I like how older hitachi tools look like some living creatures, like aliens :)

Круто Хитачи! Отличное видео, спасибо автор

Sir you solder the commutator motor getting over heating solder loose please next time connected the wire motor perfectly and nice restoration sir thank you so much for the sharing this video sir 😊😊❤

Yeah we need more people like you... it would be a shame to let these old tools go to waste ❤❤

Лучший, спасибо за потраченное время!!! Здоровья тебе и твоей семье!!!

A great restoration!! Another great job. 👏👏👏

Watching your videos is fair and enjoyable

بارك الله فيك اخي الكريم انته حقا مهندس ممتاز ❤❤❤❤❤❤❤❤

Hello mister beautiful restoration beautifully restored good job well done

Nice job !

Great job! It looks brand new.

nicely done sir!

Siempre al rescate de herramientas rotas y/ o abandonadas buen trabajo 👍

Hola amigo buen video me gustó mucho bendiciones para ti y tu proyecto asta pronto 👍👍🇭🇳🇭🇳

Hello my friend, well done, I like you

Great restoration

Bom trabalho 👍 👍

very good.

Wow

What a great show.

Hey, how come you don’t use the ultrasonic cleaner anymore?

Finally sandblasting footage! It's a rarity on this channel

hồi phục quá tốt

Я дома использую только шуруповерты Хитачи, на li-ion, не спеша буду покупать другой инструмент от Хитачи

Jolie travail

шикарное восстановление, но на последних кадрах болезнь всех лобзиков среднего сегмента как и низкого, пилку заваливает

Excellent job Well Done

Огонь 🔥

👋👋👋

How to make work from home

Look, someone from Brazil who lives in the affected areas of Rio Grande do Sul could send/donate some tools that were submerged during the flood for you to recover.

good job. Cordless brush motor tools should come back, they are better in many ways.

Por que o carregador da bateria faz aquele som?

Start motor engine restoration, please

I'm not so sure how long that repaired motor will last... the g-forces on that solder joint when the motor is spinning at high speed would tend to try to rip the joint apart again, and I suspect the soft solder will hold for a while, but will eventually give way under the strain. Expect it to fail again in a few months under normal use. The motors are originally built with the wire wrapped around something to keep it secure (a post or a tag of some kind, often squeezed tight and sometimes then blobbed with solder as well. I've never actually done this particular repair but the engineer in me is screaming at the thing saying "Noooooo its not going to hold for very long!" If anyone has any actual data about how long such a joint holds under reasonable use then please come forward, but at the moment, I am skeptical.

🌲Nice BLUE CELLS. 🌲WHO IS MANUFACTURER.

Who is CKS?

plmds, mlk nem p´ra limpar antes de colocar as celulas novas na bateria .....

👍😎🍺🍩🛠️🗜️

Grandpa responds: "Back in my day, we didn’t have fancy recycle shops. We had common sense and took care of our tools. They don’t make things like they used to. I remember when a tool would last you a lifetime. You’d buy a jigsaw, and it’d be there for you through thick and thin, not like this modern junk that falls apart if you look at it wrong. Back in my day, when something broke, you didn’t just toss it. You rolled up your sleeves and fixed it. Tools were made to be repaired, not replaced. You had real craftsmanship, not this cheap plastic nonsense they churn out now. And another thing, back then, you didn't need a degree to understand how your tools worked. You knew how to take them apart and put them back together because they were built with the user in mind. Nowadays, everything’s so complicated with all these electronic parts and special batteries. It's like they're designed to fail just to keep you buying more. I remember fixing my old Black & Decker jigsaw. That thing was a beast! Built like a tank and ran like one too. None of this lightweight, battery-operated stuff. You plugged it in, and it just worked. For decades! If something went wrong, you grabbed a wrench, not a KZfaq tutorial. These kids today don’t know the first thing about real tools. They just buy new ones whenever something goes wrong. It’s a throwaway culture, and it drives me nuts. Nobody has any pride in their work anymore. Everything’s disposable, including people’s skills. In conclusion, good job, Gear Show, for trying to keep the old ways alive. Maybe there's a sliver of hope for this generation, but they’ve got a long way to go before they understand what real quality is. Back in my day, we didn’t just use tools, we respected them. And they respected us back."

9:29 Ха, чо за прикол?