life to fly together on
RC & FPV
/ 876403579113342
greets #OliFPV
Music: Tomorrowland 2023 - Best Songs, Remixes & Mashups - Warm Up Mix 2023