God job! Now this truck hopefully will run next 5 miles without any problems.

Афигенный ремонт .балку в чермет.отверстие под шкворень прослабленно ,да ещё и коническое .во время езды шкворень размолотит эту хрень очень быстро.

На пару дней, если не часов...

ما شاء الله عمل جيد انا متابعك من المملكة المغربية الشريفة سلام

If ever " bodging " becomes a Olympic event these people are guaranteed " GOLD " it takes years of practice to get to that standard,

Интересный народ! Вот они думают,что набрав такой чудовищный пакет рессор ,все остальные узлы автомобиля тоже усилились? Я конечно, понимаю,что буддисты верят в последующие реинкарнации после смерти,но зачем искусственно приближать ее приход?

Should be able to get at least another 2 bags of cement on that truck now.

You have to admire these guys, give them a stick Welder and a handful of basic tools and they repair anything

If they can make that, even work for a short trip, why do manufacturers bother with tolerance 😅

Я в шоке... За 20 лет работы главным механиком, даже представить не мог что такое возможно 😂

😂самое главное покрасить или вернее скрыть косяки😂😅

Одно знаю точно - водиле не позавидуешь.

These guys are a bunch of hacks, but that repair is acceptable.

If you're only welding it, why not leave the axle on the truck?

Yeah. But they didn't show the best part.....how they honed the busing bore out with some gravel and goat lard. Got it real smooth

Урок, как делать нельзя 😂😂😂

one of the few places in the world were you can over load a truck by 500% fix it by the side of the road and just dive off afterwards with out having it unloaded and scrapped and the diver cited but saying that these guys are making do with what they have . i have some car repair books from the 1910 ans 1920 and they would do the same thing but with gas welding . so these guys are the bomb

Сварщик конечно супер,я думаю если ещё налетит с грузом,то теперь не выдержит балка.Теперь ездить надо аккуратно.

seems that it would have been a good idea to grind a vee to get deep weld penetration, do weld with a pin in place so that the hole stays relatively true. It amazes me that all these videos from that part of the world are characterized by extremely limited resources yet at the same time pushing machinery to ridiculous limits as a normal. You would think they realize the need to go easy on equipment.

اتمنى لكم الصحه والتوفيق انكم اصحاب خبره شكرا ❤

Lástima, no es la forma correcta de hacer la reparación pero cada quien hace las cosas a como sabe y con lo que tiene. !EXITO!

Muito bom o Trabalho, solda com muita profundidade.

He was doing so good up until the grinding

That happened due to overloading the truck..And this repair will not stay for a long time

chuc ban co co nhieu VIDEO hon nữa HIHIHI VIỆT NAM

I'd love to see this pull into a chicken coop here in the US. The looks on the DOT inspectors would be priceless.

Nelle condizioni che lavorano e l'atrezzatura che hanno a disposizione sono a dir poco GRANDIOSI

Son unos genios reparan todo lastima la desprolijidad

Gettin the job done ✅👍😊

'Fully *overloaded* front axle' is a more accurate description.

You have mastered your craft

Excellent videos ! 👍

Great job

Why not just buy one from a wreckers that’s not broken ?

Aguanta esa soldadura en la punta con carga?

I guarantee this truck is way overloaded. No rules there. Nearly all these “ repairs?” lol wouldn’t be allowed in many countries. But it’s amazing what these guys can accomplish with basic equipment and hard labor. Nothing is to spec but they get it done.

Вот это мастера,отремонтируют и восстановят самую сложную поломку.Уважение таким людям.Спасибо за видео.

Wa . Do like that very risky job Ground not solid enough to hold the truck load Very Dangerous to risk doing this repair job

KEDO SORPRENDIDO YO DE ESTE TEAM COMO TRABAJAN EN CORDINACION Y ADEMAS SABEN DE TODO AL TODO .NADA LES FALLA LE BUSCAN SOLUCION Y... LA ENCUENTRAN 😂😂😂😂😂

Heat it with a torch take all the heat treat out so it breaks worse next time

GREETINGS FROM GUATEMALA CENTRAL AMÉRICA I'M MANUEL.

You, people, are genius!!!

Во, придумал ролику название: ремонт звездолетов на Татуине!"😂😂😂

I pretty much agree with the previous comments. Just adding that the truckers are probably making more than enough money to cover their overloaded truck repairs and if they didn’t break down from overloading, your “fix it” shops would be out of business. I’m in this to take in just how the parts can be given extended life by great people. While I don’t have the skills to do this repair type repairs, I can use the approach on minor repair projects.

Best weld job yet,usually they don't bevle it

Пацаны ваще ребята. Не ну умеете,могёте. 👓🍿

This is how people get killed on the roads!!! It’s not like you don’t have another one laying around or can’t get another one because they still make them. Th8s is exactly why you don’t ever ever do this!!! Showing this here just proves to everyone else around the world that you guys can’t fix anything to save your life.

Надеялся до последнего, что отверстие доведут хотя бы на фрезере/токарном. Хотя, уже немного смущало отсутствии трещотки в начале видео.

Overloaded Hino truck.

Will this still hold after repair, since the truck is still overloaded?

Lesson from these videos - don’t buy used trucks in these places without a top to bottom inspection……these drivers overload by an astronomical amount and the ‘most used tool’ is a hammer

That is a very scary fix. Sigh.

Man darf nicht länger als zwei Sekunden am Stück schweissen. Danach den Schweisspunkt mit Hammerschläge entspannen. Am Ende Entspannungs Glühen. Gruss aus den Alpen.

Must be a challenge to get spare parts in this country. Would be interesting to load one of these jobs up on a press to see how much load it can take before and where it snaps Just for a test. With the amount of load these guys are hauling on their equipment they may as well make custom axlle with 3 inch kingpins to match spring packs with 20 leaf springs and chassis rails 3 in one. May as well double up on shock absorbers too !! Goes to show to what extremes these worker have to go to keep these vehicles rolling under the punishment that they face.

Super

Доктор, на сколько хватит? Приходите еще😂👍

I wonder if this will last long

Of course the truck suspension fails because it’s designed for 15 tons not 50 tons .Beside the truck definitely damages the roads too .

What a great repair NOT!

Looks like Birmingham

Great job fellas. You do admirable work and I’m certain this repair will last for the life of this vehicle. I trust your knowledge, experience and talents. 👍🏾

Туфту сделали! Шкворень пролетает насквозь, не задерживаясь! Хватит тысяч на пять км, потом шкворень разобьёт проушину, и хорошо, если водитель не пострадает, дай то Бог!!! По нормальному, балку под замену без разговоров!! Хотя, смотрю этот бедлам давно, вижу, из чего они запчасти делают ( Аля Китай во время культурной революции, в каждом дворе по доменной печи) и не удивлюсь, если и новую запчасть не надолго хватит... Это ж надо, балку пополам ломают, ПОПОЛАМ, Карл! Я однажды налетел на отбойник, то у меня балку согнуло, но ни одной лопины, а здесь на ровной ( сравнительно ) дороге балка пополам!!! Смертники!!!

It’ll last……until the next workshop on its travels.

The kingpin must be an interference fit in the beam. If it's right, you need at least a 15 ton press to remove it. If its loose like this, it will turn in the beam and not in the bearings. That is absolutely deadly. People who do such kind of death trap repairs should rot in jail.

should get through MOT.

That front axel will fail again. The weld is only a surface weld and does not have a deep enough penetration to hold adequately. I suspect the next video we see of this vehicle is when it is in a serious accident.

If OSHA was involved with this, the violations would fly..lol.

7018 ? From Brasil

At best this is a bush fix and nothing more. I can appreciate the effort but... will it work? for a little while. will it fail? absolutely. most likely in spectacular fashion killing someone for sure.

if they didnt ABUSE their trucks every mile they travel with 50% more than its made to haul, they wouldnt need to fix them all the time.the mechanics should raise their prices accordingly.

nice job ok, but why did the front axle broke, because the idiots of drivers or company bosses overload the trucks

Да, да, да, мужикам респект, из говна и палок делают говно и палки

Неужели эта сварка выдержит нагрузки многотонной машины?

Wish I was on a percentage on all the stick welders sold in Pakistan.

Long live cheap labour. That repair will cost $35 thousand dollar in US.

If these vehicles weren't overloaded to the excess in the first these repairs wouldnt be needed, also that front axle would of been heat treated from the factory by welding and heating most of the strength will be gone and more than likely fail again and possibly killing someone. I was taught you can pick two of the following Cheap, Good and Fast but you won't get all three.

In our next video, wheel flies off of truck and kills 8 people.

eles boto o dobro do peso nada aguenta na mão dedes quebra tudo

what is this?

Another endless hack repair that will keep coming back. No matter, plenty of welding rod always available as well as grinding wheels.

Зачем разбирать, проще сварного позвать....

Good

Трудяги они.но не оборудования не инструмента.все кустарно.

Дурдом. Это во первых часть ходовой , металл перегрели , заварили. 1000 км проедет и развалится . Столько рессор - фиг с ним рессоры выдержат дикий перегруз а чулки , балки , подшипники? Диски ? Шины? Ребята по хорошему балку чермет

Hmmm... I didn't see them Normalize the part. Heat Up the Whole Area around the Repair to about 400 Degrees and Burry it in the Sand and leave it for Several Hours sonit Not Bridle

👉 👍👍👍 🇧🇷🇧🇷 BRASIL

Перегруз мешками впечатляет более ремонта, но ожидал развертки хотябы на станке о верстий. С другой стороны нужда не тетка.

wish i could weld 1/10 as good as these people

Ну думаю раз сваркой по внутренней прошёлся значит 100% на станке поправят поверхность, заодно и опорную плоскость для подшипника. Ага, хрен там плавал, болгарка и гравер. 🤦‍♂

Déjeme decirles que todo eso es tiempo perdido eso no se puede reparar eso no aguanta los tres primeros huecos que caiga y se vuelve a reventar

А то больше не приедет! 🤔🙆👏👍😂😂😂

Это перегруз полюбому

At 5:52 he said dang that's hot baljeet

Absolutely no goat sex slaves were harmed in the following wreck of this truck.

Bahi mobile kon sa hy name plz 🇵🇰🇵🇰🇵🇰

No reamer, that is the sloppiest king pin fit I have ever seen.

Mechanic beats his wife. Then he lays pipe.

If you just stop overloading those trucks! The chasis is not up to the job, the brakes are not up to the job, and the engine is not up to the job! But greed dictates otherwise!

Our side specializes in selling isuzu, hyundai, hino trucks and packing according to request, hope you support and develop the channel

Fully loaded how about Overloaded