Yep! You hit the mail on the head. The AT Pro is not that hard to set up if you know what you are doing. You hit all the key points. I would recommend everyone follow your advice to a T. The key to ocean hunting is to manually ground balance after you first auto ground balance it and to tune it to less than what it reads into auto by about 3 points or thereabouts. The ATP should then run quiet or just minimum noise. It works best in flat calm swimming areas. Wear Grey Ghost earphones instead of the crappy blue ones Garrett sells. GL & HH!

Great info! Been working with AT Pro for a long time, great machine but never reset it yet.. Couple of tips for yall: Number 9 clean your coil protector, especially after a water or sea search. Number 10 switch off your mobile phone (double usefull cause your lady can't mess up your search session :)) Number 11 high voltage cables might disturb your signals.. Happy hunting..

Thank you holding the power button to reset it fixed my buzzing noise!!!!!🎉 subscribed

Thanks so much. I brought my AT Pro with me to the UK and after detecting in saltwater (bad idea with this machine, obviously) it started giving me chatter. The chatter never went away. With your permission, I'd like to make a video explaining these steps on how to fix it to my subscribers, and of course i'd give you full credit as you deserve it. Please let me know, I want to go detecting tomorrow here in the UK before i head back to the states, thanks!

I am VERY impressed with your COMPLETE mastery of this machine. My hat's off to you pal.

Brilliant help! Will try this later as mine chatters on start up for a few minutes. Greets from the UK :)

Thanks for this! Very helpful! One more to add might be the simplest explanation of all...replace your batteries. I've had weird chatter start up before only to realize that my battery bars were running low.

Thank you sir! I subscribed and thanks for the help! Your advice helped me diagnose my detector i had for only 3 days! Afterwards from your help I found 2 more pennies with the AT PRO

Thanks! Excellent advice on the manual ground balance....I'm going to try that next time at an ocean beach.

I had this machine for two a half years great info never stop learning thanks alote

Great stuff. I get a lot of chatter on my at. I use some of those but forgot about the reset and the frequency change! Thanks. Heading out this weekend!

Thank you for sharing those 8 ideas. Very useful and very easy.

I use that chatter as a ringtone on my phone.

Good tips! I like the loose cable tip...

Great tips - thank you!

Thanks for this helpful info!

You are the man sir you taught me and my father so much

Great stuff here buddy. Thanks for sharing this.

Great video. I have the at pro and still getting used to. My first detector was an ace 250 and I SWEAR I've found more stuff with. Obviously still learning the at pro

Great info. Thanks a lot man.

Thank you

Great video. You helped me figure out my issue while at the beach. You saved my day man. Truly a great video.

Greetings from Newport News! I really appreciate these tips. I am not digging yet but am considering this detector or the AT Max.

Omg the reset workED!! Thanks Sir!!👍

Great tips, thanks!

Thanks!

Great video!

Great info. still important and helpful today

I like the “coin” setting. I found hundreds of pieces of aluminum pop cans .

Great tips!

Oooohhhhh....you just fix my at bro.!!!and save me a lot of time,subscribed and thumb up

Great Video! Thanks!!

Great video, thank you very much.

Sir Thanks! Excellent .

Thanks 😍😍

Great thanks 👏

GREAT tips THANKS and THANKS for all YOUR videos THERE great.

I want to thank you for your tips that are very helpful loose connector that's all it was your awesome something simple as that overlook still learning

Thank you for the info I just purchased a machine and thought it was broken all it needed was a reset

Some good info thanks for the video.

Very helpful thanks

Great tips.

Mine's coming ups tommorow!

Thank you for sharing this video. I ordered an AT PRO yesterday. Wondering how long it will take to figure out all the settings etc...

Thanks a lot. I needed to see this. I have a White's XLT. Do you have a video for those?

Thanks this will help with my new AT Max I believe.

great video ..

I assume since my at max even goes crazy when there is no coil connected. I assume the control box is euchered eh?

Note: my pro would shut off when I laid it down. Sent it in and AT reworked the whole unit free of charge. Now that’s customer support!

If you have some cousins from Chadbourn, N.C. You and I might be cousins. There are a lot of Andrews running around both North and South Carolina I have never met! I live in South Florida and hunt the beaches every 2-3 days. Not a lot of treasure, but every now and then a ring will turn up.

Does using a different frequency put less depth on your machine?

If your coils cracked. This wont work. But check the coil. That's another one. That was my problem yesterday.

I had similarly problem with 2 detector no more garret at max my next nox 800

gig master is that a Nel hunter coil

Great Video, Gig! I've been missing your videos and was worried about you. But ends up i was unsubsidized, somehow. Fixed that!

i can't ground balance on ace300i

i had some that the cabel to the coil was broken , it gave the same effect totaly haewire

Hi Gigmaster do you change your coil on a regular basis? And how long does a coil last normally? Thanks Ben

I'm new I did it 🤪

Add sand and dirt in your coil cover.

Shouldnt your cable be closer to shaft...yours is just flappin around

big like

Just got my at pro .wish waited for the max.does the pro go on salt waters

My at pro is acting weird when I plug in the headphones. Any advice.

The coil cover 2 when you're hunting at the beach and sand and other things get trapped between the coil and the cover so cleaning that out may help

Great video thanks for the info I started having a problem with my AT PRO, yesterday every time I would set it down to dig a target it would shut off, has anyone had this problem ? and I also put new batteries in and it still cut off any help would be greatly appreciated, Thanks, ( I also subbed your channel )

I got a garrett ace 150 that just clicks nothing else no screen nothing any ideas

Number 10. Remove the coil cover and clean it and the bottom of the coil.

I had the misfortune to buy one of these machines from eBay £649 what a overpriced piece of junk I sold it after two detecting trips for £300 🤬

I know how to get rid of the chatter junk it.