Great to see you're back at making content, and I'm also interested in the relationship between VLAN's and bridges, so I'll wait for that video. Thanks again

You should always "talk about Cisco when showcasing MikroTik". It's important to see how different brands interact in a production ecosystem. It's been the exception rather than the rule (in my experience) to have a company only use one brand. It's usually something along the lines of MikroTik Routers, Cisco Switches, and Ruckus/Ubiquiti/Juniper access points all in the same building.

Just picked up an RB5009 for my home network, it's a steep learning curve! Ultimately I want to set up a VLAN connection between my VDSL modem and the router for WAN, since the physical interface connecting them is shared by one of my APs, this was helpful.

Thank you so much for posting this video. I understand Vlans but couldn't see how to set them up.

Thank you so much for the help. I was trying to get this done with a Aruba Switch for a while but didn't find the time. Now its seems to be pulling the proper Ip adress from DHCP. thanks again

You keep knocking it out of the park with quality content covering Mikrotik.

Super clear and simple to understand! Many thanks!

Thanks for this great intro - much appreciated!

Again another great and informative video on VLANs. Thanks!

I'm glad to see you! Thanks for the new knowledge! but I have a question about vlan!

Being fairly new to Mikrotik I am impressed by your pleasant presentation to teaching Mikrotik Setup

very good video! i am watching the entire playlist and practicing everytime!

In regards to radio,... They would be the equivalent of CB Sidebands.

Thank you for the helpful videos! Tomorrow I'll be doing my first VLAN deployment with Mikrotik RB4011 and CRS switches. It would be interesting if you could add an explanation about the /bridge interface vlans. It has been quite tricky for confusing for me.

Nicely done, sir!

Thank you for your great work, which you bring to us with your channel. In case you have time and would like one day to prepare a lab, where you have ccr as a router, and crs3XX series with router OS on it which plays as a L2 device, and distribute vlans, to hypotetical hypervisors, that would be a great help, as they slightly differs within it's configuration between series of CRS1XX, CRS2XX and 3XX, which is quite confusing to grasp for a begginer like me. Thx again !

One more great video about networking. Best regards.

Can you zoom in on the WinBox and other graphics? In a few videos of yours you keep them at such a small size that it is really so difficult to make out. It really would make a lot of difference. In any case, thanks for putting out these videos.

You can do the VLAN using the bridge interface too. I normally use the interface functions when I want to rename the interface or bond the interface.

Great job. Thank you.

Thank you for the great video!

explained nicely. I have two DSL connections which i want to send over a single wireless link and segregate at the receiving end. How can i achieve this using two RB450s which i have.? I somehow got the idea from your video that i need to create two VLANs for the two connections but how do i create a trunk port to carry both those VLANs on mikrotik ??? Please guide me. thanks

Thanks you for this very nice explanation. You are quite correct, having completed MTCNA, there is no VLAN info included. I wish to extend my WIFI that is set up with different SSID/subnets for different users. - using another Mikrotik device. I think VLAN is the "approved" way to do this. I am also using bridges for each network so I am guessing you can add a newly created VLAN interface to the bridge??

Thank you for great videos. I have a question: how do you separate wireless devices with VLANs?

Really appreciate your excellent content on things Mikrotik. I have the Mikrotik RB4011 and CRS328 and wish to set up multiple VLANs. After watching so many videos and reading so many forums etc, I am still not sure whether it's best to create the VLANs on the switch or router (as both have RouterOS) - my gut tells me the switch, with the router 'just' doing Firewall and interVLAN routing as required. Appreciate your thoughts. Many thanks.

Hi Network Berg, I'm trying to autodiscover my network wired printer from a different vlan and subnet. My printer that is on a specific vlan, this isn't bridged and is assigned on a specific interface and I'm trying to find it over a wireless connection provided by the same Mikrotik (has its own antennas). From what I've seen, multicast packets don't go through, even activating igmp proxy. I'm aware they are different broadcasts domains, but is there any way of acheiving this? I have also taken into account that multicast TTL is 1 and have attempted to increase it with a mangle rule. Note: between both nets there is a firewall general accept. No traffic is filtered. The printer can be manually added by ip.

Hi Berg, can you explain a little bit about PIM and IGMP protocol on mikrotik routers and how it's working?

Could we use any mikrotik switch as olt like fiber optical pon power out ?

Great Video! Thank you for this. I don't suppose you have managed to get QinQ working at all on ROS?

how to use 2 port VLAN Trunk port?

Hi Johnny van den Berg. In this video you show a software EVE (minute 2.51) with various MikroTik devices. How does that work? Have you also made a video? Is there a real RouteOS from Mikrotik behind the icons in the software? Can you insert and configure any number of MicroTik devices? I know a lot of questions, but you do it so well. I have now gone through almost all the videos. Thank you. Greetings Markus Hi Johnny van den Berg. In diesem Video zeigst Du eine Software EVE (Minute 2.51) mit verschiedensten MikroTik Geräten. Wie funkioniert das? Hast Du dazu auch ein Video gemacht? Liegt hinter den Icons in der Software ein reales RouteOS von Mikrotik? Kannst Du belibig viele MicroTik Endgeräte einfügen und konfigurieren? Ich weiß viele Fragen aber Du machst das so gut. Habe jetzt fast alle Videos durch. Dankeschön. Gruß Markus

amazing explanation

Im keep asking myself same question with trying and keep trying to acheive it . How to make egrees traffic for specific port untagged and same as ingrees to become tagged in bridged vlan ??

But this implementation of VLANs means using software capabilities of Router OS, not the hardware? There is another way to do it via bridges with VLAN filtering enabled, but now I'm quite confused

please post about MTU and MSS

Hi, you're videos are very well done. I know this is an older one but I have a MikroTik Cloud Router/Switch that I want to have act as a pass through distro switch, as in- it accepts two LAN inputs from my Cisco MX firewall, and will pass data from those two LANS onto the respective ports going to my access switches say top row is vlan 100 and bottom row is 200 etc. but without running DHCP since the firewall is handling it. It seems it has to be set up to divy out DHCP but I'm hoping I'm just missing something. I would just plug the access switches directly into the MX but there aren't enough ports. Would you point me to a video that explains that if it is possible? Thx in advance

so placing more vlans on a single physical interface behaves like a subinterface (int gi0/0.10) on a cisco rtr

Hi, thanks for the great video. I installed EVE NG so I could test my own network, where I have two Mikrotics. It's similar to what you say at the end of the video. I can assign an IP (but only to Ethernet, VLAN somehow not work). I can pinknut on the IP, but I can't open the 2nd router in Winbox. It is no longer in the video whether you can open it. Can you please tell me where the mistake is?

hi, is there an application for Mikrotik to learn like we do for Cisco on Packet tracer and build networks?

Which Cisco images did you use ?? I have some bin files and loaded them but they are not starting

How will it translate from vlan10 to vlan 1189

great content. Which software are you using for the simulation? kindly

Really like your video, liked and subbed... However, i will really appreciate it if you can answer how to convert or make an incoming LAN (eg; 192.168.1.20/24 without a VLAN ID) to a VLAN and add it to your trunk in mikrotik. The way of doing it in cisco seems easier and clear but not in mikrotik. Thanks for your swift and concise response and God bless.

what is the name of this sofware (Web GUI) you are using ?

Can someone from your team help me to create Vlan in my existing mikrotik? I will give you network diagram and I need it badly.

nice video overall, however you left me with more questions than answers

What was that Cisco network topology tool you are using?

what is that tool you are using to virtually set all of this up? I would love something like this to practice on.

can i use ordinary switch to work for vlans?

What platform is use for lab setup ? Is this GNS3 ?

Hi , why we use /30 subnetting in mikrotik ?

Can i run vlan on bridge ?

I downvoted this video because 90% of the presentation screen is empty and the useful informationnia so tiny that I have to zoom in to follow. I get it: you have a huge monitor, good luck with that!