Just trying my best with my busy life. Hopefully post more soon. Glad you got a krink. I sadly sold mine to fund other things but that’s one I miss a lot.

I kept mine stock. But replacing them I think is pretty close to real Glock and/or other airsoft versions

I sent the slide to be rmr cut. It’s not just drilled. It’s also cut into the slide

@@gbbrworld4759 Thank you for the reply, I meant the drill bit you stuck inside the nozzle arm

@@alexal1232 ohhh I used a cheap black oxide type of drill bit.

@@gbbrworld4759 understood, thank you

This only works for ghk Glock fyi

It’s just a flat 2mm cut with two holes drilled and tapped. On the ghk fb group I have more pics of it without rmr

Safariland 6354DO for g34 with x300

The rmr just helps with quicker aiming and easier aiming. Also need it to shoot under my nvgs.

About 280-300 with .25. I have to chrono mine but that’s what my friends ghk chronos at with co2.

It’s 3mm deep cut with the holes for the rmr being 5mm deep. If you want find my posts in the ghk ghk g17 FB group and send me a message so I can send the blueprints

​@@gbbrworld4759 Ok, no problem

No the firing mechanism is completely different

I think it is. Only issue I had was the nozzle but it was a easy mod and I love shooting this thing.

It´s worth it for sure. I got mine for a very cheap price, but I wouldnt pay over 350€ personally

@@lilbenztruck just out of curiosity, how much did you pay for it?

@@alexal1232 it was 280€ I think

@@lilbenztruck lucky you, I only found mine last week for 295€

The slide was milled and drilled for the rmr almost like a real rmr cut on a real pistol.

USA

You can but not recommended. The co2 kit comes with new nozzle to help regulate the higher pressure co2. Also the recoil spring and guide rod is stiffer to also handle the faster and harder kick. They also include a new hop up/inner which idk why but it’s beefier than green gas

@@gbbrworld4759 ah ok thanks. Are the modifications hard to make if you don‘t have any experience with modifying airsofts?

@@harald2101 samoon has co2 conversion kit and I’ve installed a couple. Takes like 15 mins. And yes I do. I do lots of gbb tech work

@@gbbrworld4759 sorry to bother again, but what is this kit called exactly? i found the "enhanced kit" and the "ultimate kit". here in germany it costs about 200€. that can't bve right, can it?

@@harald2101 the co2 conversion kit is called ultimate kit. And yeah it’s a bit expensive but comes with a lot of tougher made parts.

Lakeside protofab LLC

@@gbbrworld4759 what screw type did he tap it to? 4-40 etc?

@@ezzyzhoo5139 M3

It’s a real trijicon rmr rm06

2mm

@@gbbrworld4759 OK thank you. If I remove 2mm, there will be no hole to the cylinder head yet?

@@gbbrworld4759 And to what depth should the holes for screwing the collimator be drilled? did not go out?

@@28karateka I think the holes for the screws is about 6mm

@@gbbrworld4759 Thank you very much for your helpful answers. I have one more question ... are the screws with which you screwed the collimator M2.5 or M3?

Found a machinist online. He’s located in Illinois

@@gbbrworld4759 was it somone who dose guns often? and did you have to give him specs or anything

@@auschris9296 yeah he does guns and other things but i have home schematic for the cut. It’s pretty simple cut. Only 2mm depth and two drilled and tapped holes

@@DataLog it performs better in colder weather, stronger recoil and cycles faster. The fps is still the same as running greengas. It actually might be shooting lower fps than greengas