found your content while researching a CNC g0704 conversion, now i have a pretty strong desire to CNC my 0602 when i'm done! awesome content as always, Rus. thanks for posting it!

Awesome work Rus! Should have my cnc g0704 up and running this weekend. Took it apart again to do some modifications that I think you'll really like, I'll get a video of those modifications up asap.

Great info here. I have copied your design and have it close to working. For routing the wires, I removed the upper pulley that is not being used anymore and there is a nice slot in the back plate to run the wires through.

Nice work Rus... ! Always a lot of work goes into parts like this...

Very cool! Loved seeing the indexing wheel being cut. :)

What a project! Fantastic work Russ. I'll be a regular watcher from here on in!

I followed your link for the pulse cards and what they are selling now do NOT have a socketed IC on them but it's obvious from you video the ones you purchased a few years back do have a socketed IC. I'm assuming the IC is for de-bouncing the waveform.

Great job on the Bracket and Disc, Rus Looks like it does a really good job cutting the threads. Be Safe, Sam

Great work as per usual Rus. Love ya work mate. Aaron

Not a critique, just an observation. You don't need to jaw hold it. Just get two of those wrenches (or make them, i made two for the reason you'll read) put them opposing to each other on the two nuts and giv'em a squeeze. The nut will loosen up just dandy. I made my own. One is a half moon that goes around the inner nut, the other is a full one that slides over. YMMW since my nuts are bigger (pun not intended) so i can really grip them, the keys being 2cm on the inner one and 1.8 on the outer one, no idea why the difference. Other way i've seen this done, if you don't have two keys is with a dog in the jaws, it's an axial load so no problem there either. The reason i shy away from gripping the jaws is because i keep my lathe clean. That way, if i mess up, i'll see the marks and know to never do that mistake again.

Hi, in Mach3 you can use multipulse,using pulley setup with correct ratio ex. 16 pulse 16:1 mach3 read 16 per revolution

no wonder it took you a while to get it setup, you spent some time on that bracket and it is sweet!

Best regard. Looking at your excellent video, is it not possible to implement both sensors with mach3 or the wheel with multiple slots? Thanks for your attention and reasoned response. Blessings in these difficult times.

russtuff nice work.

you made a complicate lathe . for me -the manual command remaining more easy . something to do with electronics sensors -safety stop in approach area -something to stop the machine if you try to touch accidental the rotate piece.

Hi Russ, I wonder if you could do a video on how the 2 boards where hooked up so they both work in unison. I'm confused as how this is done. I would like to do this to my mill running mach3. Thank you

hi russ, nice video, please can you start the linuxcnc guild as i am sure we are all waiting for it, thanks daniel

Good job Rus 1. are you using an lpt port bob on your lathe? 2. what is the max pulse rate an lpt port can take? thanks

Could you please to do a video explain especific how to connect the C3 Pulse Index Card to the breakboard and setting in Mach3. i will help alot of people trying to use a servo like spindle and control it by mach3.

im wondering what the advantages are with optical sensor over hall effect .

جميل

nice project, seemed a bit chunky.. but I certainly don't have any of that equipment to make something like this! What is the music you were playing there, not listed in the comments?

With another sensor you could have added rigid tapping

Great project !!!!!! Was that designed on Fusion ?

hi. nice work on the cnc lathe.btw do you an ideea where to look for feed gear box.thanks

I like your bracket and wheel. Are you using LinuxCNC? Because indexing doesn't work in Mach3 so you must be using LinuxCNC.

Best regards: Can you tell how you configurate mach 3 for threading?

The Linuxcnc documentation says that it expects 100 pulses per revolution for spindle speed. How did you get it to work with only 60? Did I miss something?

What breakout board are you using?

hi where do wiring the encoder ?

PC screws are #6-32. Do you even lift?