@SymphonieDuVide Жыл бұрын
Thanks a lot !!! Works perfectly !
@JWNZ Жыл бұрын
Awesome!
@ccamilocr 6 ай бұрын
Gracias un saludo desde Colombia funciono perfectamente
@JWNZ 5 ай бұрын
¡Eso es increíble, hola desde Nueva Zelanda!
@jankcow6714 9 ай бұрын
You did not mention that the programming jig need a button and you need to press it while plugging it in to flash ESP1
@JWNZ 9 ай бұрын
Depends what jig you have. Usually if you have a cheaper one you just need to short gpi0 to gnd.
@mun5660 2 жыл бұрын
I purchase an esp-01 recently but it isn't responding to AT commands or my project codes...Tried using several flashing tools to update it but not working. Could you help please
@grindfi 2 жыл бұрын
try shorting these pins while flashing: with the antenna at the top, right lowest most pin shorted with the third pin to the left
@JWNZ 2 жыл бұрын
Have you connected the enable pin to VCC? It is marked EN on the board.
@jstro-hobbytech 2 жыл бұрын
good video man. that's a Grove connector I think because they were thr ones who started using that for power. I'm going to make my own breakout board for the esp I think. the wife wants custom lighting for our new kitchen and I want a multi output psu to go with my new siglent scope so I'm going to use an esp32 with a remote for the main controller then use the esp01 modules as simple wireless daisy chains. I'm not sure if I'm gonna use wled or just code my own custom simplistic set of effects because a career woman can't be having the bouncing ball effect going off while she shows the new kitchen off lol
@JWNZ 2 жыл бұрын
Have a look at fastLED I used it in this project kzfaq.info/get/bejne/nLN5e7Bqv5zUlac.html
@muhammadisa6954 8 ай бұрын
If I use LED strips that are not RGB, aka 1 color only. Can I use this program?
@JWNZ 8 ай бұрын
Generally no. Mono strips usually do not have the neopixels to translate the commands from the controller. They will just have two connections for either power pin, no third pin for data.
@muhammadisa6954 8 ай бұрын
Can I use this wled program together with esp-01 with a 10-meter LED strip?
@JWNZ 8 ай бұрын
@@muhammadisa6954 the length of the strip is not so much as important as the pixel density. You should be able to run around 512 leds on an ESP8266
@SpeccyMan Жыл бұрын
I bought a cheap mood light from Poundstretcher (and yes it was cheap and nasty but all I really wanted was the enclosure) and ripped out its innards and replaced them with this system and a 12 segment neopixel ring. Now it actually deserves to be called a mood light. 😁
@JWNZ Жыл бұрын
Instructables has a lighting contest on at the moment. You should submit your project! www.instructables.com/contest/lamps22/
@mrhide7403 Жыл бұрын
Which GPIO pin I need to connect with data pin?
@JWNZ Жыл бұрын
It is GPIO 1 but I really recommend you just get the daughter board.
@gudelauneee Жыл бұрын
Every time i disconnect the power supply the settings are gone. Do you know Why?
@JWNZ Жыл бұрын
Wifi settings are gone or just the light settings?
@gudelauneee Жыл бұрын
@@JWNZ everything is gone. When i Flash the esp 01 file instead of the 8266 file the Setting wont reset but it will restart randomly
@gudelauneee Жыл бұрын
@@JWNZ testet another when i try to connect to the AP it blinks and the connection failed
@JWNZ Жыл бұрын
@@gudelauneee I have had the resetting issue and I had to erase the flash contents and start again with esptool. This can also be insufficient current. How are you powering it?
@gudelauneee Жыл бұрын
@@JWNZ With a usb Smartphone Charger 😅 2 ampere. Nur its only 73 LEDs
@gudelauneee 2 жыл бұрын
i have flashed the wled software over the website. when i power it on i can't find a wlan ap. do you know why?
@JWNZ 2 жыл бұрын
Did you flash a esp-01? Sorry haven't done it this way. AFAIK it isn't possible to OTA update a esp-01 due to the ram size.
@gudelauneee 2 жыл бұрын
@@JWNZ yes that's True. I flashed with the flasher now and it works Flawless
@jstro-hobbytech 2 жыл бұрын
@@JWNZ the on board flash has to be >=512kb. just read the data sheet haha
@JWNZ 2 жыл бұрын
@@jstro-hobbytech That is for the esp-01 the esp-01s is 1MB. You can remove features from WLED for OTA to work.
@FabianPfau Жыл бұрын
I am using an ESP-01 with WLED v0.13.0-b6. Anyone have the same problem with random restarts? Sometimes several times in an hour, sometimes not once the entire evening. After restart the device fallback to preset 1 and works fine again. (till the next random restart)
@JWNZ Жыл бұрын
Yes I have had this. I don't know why it was doing it but a full erase of the esp-01 with esptool and a reflash seemed to fix it.
Chris Maher
Рет қаралды 198 М.
TeMa ↯ Самоделки, DIY, Arduino
Рет қаралды 13 М.
Smart Home Circle
Рет қаралды 11 М.