Best comment goes to the guy who said.. bring back the solid barrels... all twist rates.. for slugs and pellets... no need for getting ripped off by fx for bullshit tension system.. solid we must demand fx lift thier quality

I just saw this video for the first time and i just wanna say thank u for taking the time out to make for us airgunners that are new to this sport.

All well and good but WHY? If a barrel tensioner is needed surely it should be fitted at the factory or the design should be changed so that a tensioner isn't required?

Ernest always in good form! 💪🏻👌🏻

Can't wait until it comes available to the masses. Will go real nice with the tungsten hammer. And a sexy Vox 600

I’ve preordered one, I’m glad to see that it takes the movement out of the barrel, hopefully it will solve POI shifts🤞🏼

Nice master Ernest. Proud to be Pinoy.I Don't have any fx airgun but I'm a huge Fan of this Air Rifles. God Bless and stay safe always....#Huntsman Ph.

Awesome Ernest thank you 😊

VERY exciting 😎

Awesome 👍

Ernest, thanks for the guide. Once the barrel tensioner is installed, the integrated barrel tuner no longer fits. How does one separate the integrated tube from the tuner?

Are you planning to do an install video on the upgraded power block? I have a tensioner and power block on order.

nice product. will there be tensioners for other barrel lengths?

When you have the tesioner, is there still a need for a barrel tuner?

FXUSA does this make the report louder since its not using the shroud anymore?

testado e aprovado 👍 amigo

Este é 🐯 um fã do 🇧🇷 que deseja muito sucesso cada vez sonho mais em uma like garantido sempre sempre ligado nó canal

Awesome

Thanks for for video Earnest, A question if I may, would there be any benefit of installing a barrel liner, and a barrel tensioner kit to my FX Impact M3 Sniper

Could you tell me the correct torque of the barrel tensioner end? Thank you very much, goog job and congratulations. Regards

I have had a 700mm barrel tensioning kit on order since July and STILL haven't received it yet!!!

Whats the difference between using this barrel and using Blackarts barrel band to stiffen barrel?

Trouble with the tensioner. to fix the carbon tube of the kit you have to screw the bolt at the end of the barrel on the screw that holds the liner. But these screws that hold the liner and the carbon tube are tight, the slugs go all over the place, there is no more precision. Ernest Rowe shows us how to tighten the tensioner kit but tightening the kit tightens the liner screw and we lose precision. It would take a stop for the screw that holds the liner. Do you have a solution ?

What is the size of the carbon fiber tube please. I bought a tensioned kit and it doesn’t look like the same size. Any help would be greatly appreciated.

Hello is there a version of this for the maverick? if so could you let me know thank you.

Sr Ernest estou com uma dúvida ? As fx M3 que vem com o número série acima 2153574 elas já vem com todas modificações igual o Power blok

Ernest, can you show us how to install a slug power kit in a crown?

Will there be one for the wildcat 700mm

Will the shroud from bullet central fit over the carbon fiber tension kit in 800mm I need a freaking shroud Ernest plz let me it's to loud with the shroud

Do you have 800mm barrel kits for 35 cal?

Tengo una fx crown 5.5 con barrel de 380 mm y quiero cambiar a uno de 600 mm eso va variar mucho en la precisión??

Top!

Can you install the tensioner on a fx maverick?

nice will that tensioner work with the barrel holder made by Bader Falah from saudi arabia?

Nice barrel for acuration..recomended👍👍

Are you indexing liner 1st?

Olá amigo sabe me informar se os novos fx impact m3 já são fornecidos como esses tensionador?

Will it work on the maverick?

En los nuevos m3 ya traen el power block solo cambio el tungsteno hummer correct

will there be a 600mm version i hope

Señor ya está en stock ??

can you send me the link to buy it? thank you

How many inch bound you are moved the barrel tensioner ?

Olá!! Onde consigo compra esse tensor ?

Can you provide the exact Nm torqe for the barrel nut?

Will this fit .35 caliber?

Hi Ernest is this barrel tensioner also available for fx crown mk2 . If not will there something be like this coming for all fx guns . Thanks for your programs it's highly informative and learning.

I want to knownthe truth of this systems.. when you use the carbon fibres leave with the tension system... does it really improve the stiffness of the whole barrel?

It would be much better to increase the shroud diameter, then have the jam nut with an integrated air stripper so the shroud still worked as a sound moderator, for the air to disperse. Then have the male 1/2 inch UNF on the end the air stripper for an extra silencer to be added, but I guess that part will only be available next spring.... For the right price. I'll go make one, and get back to to you all.

Can you use this kit with the carbon fiber sleeve that is installed between the liner and the barrel because I have that already installed I want to know if that carbon fiber sleeve can stay in between the liner and the barrel while using the tensioner kit with the new tension nut that goes on the outside of the barrel that's being replaced?

hello sir. I want to tell you that the part that fixes the barrel, I invented it if I can say it for 5 or 6 months in saudi arabia

I have 4 Impact MK2s. But FX is going in circles at this point. I have the original 600mm solid barrels in .25 and .30. Theyre pretty accurate with pellets. The USP of the liner system was that it was flexible to increase accuracy. Now theyre trying to tighten everything down. Why dont just make the solid barrels in all calibres and all lengths?

Will this work on the Wildcat or Maverick or any other systems apart from M3?

Wow..can I put one on my maverick 25 sniper?

This should 100000% be standard on every impact … why isn’t it?

This piece is the creation of a Saudi citizen and he has the right to be honored. He mentioned that the piece was his design, so he put effort, time and money on it

Is it required for a 600 mm barrel?

With all these add ons to improve an issue, why aren't these installed on original purchase. Come on!

Great video. When will this be available?

Do you de gas the gun prior ?

👏👏👍👍👷‍♂️

A Carabina dos meus sonhos Falta Só o dinheiro que ta dificil

boss my home is in bangladesh what is boss fx impactm3 price

Didn't work for me. First of all, with tensioning up I noted that my shots were all over the place. like 100 cm groups at 100 meters. Turned out that the barrel fix just after the block wasn't properly fixed in the factory: thus pulling the barrel out of the gun by tensioning the tensioner. Fixed that, installed again, tuned the gun. Groups did not improve beyond "before-barrel-tensioner" ( even slightly worse) and the gun got a hell of a lot louder, like .22LR loud. Other people started telling me, I should check the tensioner if it was cut properly, and if not, it could warp your barrel. I just took it of. Installed original shroud, tuned again, and am back at "sub-moa-ish" groups at 100 meters. (FX IMpact M3 sniper in .25) I decided to invest in a proper Bipod (Fortmeier, which I can fully recommend!) and in time maybe a 700 cc bottle and a backbone. MOA / Submoa groups are good enough for me.. Mind you, the barrel did stiffen up significantly. I shoot 25.49 grain pellets at 275m/s with great results. If one shoots slugs at way higher energy and speed, the tensioner might be more beneficial. I simply don't know. Just my two cents.

Is There A Tensioner For FX Crown.

Isent this more barrel pipe tensioner than barrel tensioner ? I mean the barrel are inside the pipe, held in place by the end "caps" of the barrel pipe. When i first heard of this i was thinking how the hell do they tension the barrel "straw" but i have seen they ( south African boys ) put a thread on the "straw" and so are able to pull on that just fine. I really really want to see before and after tests with this though, not that i think it will be going on my Maverick i have already poured too many money into. What i would like to see is FX putting a thread on the end of the barrel, and then just put a rifling on the remaining CM of the barrel, sort of the old ST barrel in reverse. This way we could screw the barrel in place real good, and we could pull in it real good too, and i dont think it matter if the barrel is smoother bore for the first inch or so ??? O and why do all airguns have a transfer port ( single or double ) why not have a channel on the outside between two O-rings, and then a lot of smaller holes in that channel all the way around the barrel, so it would be say a 12 port barrel. Or maybe it is a must that the air go strait into the barrel and not in a channel on the outside if the barrel and then via that into many smaller transfer ports.

在我们这只能看看的份呀

Its only a spacer away.

The way you handle rifle and scratching parts I would never send you a gun for service

if you go through my channel you can see that I explained this a long time ago, very good idea, but I'm still ahead of fx at long distance, I made a rifle and with my 406mm TJ barrel I make better precision shots you can see it on my channel airgunLR

Must be very noisy Is the bad part

Damn lots of work to do this. Why not buying a rifle with tensioned barrel instead of this mickey mouse crap.

FX should supply every Maverick owner with one of these free of charge. No way in the world should we have too pay just to get the rifle to shoot, no wonder there are so many videos on modifications and repairs. The FX brand is garbage .

What a poor design. We loose the volume of the over the barrel part which makes the gun bark more loudly. Secondly, it is virtually impossible to remove the barrel and install it again with no POI shift like it was before that tensioning system. C'mon guys, you can do better than that. If not then you can hire me but I am not sure if you have enough money to do it.

I just want to say that I find this absolutely ridiculous. A $2k+ airgun should not need to have a barrel tensioner added. If it needs one, then it should come from the factory with one that is included in the price.

Buyer beware! I have never been treated as badly as I have been jerked around by the dealer and FX airguns themselves. After spending nearly $1500 on their Dreamline classic. If they tell you they offer kits for modularity of their rifles, do not believe it. I have tried for over a year to find their supposed modular kits for their Dreamline series and have gotten put off, stalled and played email tag with these people for over a year and cannot get a straight answer out of anyone. Its more than apparent to me that it has been a complete scam. What business refuses to tell you what products they have to sell and the prices of those products? Its insane trying to get any assistance from FX. Buyer beware!

hello sir. I want to tell you that the part that fixes the barrel, I invented it if I can say it for 5 months, and if you want to see the photo is my watsapp