That's actually quite dangerous to have a difficult to reach push button. Usually those devices on battery have two buttons, one of them is a trigger that must be pressed for it to keep working. If not... Good luck catching it when it falls...

the fact that you made a more powerful motor out of two smaller ones is extraordinary.

@13:23 That bearing was onstalled incorrectly. The friction was on outer wall and you pressed in from the inner wall. Therefore the force has to transfer trough those ballbearings. Ballbearings will damage the groove where they should rotate if pressed sideways like you did.

I had a lot of old pipes and rebar to cut up and from what I read kzfaq.infoUgkxPDBfLu68o58Aw85O_J-zIFfjJARBhp-3 this would be the tool for the job. Since I had never used one, I watched a couple of youtube videos and I'm so glad I did. Some really good safety tips, which I followed, and this tool did a splendid job. One good thing to know is the weight of the tool puts just about the right amount of pressure on the metal I was cutting, so I didn't have to use a lot of pressure, which is more likely to jam the tool. It made fast work of my job.

Crazy amount of work, but the result is really amazing

it's quite a while since i stopping by and this channel has transformed to remaking instead of just restoring things.

Not really sure i like the way the bearings were pressed but the overall project and the fact you wound the motor is impressive.

Wow wasn’t expecting you to combine 2 brushless motors! 👍👍👍

Привет из России. За проделанную работу лайк. Время и ресурсы потраченные на переделку не стоят того, проще купить новую.

You're making such a big deal out of this. Respect to you.

i love this series from you the way you connect the brushless motor exactly what i have thought about it

This is quite a great job. My respects.

Good job with all the best information and knowledge 👍

Всё сделано классно, за исключением трех моментов. Нельзя запрессовывать подшипник за внутреннюю обойму, статор мотора должен фиксироваться к корпусу надёжно, иначе его будет проворачивать и кнопку с фиксацией на такие инструменты ставить нельзя, это очень опасно.

Hello mister this converted is one of best work beautifully done

gracias a tus videos. de restauracion aprendi mucho.de todas las formas q vi de tranformar un amoladora 220 a una electrica de 18 v me quedo con esta version de video.las demas vi no llegaban a la fuerza q muestras esta.y eso q tambien tenian torno y todo las herramientas para hacer dicho proyecto.gracias a tu canal las cosas q encuentro las puedo restaurar mejor sume mucha experiencia,uno de lo mejorsitos canales q vi de este nicho

nice. I've been waiting for it all the time but only you do this

its amazing how nice you made this conversion and to know exactly how many turns on the wire to make, you definitely know your stuff. That said it probably would have been easier to buy an angle grinder of this type.

I have been following you for a relatively long time. I am one of your followers from Egypt. I like the type of your videos

Мне понравилось когда перегородку корпуса пилил ножовкой,заодно и провод перепилил от статора))))

Wow you are the best DIYers👍👍👍☺️

Now that's some next level stuff

Incredible work, I continue to be amazed by your work with motors.

Ogladałem do konca jestem pełen podziwu dla twojej wiedzy😮

Amazing process

Un trabajo titánico , me parece increíble lo que haces , enhorabuena por el canal. Muchas gracias por compartir , un saludo.

Que trabajó más ingenioso, muy buena idea. Felicitaciones

Excellent video 💕💕

Parabéns o resultado final ficou espetacular, houve muita engenharia, e ficou sob medida

Nice info ,thanks for sharing it :)

Awesome, I’m gonna have to try this

I love what you did here - Well done - Bravo !

Fantastic work, but the lack of a safety release kind of surprised me in this build. Agreed about the flat button to prevent accidental on situations, but that also makes it difficult to turn off too.

Ignore all negative comments because you completed an amazing transformation from a clapped out, burned out piece of junk to a fresh cleanly built cordless, brushless, powerful angle grinder which almost all of the people who wrote negative comments wouldn’t be able to do themselves. It’s not always about time and cost affective value, it is a project with 100% results so ignore the haters and I am not slating the ones who have pointed out of some alternative ways which may or may not help you in future projects I don’t know, all I am saying is you have done a great job and I for one took a lot of positives from it, well done

C’est excellent pour l’explication 👍✌️👏

That's powerful man😮

Very nice excellent work congratuñation

13:20 The outside must be pressed, not the inside. Pressing the inside during installation, it can cause a damaged bearing 🙏

이정도 기술이면 거의 모든 기계를 고치겠네요 침 잘하시네요

Great work 👏👏

This is an enviable accomplishment! Bravo.

Di dukung dengan pekerjaan yang sangat baik dan rapi hasil nya pun memuaskan... Selamat buat anda....

I genuinly love the fact when making that L bracket thing fit that they used annother angle grinder to do the work. It's fun because while you know the same result could be achieved another way it shows you that said tool type is useful, nicer, or just an easier way to do the same thing.

Un trabajo titánico , me parece increíble

Very good work 👍

عمل متقن و رائع...واصل ابداعك يا فنان

UN PROFECIONAL FELICITACIONES PORQUE TODO EL PROCESO DE PRINCIPIO A FIN EXELENTE

Nice work!

Just love your Videos. Great Job

wow! kreatif banget ya mantap dan sangat terinspirasi 👍👍👍

you're just amazing. respect.

Wooww great modivication

great! I like it very much, I have learned it!😊

Excellent work 👍👍👍Thank you for sharing. Be safe🇨🇦

Great work.

Nice work

First conversion of this type I've seen. Nice. Probably the best quality 18v angle grinder out there. The older tools are just better. No shitty overload/battery/stall protection like most. Hate that on my m12 fuel die grinder, it just stops, I wish it would just bog down, instead it unexpectedly stalls suddenly. Annoying. Nice work man!

Congratulations Gear Show on this successfully completed restoration...❤️❤️❤️❤️🤟🤟🤟😘😘😘

建議電池座的方向換一下比較順手，目前電池方向和砂輪片同方向，使用起來某些角度會卡到電池，切割時的火花也可能噴到電池、可以參考makita 電動砂輪機的設計比較順手，個人小小建議

Master at his craft

Gratidão GearShow! Ficou top!

I enjoy watching and following your videos. Where do you supply/buy the empty battery boxes and equipment you use?

Nice adapting

I love your brushless motor conservation series🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰🥰😃😃😃😃😃😃😃😃😃😃😃😃😃😃😃😃😃😃😃😃

Great work ,,, could you publish the motors specifications or link ? also the controler 👍

You're a lunatic. I like your style!

the set of stator core sheets should not be shorted, and you put it in a steel sleeve. This is the first. Secondly, bearings cannot be pressed into the inner race! Third, the wire needs to be wound carefully without twists or creases and as evenly as possible, this is not the case with you. Fourth, the general impression is that you have never held a soldering iron in your hands, not to mention rewinding motors... And everything turned out easy and simple for you))) I don’t believe you)

thank you teacher❤❤❤ Great job, thank you brother. You are so talented

Beau travail !!! Merci de partager !!

what prevents the motor from rotating itself? I see you use a setscrew between sleeve and stator, but what makes it hold on to housing?

Very very good😍 nice

you are ingenious

Excellent Bravo 👏 You are really master Perfect 👍

Reducer bearing was installed incorrectly, You should push on the outer shell not inner. Overall not bad.

Good job sir,you'rgood invintor,

When you press in bearings, you press on the outer race, not the inner race. this avoids damage to either race and/or the ball bearings in between. Other wise it was a nice job (ignoring the little boo boo of cut leads.)!

Exelente video y genio total.

the best homemade work！

Yes very good! Only you must change the Type of switch for SAFETY precaution

Always Enjoy Watching Your Work

Too many negative comments without work? You should be ashamed. Keep up the good work, I'm waiting for your next amazing work.

Good job, keep it up.

Well done, as always surprised us with his work 😊

Impresionante trabajo.

Good work. An idea for second video: buy a pwm controller and pwm driven motor driver as for rc quadrocopter, with soft start, soft and immediately stop. And good idea for safety is to add a body button to stop instrument if you loose your hand over it.

23:01 From the visual pleasure this is called great work

Really good!

Great Job!

Amazing work Mr gear show 🇰🇭🇰🇭🇰🇭❤️❤️❤️❤️sending love from Cambodia 🇰🇭

i was thinking of this and u made it

Congratulations for sharing and brilliance. I ask you where did you get two scooters brushless? or at least a link to buy them. Thank you

Keren pengerjaan yg sangat apik

good job

nice job overall the only problem with this it's that after purchase all the necessary parts it's end up costing more than a very new cordless grinder all together plus all the work to putting everything together . But on the other hand it it's a very good to have something custum that no body else has and I really like that .

Simply the BEST!!!!

I am not sure if the speed controler will last too long, especially if you force it. since it has to take the load of basicly two motors now. And usually these Controlers are used with switches wich gradually give power. All those on/offs at full power will burn it quick. It would be nice if you could use an RC testing switch wich can gradually increase power and set what speed you want. Also I am kind of a welder sometimes and i've been used the angle grinder to cut alot of metal. I've found the thin discs, the 1 mm ones to be best for cutting metal, they cut faster, cleaner, heating the material less and giving you a more precise cut. At first i thought those are only good for cutting thin metal sheets, but is good for anything you wanna cut. The only thing you have to be careful with when using them is when you cut tubes and thick pices of metal not to pinch the disc as you are grinding through the cut, those thin discs explode very fast. But even if they do if you have good eye protection and a cover for the disc you are safe. I think alot of people are afraid of those discs as they are so thin but once you learn to work with them, trust me, you will rarely use these 1.5, 2mm ones to cut anything.

brillian man

Wow very good

you're a champion!

I always jump right into the videos you publish. But this time was quite intrigued when you pressed the bearing in by pushing onto the inner ring. Why didn’t you use a socket or something so you avoid damaging it?