The fact that engineers could come up with this is incredible.
@irombeach2 жыл бұрын
I thought exactly the same thing.
@TheVenom83435 жыл бұрын
I'm absolutely blown away by how complicated a 4L60E is!!! I rebuilt the 5R110W in my Ford diesel truck and it was nowhere near this complicated. I was actually surrprised by how simple it was. And it has 6 forward gears even though it only uses 5. Great work my man, great work!
@DonerOfTheDead663 жыл бұрын
KZfaq DIY videos usually drive me nuts, too much time spent with nonsense talking. Not here, straightforward no banter, great camera angles and great close up explanations. I appreciate your work. Rebuilding my second 4l60e, the first time I danced between videos annoyed till I found this series, this time went directly here.
@brandonmessing46845 жыл бұрын
Who else didn’t know automatic transmission were this complicated... oh my
@MrClarkisgod5 жыл бұрын
And now you know why they charge you $2700 for a trans rebuild.
@TheVenom83435 жыл бұрын
You ought to see inside of a 5R110W out of a Ford diesel truck. It's much more simpler!!! I was actually surprised at how simple it was and it's got more gears than the 4L60E...
@KM-tg1mc Жыл бұрын
Yeah. 1 seal wrong or clearance bad. entire transmission failure.
@19914runner5 жыл бұрын
Your patience is amazing...this job would get old real quick if I had to do it. Props to you man!
@ronsteelable94055 жыл бұрын
This boggles my mind. But I'm glad you researched everything and converted it in to video format. Can you do a manual transmission rebuild one day?
@FuzzyDiceProjects5 жыл бұрын
No manual trans rebuilds planned at the moment, but we would like to do a video covering one in the future!
@Gnat0085 жыл бұрын
Massive upvote for the Tom Servo reference! I love MST3K. :D The amount of parts in these transmissions is just mind-boggling!
@Thompsongs5 жыл бұрын
I was very happy about that reference.
@deankay44344 жыл бұрын
Nice catch on the servo apply pin burr and how to remove. This another one of those normal things not found in any service manual or book. Nice job again!
@deankay44344 жыл бұрын
I wanted those who watch, but read comments to know, the Corvette apply piston is a better part than the original and commonly reasonable. For a higher apply pressure, I choose the Superior brand Super Hold Servo and 4th apply piston kit that comes with a billet cover. It has 30% more apply pressure than the Corvette type. Not bag or good, it comes down to how much does a guy want to do or spend. It is the old saying; “It cost money to go fast, how fast can you afford to go?” Great job again.
@Thompsongs Жыл бұрын
14:28 that MST3k reference still makes me very happy.
@Damage42X5 жыл бұрын
I really hated it when I rebuilt my transmission (same 4L60E), but now watching this video I really want to rebuild one again.
@1301407gl5 жыл бұрын
now this is a birthday present
@splash59745 жыл бұрын
Still following along! Love the vids. Keep em coming
@RickSolid15 жыл бұрын
My terror has been replaced by excitement now that you’re over the mid point hump...ok to be honest I’m still terrified but I’m ALSO excited now
@gunshipproduct22 жыл бұрын
To anyone watching this, please be very cautious when installing the low-reverse piston and air-checking it. You cannot air-check the low-reverse piston without the steels, clutches and center support. If they are not installed during the air-check, you can tear the seals and cause very small leaks around the perimeter of the piston. This is best seen with ATF around the edge, and applying air pressure.
@Patty__0075 жыл бұрын
Loving the series
@marrowbone71325 жыл бұрын
Good video and great camera work as always
@RonaldFinger5 жыл бұрын
So far in the series, everything has seemed to be okay. What was the culprit of the issues? Or will we have to find that out in one of the next videos?
@FuzzyDiceProjects5 жыл бұрын
Problem wasn't with the transmission, but the transfer case (which we will rebuild after the trans is back together). Rebuilt the transmission since it was out and had the parts anyway and it would make a good video series.
@RonaldFinger5 жыл бұрын
Oh shoot, you totally mentioned that in episode 2. I completely forgot! But yeah, this has been a great series so far. I don’t ever imagine myself ever rebuilding any automatic transmission, but these videos have been fantastic.
@FuzzyDiceProjects5 жыл бұрын
Glad you have enjoyed the series so far! Understandable to forget something that was only briefly mentioned in a video that came out a month ago!
@powerlightsproducoesevento7052 Жыл бұрын
Eu fis muitas aulas com eles não falo inglês mais já montei 1 câmbio 4l60e tomando aulas com eles e aprendi muito sobre câmbio
@Dvalle534 жыл бұрын
Amazing video !!! Thank you !
@rusyaidijefri42635 жыл бұрын
Cant wait for it!!! A 2 weeks new suscriber 👍🏻
@jeffr05 жыл бұрын
Thank you mr wizard.
@natefennimore78085 жыл бұрын
Love your videos, keep up the great work man 💪🏻
@travislazenby67975 жыл бұрын
MST3k Tom Servo!
@FuckYouAndYourMadeUpPronouns5 жыл бұрын
Such a nice surprise.
@slowburn35135 жыл бұрын
i love your vids man im only 13 but i know i can come back to these to help me out with this stuff
@ian_lambert-knight5 жыл бұрын
slow burn351 Boy get old!
@slowburn35135 жыл бұрын
@@ian_lambert-knight i can't speed up my aging if you didn't know lmao
@ian_lambert-knight5 жыл бұрын
Don’t come at me cuz you bad at dark old!
@slowburn35135 жыл бұрын
@@ian_lambert-knight then don't come at me "cuz"
@ian_lambert-knight5 жыл бұрын
Get old kid
@MEHoward5 жыл бұрын
This is why you always need a Tech Priest to appease the machine spirit.
@SuperDriver1015 жыл бұрын
FUZZY MAN IS BACCCCCCKKKKKKKKKKKK. FIX THAT S-10 FENDER.
@kleinemin86125 жыл бұрын
Love your vids. Keep up the good work. I subscribed too. Love you
@drewdewey92025 жыл бұрын
Are those cracks of any concern? At 8:35
@FuzzyDiceProjects5 жыл бұрын
Those lines are actually raised areas, leftover imperfections from the casting process. Pretty typical to see on aluminum parts like this in areas that have not been machined, nothing to worry about!
@battyboomfatty5 жыл бұрын
I'm glad you asked that, I was also wondering.
@Tater79bj5 жыл бұрын
Very nice! I'm surprised you didn't grind the 4 grooves in the plate thats held in by the snap ring like the Transgo kit tells you to though. It's also a very common upgrade. I guess the corvette upgrade negates the need for that?
@FuzzyDiceProjects5 жыл бұрын
To be honest, I had never heard of that before! Just searched around, appears some instructions have you do it because it helps with the speed of drainback and can be important when a valvebody shift kit is installed. Will have to remember that when I end up doing a more performance oriented 4L60E build in the future, thanks for bringing it up!
@justinmccourt145 жыл бұрын
love the videos
@Thompsongs5 жыл бұрын
Toooooooooom Servo!
@VaxisD5 жыл бұрын
ive been workin on my 4l60e and when i went to power wash the case with soap and water, after a few days it began oxidizing since ove been rebuilding at my dads place, is rewashing and air drying it the best way to prevent it (cause we let it sit outside and it got rained on as well... which i didnt want)
@md4luckycharms5 жыл бұрын
inb4 transparencies rip and you have to take the entire thing apart
@FuzzyDiceProjects5 жыл бұрын
Never had that happen! The sheets are quite hardy and plenty strong for installing pistons. If the film folds it gets crease lines, but it's easy enough to just grab another piece.
@javieraviles63143 жыл бұрын
No water when it’s cleaning up .
@jeremymalmstead53365 жыл бұрын
What is all of the cracks on the inside of the case? I'd feel so paranoid to rebuild something this big so if I saw those cracks I wouldn't know what to do.
@FuzzyDiceProjects5 жыл бұрын
Those lines are actually raised areas, leftover imperfections from the casting process. Pretty typical to see on aluminum parts like this in areas that have not been machined, nothing to worry about!
@jeremymalmstead53365 жыл бұрын
Awesome. Was pretty worried. Can't wait to see more. Also I don't know if I missed it but will you be rebuilding the transfer case since it was your issue? Would be awesome to see. Thinking of doing so in my jeep.
@FuzzyDiceProjects5 жыл бұрын
Yep! Once the transmission is back together we will cover the transfer case rebuild as well.
@nickb21795 жыл бұрын
ooc how many hours did you spend rebuilding this transmission?
@FuzzyDiceProjects5 жыл бұрын
Didn't really keep track of everything, but there was a timelapse recording running for the vast majority of the labor. Doing the math, it looks like it was running for around 32 hours, so that should be close to correct. Of course, the time would at least be cut in half if not for filming the entire process.
@ryguy23785 жыл бұрын
Can you rebuild a 2004-2010 Ford Explorer transmission
@ChristopherBell5 жыл бұрын
8:37 Can someone help me understand why it looks cracked to hell please?
@FuzzyDiceProjects5 жыл бұрын
Those lines are actually raised areas, leftover imperfections from the casting process. Pretty typical to see on aluminum parts like this in areas that have not been machined, nothing to worry about!
@camofpvreviews49855 жыл бұрын
What was wrong with the reverse gear tho?
@FuzzyDiceProjects5 жыл бұрын
Problem wasn't with the transmission, but the transfer case (which we will rebuild after the trans is back together). Rebuilt the transmission since it was out and had the parts anyway and it would make a good video series.
@camofpvreviews49855 жыл бұрын
@@FuzzyDiceProjects oh, missed that. was going to say your trans sill looks quite good as it was. Have heard that the sun gear usually shears on the reverse. Thanks for the great videos. I gotta replace my tcase on a 04 silverado z74 soon.
@MojoWitwicky5 жыл бұрын
@@camofpvreviews4985 If the sun shell splines strip out or break you lose 2nd, 4th, and reverse.
@Dungfly-dc6vg5 жыл бұрын
#2
@gregpallett18395 жыл бұрын
Does your channel have a Facebook page?
@FuzzyDiceProjects5 жыл бұрын
No, not currently. Working on improving our social media presence. Currently there is only the KZfaq channel, the Patreon, and the Instagram page instagram.com/fuzzydiceprojects/ (which is still a ghost town).
@orrprosegaming78515 жыл бұрын
Damn can you rebuild my manual transmission
@FuzzyDiceProjects5 жыл бұрын
I'm a bit overloaded on projects already, unfortunately!
@orrprosegaming78515 жыл бұрын
@@FuzzyDiceProjects ik you are besides i dont have replacement parts its a old ford trans not sure if its a e300 or a 65 mustang one
@orrprosegaming78515 жыл бұрын
Also i want to see more of that Pontiac firebird
@iansyme35355 жыл бұрын
Just my tuppenceworth…….. but would it not have made sense when installing bearings during this entire rebuild to stick them in a freezer first and perhaps also have done a bit of localised heating of the housings with a high powered heat gun of the type you use to burn off gloss paint on woodwork. Maybe less bashing and banging would then be the outcome. We Scotsmen are a lazy bunch of engineers you see!
@FuzzyDiceProjects5 жыл бұрын
You are right and freezing would probably be worth a try! Have done that for other press fit parts but never really tried it for bushings like these. Heating the case/other parts should help as well!
@iansyme35355 жыл бұрын
Keep up the good work young man.... I, and many others like the way you do these videos. If you have a spare couple of hours and want to see how to tackle an insanely difficult project then have a look at "Project Blinky" which is a major modification and upgrade of a very old mini to 4 wheel drive Toyota engine beast. All 20 episodes!
@FuzzyDiceProjects5 жыл бұрын
@@iansyme3535 We have actually been following Project Binky for a while now! Those guys are absolutely out of their minds, they are truly building an entire car from scraps and a whole lot of sheet metal. Fantastic series!
@paulboujabbour20155 жыл бұрын
Want to hear a joke? INCH
@thomaslknes49065 жыл бұрын
Automatic transmission...comlicated to understand...