Future Fins one shot and a new router

Рет қаралды 1,000

Күн бұрын

First time for me today installing a Futures single fin box with the One Shot system. A new router to play with too!
Music with thanks to 'Olexy'. Check um at - www.pixabay.com/users/olexy-25300778/ --------------------------------------------
If you wanna check out memberships there is a ''join'' button on my channel or you can click this ere link - / @smallkinedings
Once you sign up, you'll wanna join this super secret members only facebook page - / 966305518417568
You'll get first look at new videos before they go public and we can go over your own repairs through that page as well.
There are always members only videos being posted up on youtube too which only you members will have access to.
---------------------------------------------

Пікірлер: 33

@thefilthygringo9228 2 ай бұрын

Love your videos, very informative. Futures fin box installation along with Nut placement while re-locating a leg back into the pelvis. Thank you. Keep up the good work.

@smallkinedings 2 ай бұрын

Appreciate it, glad you enjoyed!!

@jimdow6470 9 ай бұрын

Your workmanship is always a pleasure to watch, as are your presentations. Thank you. I like the Futures centre finbox, as the fins are almost always perfectly vertical without buggering around. When I glass mine, I sand the top off the box first to allow a full thickness of glass right to the edge of the slot. It stops the difficulty you mentioned re laying the glass into the hard corner. I will try you method next time, as my method requires careful sanding of the box without cutting into the board. Something I have done on numerous occasions.

@smallkinedings 9 ай бұрын

The box sat so well with that flange, the dummy fin stood perfectly verticle easily! Definitely with a repair, I usually would've sanded the box flat once it was installed, before I laminated it. Was interested to know how the glassing would go though as the next one I do will be going into a fresh blank

@t00lshack 9 ай бұрын

Ohh jeeze that story at the end, mercy pains for that dude.

@smallkinedings 9 ай бұрын

Dude... the worst, can't even imagine it!

@familyjay5636 9 ай бұрын

Can't believe his mates ballsed it up so badly!

@allsurf 9 ай бұрын

Great video as usual. I may make a jig for routing a Futures long box. Does that router have a dust collection port? Didn’t see one. I have a Porter Cable plunge router that does which I really appreciate. 🤙🏼🐾

@smallkinedings 9 ай бұрын

@@familyjay5636 😂😂😂😂

@smallkinedings 9 ай бұрын

@@allsurf yea, now that it’s in my hands doesn’t seem too hard to make. I think Andrew W has a video on making them. I haven’t watched it myself but sure I’ve seen the thumbnail. The router does have a dust collection fitting that I’m yet to try but definitely will on the next one

@largepinewings 9 ай бұрын

En route to brighter futures 😉😉😉😉😅

@smallkinedings 9 ай бұрын

Clever, I should have titled the video that 😂

@chriscoralAloha 9 ай бұрын

This is great. I recently purchased the same router and jig. Thank you for the Run through. You rock.

@smallkinedings 9 ай бұрын

O, nice! Have you used them yet?

@chriscoralAloha 9 ай бұрын

Sorry for the late reply. I was waiting till I had a go at them. Yes. Worth the money. I was using a home made jig. This is much better. I also like the Ryobi router. So far. @@smallkinedings

@Jim-fe2xz 9 ай бұрын

I've only built one board & used a guide I found online about 2010. I struggled with the little details like glassing over the fin box and getting the glass to conform. Your thorough explanation of everything including the small details is greatly appreciated! I made it for my daughter but it took her years to ride it for fear of scratching or dinging it (LOL) but she loves it now. 🤙

@smallkinedings 9 ай бұрын

Nice man, the ultimate compliment when it comes out so good she's afraid to scratch it 😂

@H2OSURFDESIGNS-tv8pg 8 ай бұрын

Love your work.. tip for you on the router depth setting. turn the router upside down place the jig on the base of the router and then take a fin box also turn it upside down and place it next to the router bit and set your depth. use the depth stop to set that the router only goes that far down. hope this makes sense.....

@smallkinedings 8 ай бұрын

That is certainly the method with the laminate trimmer but I think that would be pretty difficult to do with the plunge router?

@H2OSURFDESIGNS-tv8pg 8 ай бұрын

@@smallkinedings yes true but you should have a depth stop on the top side of the router, some have a micro adjustment as well. i set my cutting depth then lock the router on the side with the locking clips. then i turn the depth stop on the top side till it touches. then the depth is set and when you plunge you cant go past that set depth.

@Andy_XT 9 ай бұрын

Yes, it is a useful video. Again. Your dexterity, though, makes everything look simple. I am quite sure I would benefit a router with a round base. Or, with a base like your Ryobi, I would probably have to use it turned by 90 degrees, so that the flat sides would be in contact with the guides.

@smallkinedings 9 ай бұрын

I was a bit concerned about the shape of the base as well but did some testing and even if rotate the router almost 90 degrees it still drops the dowel straight down onto the marks

@allsurf 9 ай бұрын

Typically, a rounded base is recommended so that dust doesn’t impede the movement.

@chriscoralAloha 6 ай бұрын

Ok. 2 months later I can tell you your tip of sanding down the edges of the box before glassing is the go. Thank you .

@smallkinedings 6 ай бұрын

Yea, have dine a couple since and it definitely makes chasing airbubbles a non issue! Actually gonna send that to futures as I'm sure they could do that in the cnc process

@surfgeek 9 ай бұрын

I have never tried a speights , I will have to keep my eye open for it if we get in this part of the world

@smallkinedings 9 ай бұрын

Sample, not a bad beer. Nothing hipster or fancy. Just a normal bloody beer 😂

@nada4490 9 ай бұрын

Thanks :)

@smallkinedings 9 ай бұрын

Thank you!

@6to6surf4 9 ай бұрын

Great tutorial, would you recommend buying the jig as oppose to fcs? cheers

@smallkinedings 9 ай бұрын

Cheers, glad it's helpful! For longboard boxes like this one I would definitely go with the futures kit. Everything you need all in one box (aside from the router) where as FCS you kind of have to hunt down all the individual pieces and I found there really isn't any support or guide lines on how the system is supposed to work