There is so many things wrong with this video. No new parts. The bearings in the 3 phase motor... just replace them.. but then dont hammer on the outside races. You can HEAR how bad those bearings are now when they powered up the motor. Nothing was replaced, nothing was refurbished. The teflon tape was backwards in half the shots, then there was teflon put onto the clamp nuts for the air lines.. they dont even hold air pressure. This was... terrible. The motor sounds horrific. The sounds it was making are the sounds you hear when you should be replacing the bearings PROPERLY. Yea, this was terrible. They didn't tighten the belts. The preload adjustment on the compressor bearings... which were assembled dry..... no overpressure valve... reciever not tested... the list goes on. I wouldn't have this thing within 100 meters of me.
@MrJosevintemАй бұрын
I love when they paint bolt threads or when they put too much teflon tape and backwards ahhahahaha so beautiful.
@ewanbaxter919911 ай бұрын
I have to disagree here - restoration means to restore back to new, NOT just strip down, paint everything then rebuild as a lot of these "Full restorations" do. This has done absolutely nothing except make it look pretty. I saw the cylinders were still rusty, the crank journal was rusty, same bearings re-used, same piston rings re-used, pistons rusty - in fact nothing was restored except the gaskets and changed the oil. For what good this has done there was no need to strip it down, he could have just painted it assembled.
@larryclifford892811 ай бұрын
Show um,,partner,,,,Show them.
@interesting790610 ай бұрын
@@larryclifford8928 He's totally right, this did more harm than good, not only they didnt replace anything, but painted on the races, studs and the bore too! They replaced 1 seal, but then they use that gasket material that is used to make shoe soles and will start to leak in a couple of weeks use.🤣 Was a good vid though.
@user-yh6dr9jn4x10 ай бұрын
Да им пох на нас, на Вас и на этот компрессор😅
@williegillie571210 ай бұрын
@@interesting7906 I’ve seen dry engines run before. So much damage is done until the oil reaches each moving part. Assembly lube is very important. I give the guy credit for getting to run.
@gsxrsquid10 ай бұрын
Looks like one of those shops in India or Pakistan. Painted all the surfaces that should not be painted. Didn't ever rebuild the valves. In the old days we used those compressors in hospitals. We would tear them down every six months. Once you clean them up if the springs are still good you can flip the valve plate over and use them again. We would replace rings and valve assemblies annually. I might use that gasket material on a LP steam line but not on a compressor.
@aries25846 ай бұрын
yellow, blue, black,orangeand gold different color i like it😍😍😍
@andycnm11 ай бұрын
No washer on wheel axle, split pin not properly fitted. Air receiver welded and not pressure tested (or safety valve). But the biggest sin is no gland fitting on the motor or electrical boxes! 3 phase wiring going through a hole with sharp metal edges. A air compressor on wheels will shake a lot and it will not take long to ware through the insulation and kill soneone!!!! bad news
@dtrestoration859011 ай бұрын
Thank you!!!
@jfjjjjfj11 ай бұрын
Yep, and the banging on the outer race of the bearings, ouch. Why not paint it better when all that effort is made? The motor sounded really bad, or what was that noise when only the motor was spinning? Would be nice with a pressure test of tank, we don't know how rusty the tank is, or if the safety valve even works. And last, it's going to overheat because no fan for cooling the cylinders. Unfortunately just a another "youtube-paint-it-video" 😢
@tamta21927 ай бұрын
Cái này là dành cho mấy bạn thích màu mè, và không biết gì về máy nén khí xem ^^
@user-cz2ex7pv3z6 ай бұрын
السلآم عليكم تحياتى لك من المغرب اتمنا لك الازدهار
@Stardust_170110 ай бұрын
ベアリング圧入で外輪側を叩いちゃダメでしょ。 あれだけで転動面のダメージ有るでしょうね。
@interesting790610 ай бұрын
What I would call 'asian redneck' -style. Wearing dress shoes while spray painting, the dog getting high on paint fumes, and nothing other than a bad paint job was done to the compressor which will work just as good or bad as it was before. 🤣
@josesirleicassemiro290510 ай бұрын
Falta muito detalhe, não limpou os pistão, não trocou os anéis, não bruniu as camisas, não limpou( lixou) a ponta do eixo onde coloca a polia( volante), não lubrifica as camisas para montagem, não gostei nota 4
@helihonda10 ай бұрын
Do not hit the outer race when driving the bearing. Let's hit the inner lace
@denniswray589411 ай бұрын
I have been a mechanical engineer for 40 years and never ever stripped a 2 r s bearing re greased and refitted, always replaced said bearings,
@sergijezagorac428110 ай бұрын
For what good this has done there was no need to strip it down, he could have just painted it assembled.
@paulc.cowanjr.949910 ай бұрын
Why even start it. No pre lube on ANYTHING. No torc wrench on the cylinders or piston rod bolts.
@thetai2291Ай бұрын
I think the temperature of motor is very high when running
@HenryShiley11 ай бұрын
Hmm.. @1:43:30 the sound of chipped bearings, yay.. Maybe @1:31:25 you could have reinstalled them without hammering the outer race around.. use a tube on the inner race and a press.. I'm sure you could make a press with the stuff you find.
@ccris50410 ай бұрын
Machined surface such as cylinder or threads, shall not be paint to avoid leak failure. and pets should keep clear out of the factory while painting, and welding should keep clean, to be free of dirts,dusts and paint, or weldings to be done before painting, and lubricants as grease should apply during pulley and shaft assembly.
@dennismoore377311 ай бұрын
you need to use oil when you reassemble
@dtrestoration859011 ай бұрын
Thank you, watching video!!!
@johnk360610 ай бұрын
No need to bother when you are going to put the bearings back together with paint all over the races and are not going to clean gasket surfaces from paint before assembly. It may work for a while but has been life limited by poor assembly.
@johnwsinkankas604311 ай бұрын
Piece of krap in (re-built, WTF ?? ) Piece of krap out......
@philoupaulo10 ай бұрын
Paint on shit equal clean shit just like in the navy...
@anthonytanzi10 ай бұрын
that motor sounds not happy, probably the way the bearings were installed. I would of tapped them down on the center race not the ou side of the bearing. it sounds like the bearings are not seated
@bpetnoi147210 ай бұрын
Worse than a "sloppy so called restoration" is the assembly procedures. Who in their right minds pounds on bearing using the outer race over a shaft. That is OK if you are putting them in a recess but totally wrong for installation on a shaft. I never saw the tank being pressure tested. If it was really rusty on the inside it might fail under pressure. Compressed air is much more dangerous when it fails as compared to a hydro test.
@raulgarduno785011 ай бұрын
IS NOT RESTORATION IS ONLY CLEANING AND PAINT 😬😬😬
@TheHansvabel10 ай бұрын
all the electric is really bad. he has no clue what he is doing.
@aadilfarooq58384 ай бұрын
Good job ❤❤❤❤❤
@JeffScylla8 ай бұрын
Sure... just take everything apart, wash it in diesel, then spray it all as colorful as possible and put it back together. It doesn't matter that the rusty cylinders and old rings remain, the more colors, the merrier.... Videos are really made by everyone who has a hole in their ass. :))
@rennie16139 ай бұрын
This was just so wrong, I’m speechless.
@RestorationVideo11 ай бұрын
Great recovery, Thank you for sharing how to restore the device. I also do this job. Looking at you today, I learned many things. Congratulations and best regards 👍🤝🙏🇷🇺👈
@jesusemilioposso722110 ай бұрын
Perdone .oero para mi no me gusto en muchos aspectos .no lubrico el cigueñal ni los casquetes de las bielas , dknde asientan los cilindros no se pinta .y si sigo no tengo cuando acabar .mejor dicho perdi mi tiempo viendo este video .es mas el titulo esta erroneo .si gusta lea los comentarios de personas q si saben q es restaurar un compresor o cualquier otra maquina .
@user-dd1qh8by6h11 ай бұрын
Рестоврация для музея😂, а не для работы.
@AdventuresRCZ9 ай бұрын
Piston rings, bearings and bushes need to be replaced otherwise you’ll have problems
Looks like that compressor has been commissioned for COCO the Clown and his clown car workshop 😂
@karirkedua502610 ай бұрын
terimakasih ilmunya, sangat bermanfaat
@sergeyyurchenko48211 ай бұрын
You didn't install washer on wheels, the stopper will broken.
@larryclifford892811 ай бұрын
I would like to know did the compressor work? I see the motor run,,,yet did the compressor itself do what is was built to do?
@stuartgemmell496610 ай бұрын
This not a restoration, just a clean up and paint job. The biggest mistake is no inspection or testing of pressure vessel and associated pressure relief valve. If no valve fitted as original a suitable valve should have been installed. Very poor show.
@franktrujillo93487 ай бұрын
I totally agree with you
@steveg4iwr8 ай бұрын
This is a repaint not a restoration.
@erezyoal10 ай бұрын
Wtf man ? Put back the old barring ? Noooooo
@johnhamann525710 ай бұрын
It looks like Dad needs to teach his son how to paint. I'm guilty also, Dad needs to wear earplugs and a dust mask. Love video. John H, Minneapolis, Mn
@MrJosevintemАй бұрын
It is the new Lidl Compressor.
@riccardocairoli93955 ай бұрын
Incredibile. ,non ha sprecato neanche 1 ml di W40 per sbloccare una qualsiasi vite o perno!! In compenso ha abusato del martello !!
@mohamedseghir636211 ай бұрын
You didn't install washer on wheels, the stopper will broken
@williegillie571210 ай бұрын
The only thing I wouldn’t recommend is dry fitting the parts together. Assembly llube works great. Nice job I hope it runs well.
@HN-gj9zv8 ай бұрын
good job
@canaldogonzo10 ай бұрын
Rapaz, pintar primeiro pra depois soldar, mel delz!! Isso foi a porquice do século!!
@stuartdavidsonR369 ай бұрын
This is a comprehensive video of what NOT to do 😔
@SchnickSchnackSchnuck.9 ай бұрын
Sounds like an old coffee grinder. Sorry, bad work.
@rrotwang11 ай бұрын
Great video Brooklyn ny
@user-kh9os1iw3x7 ай бұрын
Доктор Дью уже все сказал за меня, насчет вот таких реставраторов.
@kbn6366 ай бұрын
Bravo god video, men sir de lavet nogle slemme fejl men ellers ok.
@manuelalvespedroso4579 ай бұрын
Já li alguns comentários,está tudo dito,nunca vi tamanha inconsciência no que está a faser,nota 2para as juntas e pintura,esse Sr devia de ter vergonha de mostrar um vídio desses.
@alro243411 ай бұрын
'restoration' is hyperbole, 'full restoration' is just a lie.
@user-ln1fn7rv5t10 ай бұрын
계속 보고 또 봐지네ㅎ
@miketowne92068 ай бұрын
As long as it works when done , who cares iwhat it is called
@MoteurenColere10 ай бұрын
Devilbis Made in France
@markmawson17 ай бұрын
Well you really don't know how to use a tig welder do you? You weren't stick welding lmao
@Farm_fab10 ай бұрын
Welding over paint is not a good practice. The welding should have been done before the painting, then the welds wont rust as quickly.
@mohamedseghir636211 ай бұрын
You did a good job, but when you put the pieces in place, you didn't put them in the right place(washer)
@76Russian_medved.11 ай бұрын
Это видео уже было на другом канале неделю назад
@TgWags697 ай бұрын
Alternate titles: -Birth of the worlds first Anime Air Compressor -Clown Compressor Compendium -Bad Bearing Bonanza -Paint a Pig and Call it A Pork Chop All of these would be a better description than "restoration"
@richardautry959411 ай бұрын
Painting over those surfaces was a pretty rookie looking thing to do, as was using a. claw hammer to cut that gasket material.
@Farm_fab10 ай бұрын
Using a hammer to cut gaskets is not a novice way to do it. I've watched many mechanics in business for decades use this technique. It's actually a pro move. He should have cut all the way through the gasket with the hammer, and then he would have not needed the scissors for the cylinder bore. A ball pein hammer is more effective, and he should have spread the RTV in the middle of the gasket, not the inside edge.
@lesterabram55467 ай бұрын
Awesome job guys. Now I can restore mine.
@mpalaskokkalis14768 ай бұрын
Perfect 👌
@user-hc8fs4ry1o8 ай бұрын
Es un esfuerzo grande mucha inversion en tiempo y dinero quedo con mucho ruido el motor tocaba la helice plastica del ventilador en la chapa tiene un par de defectos pero en terminos generales es un buen trabajo
@stanisawk138510 ай бұрын
39:56 tu trzeba małego młotka ale o końcówce w kształcie kulki, wtedy uszczelka się sama odcina i jest gotowa
@user-cr7bw3zv7m7 ай бұрын
修理屋ではなく塗装屋です。修理目的ではありません おもちゃ色に塗るためだけの分解です。修理のスキル有りません(We are a paint shop, not a repair shop. It is not intended for repair; it is only disassembled to be painted in toy color. I have no repair skills)
@johnk360610 ай бұрын
Unless he removed the paint from the sealing surfaces of the cylinder and head, what was he thinking.
@khanhle12829 ай бұрын
Vô nghĩa chẳng làm gì ra hồn vòng bi mà đóng vòng ngoài là không biết làm rồi hơn nữa cắt miếng đệm quá vụng về
@jacquesdejeux99226 ай бұрын
Sale boulot !!!!!!
@Rollingcalamities9 ай бұрын
Need to invest into a sand blaster😊
@yvesj.278610 ай бұрын
This is a very bad way to mount the ball bearings on the rotor. Il is needed to apply the force on the inner, but NOT on the outer. Now the ball bearings are out of order and noisy as the test shows. It need to be remplace ball bearings for a long service.
@mrsunelectronics54410 ай бұрын
Ich hoffe Ihr habt daran gedacht, die Zylinder mit Hitzefester Farbe zu lackieren ! wird sich sonst verfärben 👆 werden heiß 🔥( Auspuff od Ofen Farbe nehmen)
@JohnDoe-es5xh11 ай бұрын
Nice restauration, but the belt guard is still missing.
@davidturner86897 ай бұрын
It is strange that so little was done to repair the unit. Perhaps it was just to present it looking better. I don't know.
@Farm_fab10 ай бұрын
One thing i would encourage you to do is keep your pets out of the area when you are either removing paint and rust, or painting. Dusts and vapors are not good for them anymore than it is for humans.
@tigxxl10 ай бұрын
Has anyone seen this damage on the tank when they cut off the base and why didn't they sand it and check the pressure? Why weren't new pistons and rings installed, no one retracted the cylinders, and the old corroded valves are a joke!!!
@SamTheSum11 ай бұрын
But does it work?
@robertk94909 ай бұрын
Co to za regeneracja jak wszystko złożone na starych częściach, nic nie zużyte. Słychać jak huczą łożyska w silniku, ciekawe czy wlali nowy olej do sprężarki czy ten stary.
@jakub778 ай бұрын
hello men, where you forgot WD40???
@CARCULE-gn4xe8 ай бұрын
Tipo de video que não se aproveita nada!
@loelloel65827 ай бұрын
assembly of orange wheels without washers? weld painted things 🤦 In that case, you need to weld the brackets, sand and paint and then use screws or rivets for the joints...🤦 I'd rather not watch because I don't want to see what they'll do with the engine.. 🤦
@user-ig6ze6mj4j6 ай бұрын
😇👏👍
@user-ml1yz5rb8g10 ай бұрын
Не надо писать что ресторация обойму конусного подшипника не красят и в старые литол не кладут да ещё и на двигателе барну перекручивают за кадром камутация треугольником была а потом вдруг звездой стала
@frankschwartz740511 ай бұрын
What the hell? I didn't see any engine. I was expecting to see a combination engine/air compressor. (there is such a thing) There's a big difference between an engine and a motor.
@2TRestoration11 ай бұрын
Very Good
@rosevaldosilva626511 ай бұрын
Gostei muito obrigado;
@alvarogameplays400910 ай бұрын
Eso no es una restauracion oara pintarlo y cambiarle el aceite no necesitaba desarmarlo Una restauracion es canbiar los anillos metales baleros reacondisionar cabezal ETC, ETC .QUE DESEPCION
@paulfellows209411 ай бұрын
fantastic restoration mate those magic hands worked there magic perfection well done
@basilbasileus721110 ай бұрын
Abonat.👍
@leszekl20239 ай бұрын
A teraz warto wpisać w wyszukiwarkę "compressor tank fail"😂
@robertmason83417 ай бұрын
Wtf kinda tig spot hip hop pop and lock weld job was that? Didn’t replace/restore anything other than a good clean up really. To the inexperienced eye might look nice, to anyone that actually repairs stuff they see right thru this. And why do a lot of these restoration channels paint stuff to look like kids toys using bright as colors? Put a nice industrial/machine tool grey/silver on it and it’ll present much better IMHO at least. But seeing as he was able to take it apart correctly and assemble properly, for the most part, I’m sure he knows enough how to actually restore it properly if he wanted to and it wasn’t just for a video. So I’ll give it a B+. Better than the average person would probably do not excellent work though! 🤷🏻♂️
@jt94987 ай бұрын
Wasn't even a good cleanup! Very sloppy job all around. Made it look like a toy with all those silly colours! And didn't show in the end that it even filled with air!
@josesirleicassemiro290510 ай бұрын
Como diz o ditado a tinta tampa todos defeitos, aparência 10, mecânica e detalhes técnicos muito a desejar, nota 4
@moacirsouza831510 ай бұрын
Muito bom , organizado, sabe o que está fazendo, muito cuidadoso, nota 1000. Muito instrutivo.
@frankmartin79229 ай бұрын
знает свое дело? на сьемнике лапы переставить не могу, можно было сделать его двухлапым и снять шкив. Передний корпус подшипника колотил молотком, хотя там есть отверстия, куда надо вкрутить болты и крышка сама снимается.
@williamwilliams81457 ай бұрын
So a full restoration is stripping, cleaning, let someone who is color blind choose the color scheme and paint it, then put it back together again with all the same worn out parts and not pressure testing the tank.
@user-sb4er9wc6u7 ай бұрын
피스톤링. 압축링은 바꿔줘야지 그렇지 않으면 수리할 이유가 없는데. 베어링도교체하고
@jacquesdejeux99226 ай бұрын
Encore un mécano "fantoche" les roulements sa ce change et surtout ont ne les frappes pas car il sont marqués sur le chemin de roulement et donc "HS" a bon entendeur !!!!
@randy633411 ай бұрын
I watched the entire thing. An excellent job by a serious mechanic. A Master.
@victorsosa561310 ай бұрын
Como que vi unos cambios en la conexión electrica😂
@karlcanal72063 ай бұрын
What chemical's or detergents do you use to wash the parts
@andrzejporeda72819 ай бұрын
Przepięknie jest to odrestaurowane ta stara zabytkowa pompa a dlaczego ten smar do łóżysk wygląda jak kupa pozdrawiam serdecznie 👍👍👍👍👍
@leszekl20239 ай бұрын
Ten smar jest odzwierciedleniem tej całej naprawy ten kompresor się nadaje do postawienia i oglądania jak w muzeum ale gość o tym wie i nie pokazał manometru podczas pracy .
@Cidronek10 ай бұрын
ballbearings no goods
@Toruk_Makto_RU10 ай бұрын
Потрясающее рукожопие. А потом обижаются, что люди говорят: "Китайское -- значит, некачественное"