FY6800 Function Generator Tricks & Tips

Рет қаралды 5,569

3 жыл бұрын

should work on FY6900 and 6700 aswell
basically more than double your frequency range by using arbitary waveforms
also a neat trick to create a sweep with a trigger signal at the beginning which the normal sweep function doesnt support.

Пікірлер: 20

@richardmiranda5357 Жыл бұрын

The trigger or reference signal in a sweep generator is crucial. Another good sweep option I found for the FY6900 is by using the VCO feature triggered by a RAMP generated by channel 2. Feed the rear VCO input with channel 2 output with a 5 vpp RAMP with aprox 2.5 - 2.6 v offset, and the desired sweep time/freq. select a VCO start and end frequencies. A perfect sweep function with a reference ramp can be used with X-Y oscilloscope mode. An external marker adder can be very helpful if one or two markers wants to be used.

@richardhines Жыл бұрын

Glad you mentioned the VCO method. It works just as well as the MOD feature. Couldn't find a way to get the SWEEP feature to have a steady display on an O-scope for radio alignments.

@reaffirmation 3 жыл бұрын

Thanks for the tips. In sweep mode you can hook up ch2 of the gen to the ext trigger input of the scope and that will leave you with ch2 of the scope free.

@gamerpaddy 3 жыл бұрын

if you scope has a trigger input, my siglent sds1104x-e doesnt have one, i gotta use one of the channels for that.

@JAKOB1977 2 жыл бұрын

Interesting..pls more of such videos where you showing usecases and tips.

@cschang3282 2 жыл бұрын

thanks for showing tips of trigger for sweep , having a 6900 for years, unable to sweep with trigger signal, now I can follow in low frequency, but howto do it with sweep with 10.7Mc centered, for FM IF alignment, thanks

@gamerpaddy 2 жыл бұрын

should work the same. you set your frequency of ch1 to 10.7mhz and modulation bias to whatever your range should be you wanna sweep trough. ch2 just controls how fast you sweep but at those speeds it becomes less precise.

@cschang3282 2 жыл бұрын

@@gamerpaddy Yes, finally , I can have proper trigger for the 10.7Mc sweep centered at 5.35Mc, but if the target sweep is centered at 10.7Mc with +_1Mc width? I am using feeltech6900 20Mc unit, super thanks!

@Dezmond2inbox 2 жыл бұрын

Please check time in sweep mode, my FY6900 have issue with time...set 0.1sec...have 0.08sec approximately

@archimecatronicos5771 2 жыл бұрын

Hello, I have a question, what is the TTL-in pin in the port on the back of the function generator for? and investigated but could not find an application, I thought it was related to the function of the EXT-in frequency meter of the generator but they are not even bridged and as much as I investigate the TTL protocol I cannot find anything about that pin. Greetings from Chile.

@gamerpaddy 2 жыл бұрын

TTL in? Theres only TTL Out ABCD and RX TX GND 5v for Serial communication A is ch1 frequency Out in TTL (on/off) B is same but 180° out of phase C and D is same for ch2 The bnc (sync) are for Daisy chaining multiple devices to sync clocks. So phases dont drift apart Vco in is for vco function Trig FSK ASK PSK is for modulation function

@archimecatronicos5771 2 жыл бұрын

@@gamerpaddy Oh It's ok sorry, emm my signal generator's model is the JDS6600 and the TTL Output distribution is so different. But thanks. :)