Grab some G54 merch here - www.en.garage5... Well, by the end of this episode you'll see that it's actually not clear cut. For business inquiries: promotion@garage54.ru
Пікірлер: 756
@dakmor659 ай бұрын
I remember a technical paper released by Mahle at some point around 2001 that documented tests on this. They found a single 180 degree cut in only the top shell gave marginal benifits, but more cuts in other areas caused a loss in HP and oil film strength.
@lookingbehind63359 ай бұрын
Exactly, there’s a reason why surface parts are flat and smooth. Lake Speed Jr has a great channel about oil here on KZfaq. It explains way more than this.
@zg29649 ай бұрын
to me it seems it would cause to much shearing and create drag. you want it smooth as you can get it
@MrFantasylover19 ай бұрын
Would be nice to read that
@zg29649 ай бұрын
@@MrFantasylover1 i wish i could read too
@therealjammit9 ай бұрын
Oil is a non-Newtonian fluid. It's supposed to "shear". That's what makes it slippery and also prevents bearing surfaces from touching when moving.
@AsiAzzy6 ай бұрын
In engineering uni, the proffesor told us a folk tale about how plain oil bearings were discovered. In early times grooved bearings were thought to be good to bring more oil to journal and only grooved bearing existed. Until poor QC had let out a set of bearings without the grooves that outlasted the grooved ones. Investigating further it was discovered that the shaft would be suspended on a film of oil making some hydro-dynamic wedge of oil with some high pressure areas. Grooved ones would not let this pressure increase and would not form the hydrodynamic wedge of oil to lift the shaft.
@frogmanant5 ай бұрын
thanks for this additional info. Every groove reduces the surface area of the bearing & reduces the achieved oil pressure.
@oshitt15 ай бұрын
It does. The opposite it scrapes off the oil. It's all in the pressure of the oil, Too much pressure will slow you down.
@fia77119 ай бұрын
This is why tires have grooves in the threads. To prevent the formation of a layer of water that will cause hydroplaning. If this is applied to the journal bearing, the oil layer will disappear.
@jovanduclair54127 ай бұрын
Very good comparison
@DavidMarcy-pp6jv6 ай бұрын
That's what I thought.
@MickH606 ай бұрын
No it won't, very different scenarios...
@KenHMladin6 ай бұрын
Agreed
@supernova5end6 ай бұрын
this isn't a good comparison because the grooves in the bearing would be the road and the crankshaft would be the tires. I think to actually get this to work would be to increase oil flow to the bearing to account for the loss because of the extra area.
@neilmchardy90619 ай бұрын
When you add grooves to the bearing surface you simply give the oil somewhere to be compressed into, increasing the mechanical pressure on the bearing. Increased wear
@jamesg82466 ай бұрын
Yeah. It's clear some people don't understand that the metal surfaces aren't meant to actually run on each other... there's supposed to be a thin layer of fluid suspension via oil pressure. These holes wreck the physics behind why this works..
@garyr70276 ай бұрын
Only way around that would to have porus bearings with real tiny oil pockets. Most bushings have tiny pockets that grease sits in to give a further lifespan. Like a sponge they absorb grease to be released when in use. Of course the difference being a engine has a oil pump, but then once it's out of oil, a pump then serves no purpose without oil to circulate... Lol. The biggest problem here is the holes drilled and the groves where way oversized, plus they used the same engine with all those metal particles they never flushed out.
@jamesg82466 ай бұрын
@garyr7027 and to complicate things, the hole size needs to vary based on viscosity of the oil at the entire operating range, because the hole size needed for 5W-30 @ 50 degrees F is different than the hole size needed for 0W-20 @ 100 degrees f
@VeritasEtAequitas5 ай бұрын
Yeah, this is absolutely ridiculous. They would need super high precision machining and polishing to make grooves without raised edges that will destroy the entire bearing system regardless of the grooves. I can tell you exactly how this is going to fail without even watching the full video first....
@tomasnokechtesledger17865 ай бұрын
Nope, you were wrong. The engrooved bearings endured flawlessly.
@SSChambers19 ай бұрын
To Anyone familiar with the ol' 4G63 in the 2nd generation Eclipse (7-bolt): They were notorious for crankwalk (premature thrust bearing failure). I had 2 engines walk on me. I got with a machinist when I rebuilt my '97 GST and we decided to chamfer the thrust bearing in an attempt to assist/direct oil flow to the thrust face. After getting my main bearings back, I rebuilt the engine and made sure to properly seat the thrust bearing. Crank end play was within spec (0.005). I put nearly 75k on that engine until I finally sold the car. A few months prior to selling it, the crank end play was still within spec. I made a writeup on DSMTuners many years ago regarding my "fix". Got a lot of hate but also a lot of praise. I think 75k on a rebuilt engine (and was still going strong) speaks for itself. Cutting channels or chamfering bearings isn't anything new but the engine still requires oil to run. Kind of defeats the entire purpose of this test.
@chiefdenis9 ай бұрын
Removing the oil was a quicker way to simulate worst case scenario
@ElectricSwordfish9 ай бұрын
I found your article just by searching "chamfer thrust bearing DSMtuners" in the Google search bar...way back in 2009! Super interesting read and find, and for some reason Ive always enjoyed reading forum posts from a long time ago.
@Marc83Aus9 ай бұрын
How much was the chamfer?
@nastybastardatlive9 ай бұрын
My 4.6 Lincoln has 460,000 miles. Stock bearings. Never rebuilt. Second guessing billions of dollars of factory R&D and a century or more of experience and history is a fools game. Some garage mechanic kid watching tic toc videos then giving out advice on engineering is ludicrous. Do you even hear yourself?
@dan79transam658 ай бұрын
I'm guessing you have the split bearing. I'm rebuilding my 6 bolt right now
@hitekredneck1099 ай бұрын
This was a great demonstration of how surface area works! Slotted bearings "might" be of benefit in certain applications where a very high oil volume can be used but slotted bearings are prolly best left to where they've always been used......in applications where they are greased.
@TsunauticusIV7 ай бұрын
I agree. I think the better test for this would have been a miniature version of machine way scraping. The tiny gouges provide pockets for oil to sit. It works beautifully on machine ways. Wonder if it would work, on a smaller scale, on bearings in engines. 🤔
@feluke83964 ай бұрын
@@TsunauticusIV They won't work because bearings in engine work on hydrodynamic oil wedge. Groves are good for applications, where you can't get oil wedge to work (low speed, change of direction) and in low load places.
@FuckGoogle5029 ай бұрын
It's for extra oil capacity so that the engine can handle higher bearing loads (i.e. higher cylinder pressure) without squeezing out the oil film. It's an old drag race trick. It does work, but that seems like a bit much volume. Also, you want the groove to allow the oil to flow without turbulence from the feed hole. Race bearings usually come with an oil reservoir groove from the factory and you can choose whether you want it to go all the way around or just through one of the shells.
@pcshooter9559 ай бұрын
i built a racing engine for my bike which revd to 20k rpm it had that oil grove in some bearings but not all i guess they know what ones need extra oil i think it has something to do with crank flex \
@NVMDSTEvil9 ай бұрын
@@pcshooter955 I think shaping the cuts similar to a tractor tire tread in the direction of rotation to funnel the oil towards the center of the shell would provide the most improvement vs an X-style. Actually it would be interesting to set up a bearing wear tester like what Project Farm has and test some different cut styles to see what cut can take the most pressure before wear occurs.
@Eluderatnight9 ай бұрын
I see it in low rpm industrial applications where exposed to dirt and metal shavings. The junk goes into the grooves and protects the majortity of the bearing surface.
@johnhickman1069 ай бұрын
It’s all pointless if there is no oil in the pan. This only proved that no oil will cause an engine to seize, which we knew it would.
@Eluderatnight9 ай бұрын
@@johnhickman106 look up hydrodynamic bearings. It will run until all the oil is squirted out.
@jsheradin9 ай бұрын
Testing these without oil probably missed the point of this mod. By adding the scores you create an oil galley which might supply oil to an area of the bearing that would otherwise be starved at high RPM, etc. Plenty of engine designs already incorporate these groves from factory but I don't know of any that use a cross-hatch pattern like that.
@SparxI09 ай бұрын
It would be hard for them to test longevity of the mod with oil in the engine because presumably the engine will last another 100,000km at least, which would be a lot of testing Maybe Project Farm should tackle this one. Run each engine for a full 10,000km oil change cycle and send in both oils for analysis
@twatdidusay3049 ай бұрын
@@SparxI0I like the way you think. I was thinking the pretty much the same thing. Project farm needs to test this like you're talking about.👍
@JT_7719 ай бұрын
Not that this has any real chance of anything approaching useful.
@matthewmorgan5829 ай бұрын
I don't think it actually improves anything regardless. The crankshaft doesn't physically ride on the bearing, oil pressure keeps it suspended. In order to have better oil film strength you'd need a higher volume oil pump or a higher weight oil. That's why high-rpm race engines use oils like 0w50.
@ravenrock5418 ай бұрын
#1 Those divots will collect grit in the oil. #2 The divots would create turbulence in the oil film (pressurized oil layer) Turbulence would create high and low pressure areas.
@ashiehakoto14909 ай бұрын
so this is supposed to allow better lubrication by carving channels in the bearings. but I see a few problems with the idea.
@snipersquad1009 ай бұрын
By not having oil in the engine defeats the point of this whole exercise.
@forbiddenera9 ай бұрын
@@snipersquad100exactly what I was thinking 🤔 wtf I can't believe they didn't realize that
@jeremypike91539 ай бұрын
I don't think bearings work the way that whoever suggested this idea thinks they do. In a running engine oil suspends the crankshaft journals in oil. Only on start up are they theoretically not being held into suspension. Any bearing is going to fail if no oil pressure is present. I would imagine if you cut into them they would probably fail even quicker.
@Dongskie29 ай бұрын
It will loose oil pressure
@matthewmorgan5829 ай бұрын
@@jeremypike9153 Exactly. More surface area means less pressure suspending the crankshaft. If you really want higher bearing film strength just use a higher weight oil.
@randomoinkbomb9 ай бұрын
If the carvings were meant to improve lubrication to the bearings, why was the oil taken out? Kinda counterintuitive
@breakz1879 ай бұрын
yup. silly video this one
@olavl88279 ай бұрын
Yes, well. I enjoy this channel for the crazy experiments, but these guys are obviously not engineers. There's often not a lot of reasoning to what they do. They just do whatever.
@breakz1879 ай бұрын
@@olavl8827 I know I know. I knew someone would complain. I love this channel, but pulling the oil makes no sense when adjusting the oil passages.
@pcshooter9559 ай бұрын
its a fail rate control test if you know what your looking at,..
@antonisantonis6559 ай бұрын
yes, i was thinking the same maybe they are thinking that the grooves they made will keep inside them more oil than the normal bearing and the engine will last a bit more before sizing
@Star_of_the_new_moonАй бұрын
One of the best if not the best most practical real world mechanics channel on KZfaq
@aaronlayes44856 ай бұрын
Thanks for doing these shows. It has been nice to see a show that replicates the old car shows of the US from back in the day. Many of those shows no longer exist and it was a huge part of my childhood. I grew up around cars, my dad use to be in the car builder groups. when I was 7 I met Carol Shelby, and got to know and like the guy. Later I would meet other big names including Jay Leno by just hanging around the car shows with my dad. this show not only reminds me of the few good times in my life but also makes me smile, and sometimes laugh like I find so hard to do anymore. thank you again for providing something that helps me forget the insanity of the world for a little while. seeing what's going on in my country breaks my heart. Your content lets me think of better things. Thank you again for all that you do, and may you have great success in anything you do.
@AC-io8qs9 ай бұрын
That's a lot of work just to prove what anyone who has ever worked on engines would know without asking; thanks for your hard work and hopefully it helps someone from doing something stupid!
@RiceCakeWtf9 ай бұрын
This, but I assume like most mechanics looking in the comments here, we're just looking for the 16 year old to laugh at who promises he's been building engines like this for 40 years and they just did this 'wrong' because it 'totally works'.
@AndyKPOV9 ай бұрын
I can change the bearings in my truck in about a hour. In most cars I can in about an hour. No one said anything about a rebuild... I can pull a oil pan and baffle pretty quick. I would not recommend it but it's possible.
@jakepalmer19869 ай бұрын
*Video Idea* Can you save a seizing engine, run an engine with no oil to the point where it begins to struggle, then poor oil into the running engine to see if it begins to run easier again.
@amdintelxsniperx9 ай бұрын
someone did this they used a cut off knob to stop oil flow then turned it back on . the engine still stalled since the oil takes a bit of time to get to all the moving components
@zcomputerwiz9 ай бұрын
I would expect by then it would be too late. It starts to struggle because of bearing material galling, adding oil at that point probably won't help much since it is already metal on metal contact.
@Mastermindyoung149 ай бұрын
It'll run easier with oil than it did without oil, but bearings can't become un-toast.
@jake_break91859 ай бұрын
@@Mastermindyoung14well said lol
@khrisshultz25327 ай бұрын
It'll probably hydolock
@MrWorth669 ай бұрын
i think whoever thought groves would work in a Babbitt dosnt understand how Babbitts work.
@ryurc30335 ай бұрын
It's funny they think It just splashes around willy nilly.
@grantreid85836 ай бұрын
There was a modification we used to do on our local 6cyls here in Australia for performance applications. We used to machine a groove right around the crank journals lining up with the oil hole it seemed to work but the engines were fully rebuilt with rods resized and crankpins ground so that the bearing clearances were close to minimum size which gives you much better oil pressure as the oil loss is minimised with the tighter clearances.
@SeymourBalz9 ай бұрын
Your better off to chamfer the oiling holes in the crank. In the fashion suggested your just adding areas for debris to accumulate.
@MeriBadger9 ай бұрын
THISSSS
@thatguyalex28359 ай бұрын
I know nothing about bearings, but chamfer/smooth edges around the oiling holes makes sense, to reduce places for debris to get stuck to harsh corners. Also, humanity is better off by not taking Tic Tac advice. ;)
@SeymourBalz9 ай бұрын
@@thatguyalex2835 I put a couple engines together... It works. BTW, that oil hole is sending pressurized oil to the inserts. (Bearings)
@PenkillerDIY8 ай бұрын
Guys, 1HD-FTE has its main bearings honed as installed in the block tunnel. - for oil retention purposes, it's also able to operate at 0.25bar at idle. - according to the book, good SAE-30 returns 1.3-1.5bar idle pressure.
@craigcampbell85609 ай бұрын
Drilling and slotting engine bearings will make NO difference at BEST. Whomever came up with this idea clearly does not understand how engine bearings work in the first place. Under normal operation the bearings and crankshaft journals NEVER actually touch each other, they are separated by a layer of oil that occupies the clearance space between them. This is why engines can easily last over 300K miles when maintained properly. There's NO metal to metal contact in the bottom end, there's only metal to oil contact under normal operating conditions. That's why changing your oil and filter is so important. Drilling and slotting the bearings removes material which increases the amount of oil needed to fill the space, which is not ideal. It also gives more routes for the oil to go between the bearings and the rods/mains and caps. While it may not cause any harm at all, it sure as hell isn't going to make the engine more reliable since it's inviting a condition that's less than ideal. I'm guessing the idiot who came up with this was thinking that drilled and slotted bearings would be better since drilled and slotted rotors are better. The problem is with brakes you're trying to create friction to stop the car, and there's no lubricating fluid present to lubricate and remove heat for a reason. The holes and slots allow some air to come in and cool the rotors and pads to prevent brake fade. With engine bearings, you're trying to prevent friction. You're also removing heat buildup with oil. Unlike brakes, you are trying to keep parts from touching, so there's already a void for the coolant (air for brakes, oil for bearings) so creating additional space for the coolant to flow is completely unnecessary. That's why there's basically no potential for gain. Kudos for Garage 54 for conducting the test even though they surely knew that the bearing modification had ZERO potential benefits. It's a stupid idea.
@lelandlewis72074 ай бұрын
There were two things overlooked in this test, bearing clearance and the distortion of #4 rod after the first test. The rod would be out of round after knocking for all the time which would affect clearances and change the parameters of the second test. Since clearances weren't checked before each run, the mains may have had different clearances, affecting how they performed, not to mention any debris left in the engine from the first test would go through the mains first. Still, it was interesting. I can see the modification allowing more oil to be held in the rod bearings and possibly giving a bit more shock-absorbing capacity, but, once oil flow has stopped, the flat surfaces will lose their oil just as quickly as without the grooves. In racing, we modify the whole oil system to give as consistent a flow as possible. There was a time when we used "full groove" bearings to supply oil to the rods at all times, but it was found that the loss of bearing area wasn't worth the oil supply, so it was dropped back to "3/4 groove" and in most cases, we just use the "1/2 groove" with modifications to the crank and block to improve oiling and the oil pump for higher pressure and in some cases, higher volume and pressure. In most cases, these TikTok and KZfaq modifications are based on opinion of what seems to work, not on actual testing and experience and in some cases are outright wrong. I have seen many that are old hotrodder thinking from 80 years ago that young guys are just hearing about and has been proven not to work as well as thought, but people go by "seat of the pants" feel and think it works. Many of those modifications either don't do anything or can destroy your engine if you don't have the exact engine they are tried on. For example, I saw a timing trick that is almost as old as racing itself, and if you have a low-compression engine you can "get away" with it, but if you try it on an engine with 9.5:1 or higher, you have a good chance of causing detonation. Unlike the old saying, what's good for the goose, isn't always good for the gander.
@cobrasvt3478 ай бұрын
The very reason you always chanfer the oiling ports and micro polish out any imperfections between the bottom of the chanfeer and the bearing surface. Without doing so would induce scratches in the thin layer of babbitt on brand new bearings causing severe premature wear. I would recommend a muriatic acid bath for each of the crank journals to remove any foreign material embedded into the casting from machining, poloshing or prior bearing failure if damage to the surface isn't significant. This works for small single cylinder engines that have had rod failures and have microscopic embedded aluminum particles in the connecting rod journal. The acid will boil out the foreign aluminum material and leave the cast steel crank journal unharmed.
@poptartmcjelly70549 ай бұрын
Scoring the bearing will only decrease the load bearing capacity of the bearing. In the old days both the top and the bottom bearing shells had an oil groove, but Chevrolet found out in testing that the groove instead of helping lubrication just broke the fluid film and reduced the load bearing capability of the bearing my 2.6 times. This is why modern engines do not have an oil groove in the bottom bearing shell. Scoring the bearing only lowers the load capacity and if the fluid film fails then the crank will block the extra oil channels and starve the surface of oil.
@dimitar4y9 ай бұрын
my man! Yes! You know about fluid film! Like precision swiss lathes. Many idiots just "oil good, more oil in oil good, ooga me smart" and they are so confident, SO confident... dear lord.
@kikihun97269 ай бұрын
I would have added oil to the tests and measure the temparature on the pan bleed hole to a bucket and pumped back to the oil intake. Or something like that. With this you could have measured the temp difference of the bearing.
@madjimms9 ай бұрын
I really hope you smoothed down the cuts after, otherwise there will be burs
@brentmiller39519 ай бұрын
Na these guys are amatures they could not figure that out
@fastinradfordable9 ай бұрын
@@brentmiller3951they are more capable than 99.8% of professionals in North America.
@TurboVisBits9 ай бұрын
i believe that was sarcasm. @@fastinradfordable
@Lofi.z349 ай бұрын
@@fastinradfordable The US has some of the world's best engine builders. But you're probably just jealous. From Chris Forsberg's Alpha VQ to Texas Speed's LS engines... there are shops that make 3000 hp Viper V10's that will make any european V10 piss itself. So yea you're way wrong
@qwulong30049 ай бұрын
these tik tok hacks are hilarious more in the future please and thanks bmi Russian
@jamesdexter7481Ай бұрын
To use the car tyre analogy, if you drive on a wet road with tyres with little tread left the water will cause your tyres to aquaplane meaning there is a layer of water between your tyres and the road causing low friction, whereas having plenty of tread on your tyres allows the water to escape so the tyre can make contact with the road causing high friction. Always have at least 3mm of tread on your tyres folke and NEVER believe what you see on tic to.
@chrishartley12108 ай бұрын
You need enough bearing material to support the load being applied. Simply cutting grooves into the bearing reduces the material. If you want to increase the load you need more material, in other words a larger diameter or a wider bearing. If you use a wider bearing the edges of the bearing may not receive enough oil which is where the grooves come in, but they have to be carefully designed rather than just adding random grooves.
@GHOOGLEMALE9 ай бұрын
Low oil pressure surely?
@CameronM479 ай бұрын
I'mma go out on a limb here, and guess the lack of oil caused it to seize.
@lookingbehind63359 ай бұрын
Exactly how would you demonstrate the failure with an oil supply? The video would be years long.
@scottgarmon48658 күн бұрын
Funny story..when I was a kid I put a used engine in a 89 Honda civic at my dads shop on a Friday. after finishing up I wanted it to sit and run inside the shop bay , I got busy as It was time to close so we shut the doors and closed for the day. We come that next Monday and the Civic is still running. It was so quiet that nobody noticed it and I had forgotten that I left it running. My Dad was not impressed with its amazing fuel efficiency. lol
@user-ll1cd1lh9y7 ай бұрын
It really works,the trick is oil pressure relies on clearances, when you do the modifications oil pressure MUST be increased,our engines Bbc,was increased to over 100 lbs.for this to work,it was worth .6 in 1330 and 77 HP,was able to run mains all year,rods x 3 and we are looking at cam bearings,not advised (most critical pressure bearings),
@wwmoggy9 ай бұрын
how about fisrt get rid of any Burrs then have 2 matching cars leave oil in drive 5.000 or more miles then compare the resaults.
@SparxI09 ай бұрын
Yeah they should send in the oil to a lab for analysis
@wwmoggy9 ай бұрын
removing the oil defeats the reasoning for the grooves in the first place
@jonathanbrown11209 ай бұрын
I’ve seen bearings from factory with a single diagonal slash but not that many of them.
@dimitar4y9 ай бұрын
a single slash helps clean the oil- shaves it off and forces it to come out and be refreshed with new oil. minor benefit in specific applications. Otherwise crud could just do the full spin cycle forever.
@theepicslayer7sss1019 ай бұрын
wait did i misunderstand, you guys tested oil channels without oil? if so, would like to see how well it helps with oil... if not then i guess there was not much difference with how the oil behaved.
@HungryTv139 ай бұрын
They just tested it more quickly. A real test would take long time. But this just quickly shows that the grooves dont really lube up the bearing better. The geoves should of allowed some oil to stay inside the bearing a bit more but wasnt the case. As they survived the same, even less time as the rpm was a bit less. Even if they drop oil, the engine will still have some oil and parts will still e lubed up contain a bit of oil. So it was a super quick test to see if the modifications any useful or not.
@theepicslayer7sss1019 ай бұрын
@@HungryTv13 ah so the engine had oil in, sounded at the end like it was run dry yet i kept seeing the oil pan with oil and a lot of metal shavings thus why i was asking if i misunderstood it!
@Floofie_boi9 ай бұрын
If this really helped get engine performance and better lubrication, I'm sure car manufacturers would probably be doing it
@jttech449 ай бұрын
Many manufacturers use grooved top bearings, but it's a single groove, and mostly serves to supply some extra oil to the cap side of the bearing. It's also not 180 degrees to force the oil to spread by the time it gets to where the bearings meet.
@restojon19 ай бұрын
I liked the bit when they carefully measured the oil clearances in all the mains and big end bearings and checked the thrust loadings.
@pohldriver9 ай бұрын
The bearings are there to protect the crank journals. The pressurized oil prevents metal to metal contact. With enough contact, the metal heats and acts like a brake, causing a seize or spun bearing. Dirty oil contains soot, metal particles, and acid that are abrasive, causing wear. As they wear, you lose oil pressure, leading to failure. A proper test would have been to bolt the engine to a large water pump with a valve to restrict outlet flow. Then restrict flow until full throttle maintains 3000 rpm. Then, under full load, let it run for 7 days or until failure. The disassemble the engine and assess the bearing condition.
@ukkomies1009 ай бұрын
What do you mean water pump. Like bolted to the cooling system
@pohldriver9 ай бұрын
@@ukkomies100 no, like an irrigation pump.
@Kowyn9 ай бұрын
So you're supposed to improve bearing performance by reducing the bearings surface area?
@SparxI09 ай бұрын
I think the idea is to trap some oil in the grooves, but it wouldn't be a nice smooth oil film like in a normal bearing
@martin-vv9lf9 ай бұрын
@@SparxI0 I've seen these type of bearings with a parallelogram groove sold commercially, but they are for use in a gearbox for instance, where there is no oil pump to lubricate with.
@dimitar4y9 ай бұрын
yep..... spoken like someone who actually understands engineering. grooves help oil do what now? we want the oil squashed into a film, not into whatever cavitation nightmare that gallery is.
@bobirving60529 ай бұрын
Thanks for doing crazy experiment. Surprising that the modification helped rod bearings. Bearings aren’t supposed to “rub”. Not actually supposed to even touch. Supposed to ride on a film of oil only.
@platinumgrit6 ай бұрын
bearings supporting the crank are supposed to be as flat as possible. The crank is supposed to spin on an oil film, that's provided by oil pressure from the oil pump to the bearing face. Oil is supposed to be pumped from supply holes inside the crank, at pressure, to the bearing face. This 'mod' is going to destroy the whole purpose of the bearing - to provide a surface where the crank can spin on an oil film. Now the oil is going to drain away from the bearing surface, and the crank is going to touch the bearing surface, and not be suspended on an oil film. The only way this mod can work is if you dramatically increase the oil pressure and flow from the oil pump, to compensate for the extra loss of oil from the bearing surface.
@philipparge80647 күн бұрын
Reminds me of the government "cash for clunkers" program, where engines were killed on purpose! I have seen use of "spiral grooves" on huge bearings with L/D of 1 and a max RPM of 50 rpm. Grooves allow cooler operation. Also pure silver babbit metal for high temps.
@mrheart42429 ай бұрын
This should decrease oil pressure dramatically. It should hold oil for start up. But, the bearing does not ride on the crank. But on a thin layer of presurized oil between the bearing and crank. This is why the oil is filtered and changed regularly. In a hi volume oil situation, 5 to 300 gallons. The filter is changed but not the oil. It is topped off.
@donjohnston42157 ай бұрын
The whole idea of oiling the crank through the hole in the bearing is to A-create a film of oil for lube, and B-the oil being forced out across the face of the bearing is the largest way heat is removed from the crank. By cutting groves you are changing the way it’s designed to work.
@keithstevens17139 ай бұрын
The channels carved into the bearings are like tires on a wet road, they disparate the oil and reduce the wearing area
@natereinhold61809 ай бұрын
Unless you have a high volume oil pump, id think most of the volume would follow the groves and not lubricate the bearing faces. Seems youd have to have enough volume to surpass the volume the groves have to be able to force oil to the faces. Edit: after watching video, i see that its meant as a way to allow oil to get to the entire bearing after oil pressure loss. I do know that the mods will help on a greased bearing vs pressured oil lubed. Moreso to allow the grease to make it around the bearing instead of squeezing out at the grease port.
@sacr39 ай бұрын
The whole purpose of those plain bearings is to allow an extremely thin layer of oil to evenly distribute itself between the crank and the surface of the bearing, so there is never any metal to metal contact. By digging channels and having rough spots, there is less surface area for that evenly distributed layer of oil, and those channels act like scoops, potentially pulling oil from that thin layer. What about heat? I see plenty of spots for stress risers where cracks can develop. I see digests that can collect tiny bits of debris over the life of the car. Plain bearings aren't supposed to be damaged in the slightest, or else you get premature failure. I've seen plenty of vehicles hit over 400k with proper oil changes never require plain bearings to be changed, so this is just silly in itself. Never take advice from tiktok, its a platform loaded with idiots sharing idiot knowledge.
@dimitar4y9 ай бұрын
"cargo cult" and "krugerites", are the correct terms but yeah it seems most of these, "influencers" get worshipped because they are dumber than a technician, and the dumb hate feeling wrong/dumb. So they find someone to agree with them and worship it as their own gospel. And they also worship something that should be debunkable as false using just common engineering knowledge.. that they lack..
@Ecksterphono9 ай бұрын
Might want to tweak the oil pump as well. Too many modifications in the lubrication system may affect oil pressure if put in full time service with oil.
@MrFantasylover19 ай бұрын
If they took the pressure relief spring out and shimmed it to boost oil pressure I think the modified bearings would be amazing in the long run.
@holycrapski14 күн бұрын
Reminds me when I was a apprentice in the 1960s scraping white metaled shells to fit reground crankshafts, The good old days.
@Banditt429 ай бұрын
Tik Tokers would microwave their pets if there was a tik tok telling them to do it.
@dimitar4y9 ай бұрын
they already did. They ate tide pods, killed themselves, held their breath to make free underage snuff for the creeps.... Hell of a world we live in.
@TheTempest9099 ай бұрын
You should have left the oil pan off and used a thermal camera while they were running. As far as testing longevity I would put the engines in a couple cars go beat on them equally. Then send the oil out to a lab maybe?
@kris8569 ай бұрын
russians don't have such a thing as a thermal camera
@Thingsthatgopew229 ай бұрын
Then, CNC/Drill cooling fluid would be quite a good fluid inside a motor? Test it! The white stuff made of oil, water and emulsifier.
@dimitar4y9 ай бұрын
water = rust cooling fluid helps cool yes, but it doesn't lubricate. These are modern bearings that rely on a thin film of oil that acts as bearing balls. Hence why the oils have metal additives - that fine metal dust they add *is* the bearing material.
@baby-sharkgto49029 ай бұрын
If Clevite and King aren’t doing it then either am I
@alistairwhite29065 ай бұрын
Any break/edge in the bearing surface will cause an interruption to the oil film and increase wear. A slight radius on the oil feed hole is all you need. The rest of the surfaces should be completely smooth/uninterrupted.
@maikeru019 ай бұрын
putting scratches in bearings completely defeats the purpose of having bearings. the whole idea is to have as smooth a surface as possible in order to minimize friction. you can not improve on with cutouts. guaranteed you will wear out the shafts faster. The bearing got stuck on the crank shaft because the scratches gripped onto the shaft because it wasn't smooth. Don't trust any of those stupid chinese tiktok or instagram hacks. they are just making things up to get video views. they have literally zero smart innovative ideas.
@123dasilva49 ай бұрын
If they had good ideas they wouldn't be Chinese
@dimitar4y9 ай бұрын
those tiktokers, "influencers", simply spread the unspoken "cargo cult" culture that's forming. They make something that "Looks" like a "Whatever the tiktoker said it is", and then in comes worship of said "idol" .... Call it a "bearing", then call it a "improvement", and people obey mindlessly... It's just worship of gospel, when you break it down, really.
@hedaron37878 ай бұрын
The real bearing is the oil while it's running. The question is if this improves that cushion.
@dimitar4y8 ай бұрын
@@hedaron3787 na, it breaks it. It's called a "oil film" and there's a complex science behind it. Laminar flow helps it stay "strong".
@jimfarrow55268 ай бұрын
This is actually the way early engines were done like model a and model 7 also bearings were poured in place
@prano20019 ай бұрын
id like to see a similar experiment performed, start with fresh bearings such as you did here, then run it without oil until the engine starts to drop revs and knock, but pour oil in while running to see if it quiets the knock and prevents the engine from seizing or if the engine will still fail in the same manor once it can lubricate everything. providing the orifices that lube the crank and con rod journals dont plug
@Evanx3739 ай бұрын
Once it starts knocking it won't stop if you put oil in. Damage is already done
@VitoVeccia9 ай бұрын
They are called friction bearings for a reason. Cant stand it when people make stupid videos just for views. Thank you guys for putting this through a real test.
@ljubomirculibrk40979 ай бұрын
Minimum growe can improve oil film, plus catching particles that can damage surfaces. If growes are reducing oil film pressure you get increased friction instantly. Oil shud prevent contakt of surfaces totaly. Big industrial machines use hydrobearnigs, oil is pumped under presure, precise gap betven surfaces, just enough to oil seep thru the ends, constant circulation.
@bluemeanie63959 ай бұрын
a thin film of oil across the bearing prevents the surfaces from touching. The grooves would make the oil squish away easier
@mightyweapon7 ай бұрын
As a professional qualified automotive machinist of 20 years, I'm lead to think it won't increase service life, putting drill holes and extra grooves in the bottom side bearing is just breaking down and interfering with the hydrodynamic wedge, especially on the big ends, and will interfere with the oil flow and heat removal of the main bearings.
@anibalbabilonia18679 ай бұрын
👋😂👍I’m surprised it lasted this long! Next week they rebuild the engine and use it for another crazy experiment!🤣👍
@isaacwhite74119 ай бұрын
The modification may help with cold starts , cause of the pooling effect it maybe worth experimenting further.
@kinglouis69749 ай бұрын
A cold start situation is more of a top end of the engine I would of thought
@lookingbehind63359 ай бұрын
No, wouldn’t help at all.
@isaacwhite74119 ай бұрын
Well the oil will pool in the dibits at lease it would have some lube before cold dry start.
@isaacwhite74119 ай бұрын
@@kinglouis6974the top really have the high revolutions as the crank when cold starts and maybe depends how the top is designed if it has a cam it may help to.
@isaacwhite74119 ай бұрын
@@kinglouis6974it may help when theres no oil pressure when cold starting
@thatjdmkid81709 ай бұрын
To actually know if it makes a difference you will have to put decent mileage on the engine with Each bearing then measure the tolerance!
@babaoreally82209 ай бұрын
On a GOOD test mule that provides proper oiling,itwould take at least 50,000 miles on a main bearing to do a forensic wear evaluation.Unless of course there are assembly errors( both journal and side clearances)which cause catastrophic failure,or oiling issues,which is what this appears to be.Such a test can only be credibly evaluated in an engine laboratory.Also,I’m used to seeing bearings,here in the US,with a single bearing groove on mains and numerous shallow linear ridges across the surface of the rod bearings,which provide ample and even oil distribution across the entire surface.At one time TRW offered a fully grooved main bearing.I used these in on my RA/IV build in 1970.
@brandonobaza86107 күн бұрын
I turned my back on social media "life hacks" forever when I saw one about cooking hot dogs in a coffee maker carafe.
@mikel96567 ай бұрын
Mechanical Engineer here, this bearing mod would be marginally helpful; in only 2 situations that i can think of. 1st a high horse power build with a higher pressure and flow oil system i might help flow more oil to the bearings of your choice. 2 when your slapping an engine together and are unable to get the proper clearances for whatever reason on a specific bearing, specifically too tight. by cutting the channels you are increasing the flow to that specific bearing keeping it cooler and more protected compensating for the tighter OOS clearance. But with that being said i wouldn't do it for any build i was intending to run. journal bearings acutely use the pressure of the oil trying to escape to the sides of the bearing to levitate the spinning shaft on a layer of oil, the 2 sides should never touch. so in most cases this mod will only hurt performance because it will though off the delicate Ballance the engineers dessinged into the engine.
@christopherleubner66337 ай бұрын
If this is done correctly, it ensures the oil flows evenly over the shaft. I have seen extremely similar designs that used air with the bearing surface floating on a cusion of air.
@garyr70276 ай бұрын
Having a pressurized oil surface across the entire width of those bearings would be better imo, unless a oil channel is necessary to complete the oil circulation thruout the entire lubricating system. However, no mention of flushing out that engine after the first time, would end up decreasing the odds for the second go around. This should have been done on two different engines to get the proper results. The first go around left all kinds of metal particles in that motor that effected the second test.
@prestonfaceman9 ай бұрын
replace your engine oil with water, see how long and well the engine runs. I tried to kill my car like that once, drained crank case and filled it with brook water. It still lived and drove around the scrap yard for weeks. Seized up once, dumped 3 or 4 buckets of water on engine to cool it, topped up the case and it fired back up. It refused to die until we flipped it with the loader and squished it
@u.e.u.e.7 ай бұрын
So the most effective way to make this Lada engine last longer: improve the oil flow and the oil pressure to cylinder #4. 😃👍
@peterbustin26839 ай бұрын
Fascinating stuff on this channel. Thanks, guys! ❤from UK.
@Mike-xt2ot5 ай бұрын
Back in the 80s my machine shop alway cut a groove in the center of the main jourmals on AMC v8s.
@Artoconnell4 ай бұрын
Sounds like a good way to quiet down actual bearing wear without spending any money. might hold together for a week or so.
@iknowyourebrokeauto4689 ай бұрын
Would have been better flow if it had oil but better flow equals less pressure
@dimitar4y9 ай бұрын
and pressure is what we need to maintain the bearing surface nice, tight and frictionless...
@iknowyourebrokeauto4689 ай бұрын
@@dimitar4y engines will run fine with 10 psi per 1000 rpm
@dimitar4y9 ай бұрын
@@iknowyourebrokeauto468 unless you add defects that torture the oil film :D
@wendellvoisin70906 ай бұрын
The only place I have ever seen bearings being grooved anything like that was when grease was being pumped into the bearing and that was only once in very large poured in place bearings for low rpm shafts.
@malcolmmackenzie92029 ай бұрын
Woukd be cool if they re did this but had low oil pressure instead of no oil at all then there would most likely be a big difference between them
@DriftCentral9 ай бұрын
A lot has been overlooked in this conclusion
@robbdudeson3464 ай бұрын
The "Theory" that they probably thought that More Oil would flow through the Grooves theoretically increasing the ability for the Oil to spread more evenly across the surface of the bearing, ... but that's Not how MainBearings and Oil Viscosity works... The Bearings rely on the Oil Film Layer to be Stable to absorb Impact Forces and make sure the Molecular Layer of Oil is Evenly Spread throughout the Bearing Surface... with the Grooves it disrupts the Layer Stability of the film and will eventually cause Bearing Failure
@bunning635 ай бұрын
Ford had an SAE paper back in the sixties outlining the no, no of grooved lower shells in tests.
@kerrypierre94949 ай бұрын
I would say, this proves the engineers knew what they were doing.
@TowerCrisis9 ай бұрын
I'm not surprised the rod bearings fared fine. They get significantly higher oil pressure than the main bearings due to the centrifugal force slinging out outwards in the crank oil journals. Spinning at high rpm bumps that pressure up even higher.
@KevinATJumpWorks6 ай бұрын
Great video! I think you should have pulled the oil plug while the engine was running though, simulating an oil loss in drive.
@briang.70409 ай бұрын
Quick answer to the question will this work in the long term or does this mod has any benefits for my usual engine - NO I'm working for europes biggest manufactuer of industrial/engine bearings and was able to gain some knowlegde about this topic. It was proven many times in different studys, done by Dr.Frössel and other ginuses in the name of bearing and flow research. Any grove or significant low spot before or right in the point of the highest load of the bearing, no matter if its in the bearing or the crank jurnal, disturbs the flow and worsens the gain in pressure within the oil gap, yes that means even the oil feeding hole on your journals is causing these problems, thats why properly designed bearings only have a oil feeding slot in the unloaded bearing side, to maximize the working bearing surface. However you might improve your temperature in your bearing, since the added turblances improve mixing of hotter and colder oil layers, and maybe improve lubrication in situations with not enough oil in the bearing, like a start up after weeks of sitting around. But apart from this, your engine bearing, wich is a profile (lemon shape) bearing, will lose a lot of its load capacity and functionality depending on rpm and viscosity. The only way this modification would work out, would be a pressurised application - a hydrostatic bearing type, in wich the dimples and grooves on the load side have an own pressurized system, that runs with a much higher oil pressure than the oil support itself. But thats a whole nother topic and too much to explain here. Greetings Brian
@orbitnick27819 ай бұрын
Yall should try installing and automatic trans behind a clutch
@Jonodrew12865 ай бұрын
More grooves would actually make the bearing matrix weaker - have seen bearing material go like crazy paving with insufficient oil change duration. Also it was a good test - however even with an oil pump, crank and bearing change - there will now be fine metal fragments floating about - hence the Main going - also failure usually occurs furthest from the oil pump. Finally that No.4 b/end journal in that rod would also be out by 1 thousandth or so and the edge loading would have altered - but it was a good test to see what oil starvation does to an engine - it can also destroy the Cam- Shaft journals 😮
@Eluderatnight9 ай бұрын
The criss cross grooves is for low rpm applications in a dirty environment using an oil drip.
@prevost86869 ай бұрын
I’ve never been on Tictok . If this is an example of the wisdom found there I don’t think I’ve missed anything.
@Tennesseemountainhomestead9 ай бұрын
If this was a thing, the auto manufacturers would have been doing it a long time ago
@bladfufu9 ай бұрын
The auto manufacturer want you to buy their cars, no to keep them indefinitely.
@Tennesseemountainhomestead9 ай бұрын
If you want some thing that is going to last, I can tell you this. By a Chevy Silverado 2500 or anything with the 6 L truck engine in it. I’ve had five of them since 2007 and driven them to 250,000 miles each Besides the one I’m driving right now that I’ve had since March 2019. It currently has 186,000 miles on it. The only thing I’ve ever done to any of the trucks is oil changes and routine maintenance. Never even had to change a set of spark plugs. And they usually only need one set of brakes. The only reason they get retired at 250,000 miles is because that’s when the company I work for switches them out. I take care of all the maintenance and drive them home every day.
@Tennesseemountainhomestead9 ай бұрын
And I would bet the rod bearings are not drilled and slotted
@robriot68826 ай бұрын
The other thing is the rods get lubrication from the mains. So doing this to the main bearings could reduce the oil pressure to the rods, resulting in shorter lifespan for the rods
@dhrida55189 ай бұрын
This had no outcome because it was tested without oil and the channels are just to improve oil delivery, best way to test it properly is by spinning the crank above the rpms it was designed for and you must use oil and the oil must be at ideal temperature so at least 80celcius, still very interesting that it held the same amount of time.
@Threads12208 ай бұрын
I have never heard of cutting scratches into the bearings but I have heard of old-school sbc guys drilling extra holes in them chanfuring them and then grind a slit into block to supply oil to those holes
@Anarchy-Is-Liberty5 ай бұрын
I would give a "big" thumbs up, but there's only one size available!
@bertgrau39348 ай бұрын
There's a lot of other things that can make the engine stop, not just the crankshaft bearings. Like the rocker arms could seize, or break, valves could also seize in the open position.
@lincolnbliss48859 ай бұрын
Try adding paddles to the crank to throw the oil around better
@jttech449 ай бұрын
@@danielleclark-zack864 It's not a theory
@Homme_Pur9 ай бұрын
you guys could try putting these in an engine that's used for the breaks testing or other non engine related stuff, just to see if it causes anything after a few thousands kms (maybe 5 to 10 thousands ?)
@WilTK49 ай бұрын
well, some brands in latin america sell VW EA827 (which is a very very common engine from Brazil or Argentina), have carved bearings for that engine, while some others dont, or only one half may be carved and the other not
@felixlafuente97149 ай бұрын
Sugestion: Can you make and test a toilette paper oil filter?
@anonymous-tn6ij6 ай бұрын
not a very controlled experiment if you’re by using the same crank for one, the grooves are supposed to hold more oil on the crank journals so that’s the idea draining the oil takes away the idea and how do you get oil pressure with all those groups between the bearings in the crank
@peterlonter90539 ай бұрын
a very well explained video about how to be more cautious .technically explained .thanks for video .
@KentuckyHillbilly9 ай бұрын
Grooving the bottom shell takes away 20 percent of the bearing's load-bearing area. Forces are trying to drive the crank down out of the engine, so that's critical! Because bearings taper out from the center towards the parting line, 360 degree grooves actually gives you an avenue to loose pressure. today's stockers and high end engines now only have just a 120-degree upper groove. guess I will add in the entire... right way to do this.
@NitroGnome9 ай бұрын
This type of bearing solution works only with extreme high oil pressures and pocket's need to be larger.... it is called hydrostatic bearing