You answered every single question I had concerning the release bearing in one video, thanks!

Great video

Thank you!

Very informative thanks!

Amazing video! Thanks

where do you face the lobe of the bearing toward the fork or the shaft?

Thanks I 'm watching them all.

What would cause a guide tube to break off the transmission? I could not get my truck into gear while running, after I thoroughly bleed the hydraulic system and still could not get it into gear I pulled the trans. The guide tube has broken off completely. I am curious if this is why I could not shift into a gear.

After long driving,car stop over night.nextday ,my clutch pedal was at the floor.what l always do is lever the fork then sleeve cy rod push back and hold it possion, now free to moves the gears.what the cause?

Not a happy camper. Purchased a clutch kit for 89 S10 pickup. Clutch is very touchy and hard to drive. Don't recall having this issue with any other clutch I installed. New flywheel and pressure plate were cleaned with brake cleaner Sad.

Do you want a return spring on the clutch Fork? Is that bearing supposed to ride on the pressure plate constantly?

This godsend ❤

Just got clutch installec on 89 s10 pickup with 2 wd. Watched video prior to putting trans in. Pedal seem to light. Old clutch felt better. It seems to easy to push pedal it. A new clutch should have more resistance than what it does. Have yet to start truck up. So I don't know if it releases right. Crossing my fingers.

Might sound weird but I'm having problems with my clutch where I can bleed it and when I try to put it in gear the pedal goes have way and does not go any farther

have a 67 c50 292 6 cly chevrolet will not go in gear tell me what wrong with it

you referred me to this video with my question about a hard to push pedal. I forgot to mention that sometimes the pedal squeaks when I push it. does that indicate a particular problem?

Just put transmission in there was no release bearing clip in the clutch kit it has been installed without any clip do not remember seeing one on disasembly it is a 1988 K1500 is it possible there is none.

I have a 95 c1500 4.3 2wd i don't remember my pivot ball looking like that. I don't thibk its removable either? I can move the clutch for by hand but it doesn't retract. Is it supposed to do that?

Quick question for you do you know if this Is the same procedure for a 1992 chevy s10 4x4 4.3

have not adjusted clutch or finished job

X,x omg you answered my doubts

I just replace the clutch kit on a 2000 mustang gt v8 five speed and the clutch pedal its too hard and the gears wont engage please help

hi listen what other thing i can use for mi put the clutch in the center because mi no have the special tool and mi no finded on the store in this island if posible yuo can buy one for me please

good video

tks

Does anyone know what might be causing a ton of vibration on the clutch pedal at idle? The vibration has been traced all the way down to the throwout fork. It has been an issue since previous owner. I replaced the clutch & throwout bearing - and the issue still persists. Thanks! 1981 trans am 305 Borg Warner Super T10 4 speed manual

Just learned all this the hard way. Too bad I didn't see this earlier. Is there a correct way to install the bearing re the cam on the bearing? I've been told it should face the fork but in your video it faces away from the fork

Called tech support this morning and spoke with Tony I told him a number of times that I had a 2 wd Chevy S10 pickup with a 4 cylinder engine. I told him the clutch is very touchy. He kept asking the part number which I had a my garage across town. The number is 90191. The number below that MU 1904-1. I told him I would call back when I get the part number. He then rudely hung up on me. I went around the block yesterday and the clutch was so touchy and jerking my truck to the point my camper top came loose and I got pulled over. I want my old clutch back. You shouldn't be allowed to be called perfection. No excuse for this at all.

In spanish please