There's also Triple Thick which I don't care for. You can't over fill your projects and always make sure to spread it to the edges, also use a pin to pop the bubbles and never shake the bottle. Dimensional Magic is my favorite and nothing I've made stays sticky or turns yellow, even jewelry. I've just made a lot of things with this so hoping it helps someone.

Good to know, thanks for posting. This is a issue with my projects so this is a real time and money saver.

THANK YOU TONS for doing this video!!! This was much needed information! I hit the subscribe button and I am here to watch many more. I am a beader and jewelry maker who wants to glue charms in some things but do not want to go with resin. THANKS AGAIN Plus my Hubby loves that I was watching someone who had fart in his name, we are 50 y.o and he still giggles like he is in elementary school over anything 💩.

Love your video, very helpful. To avoid brush strokes you can use a glue spreader instead, they are usually in the kid’s craft section really cheap. I’ve just been making some bottle caps with glossy accents and had a real struggle with the air bubbles but it gives a lovely finish to things. xx

Thanks! This was really helpful! ✨

Instead of poking a needle into the end take the top off and stick the needle into it from the other side and pull it out. If it's a glue than it probably acts like a glue and you're just poking the goop up enough for some more goop to come thru but then you suck what's been dried back down into the tip which is why you spend so much time cleaning it out. So instead use a crochet hook, a small one preferably, and pull out what's drying from the inside of the nozzle instead of trying to poke it back down into the bottle from the outside. Wipe it on a tissue and dispose of it & then you should have a hassle free crafting day from then on out. Well, in so far as that one product is concerned anyway. You'll likely have to do it every time u use it but it doesn't take long if u start that way. Just make sure you pull it out in 1 piece. Usually it dries into the grooves where the cap screws on, too. Just where the air has hit that surface. Depending on the size of the bottle (because other things do this, too. Some inks and glitter products 🤷) for things of similar consistencies I like to take a wet paper towel or cling wrap and stick it down over the product when I'm done for the day & then put the cap back on just enough so that you screw your cling wrap up in the cap to hold it in place so u can pull it out easy the next time u use it. This will allow for a truly air tight seal and save u a huge headache in the long run. That needle trick only works when products like that are brand new.

I’d love to see the same comparison done on beaded jewellery to see what stiffens it up without making it brittle and without any chance of it yellowing! But I enjoyed this, it showed me the products I’m thinking of and that have been suggested!😊

Thx for this awesome video. I keep all three of the latter on hand. My favorite is Triple Thick by DecoArt Americana. I use little eyeshadow makeup sponges to apply or makeup sponge wedges. Also less bubbles than the others. There is also hard to find Mod Podge Super Gloss-Brilliant. It's a one coat finish and the only MP I've seen that doesn't say water base. Got mine on Amazon.

Thank you , you really help me

Is glossy accent still ur favorite pick . I'm trying to figure out what I want to put on my shrink dink and resin is not an option. I was wondering if you seen any yellowing I'm going to be making keychains😊 thank you in advance for ur help 😊

Hi! A few reviews on Amazon mentioned that the Glossy Accents turned yellow on their project after it dried. Have you noticed this on any of your products? Do you still recommend this product?

Does the lid come of on the glossy accents? If so cant u use a paint brush as well?

Hello, thanks for posting this video. I bought a bottle of glossy accents a couple of weeks ago and was very disappointed. I have tried to use it in many ways but it cracks as soon as it's dry. I've tried applying it thinly as well as thick but they all come out crack. I know they do a glossy accents with crack effects I made sure to check mine a few times and it was a regular glossy accents. Does anyone have the same problem? Could you please advise if I am doing something wrong? Thanks in advance and have a beautiful day.

The mod podge doesn't came out sticky? I have seen some videos about that and also, Does anyone of those glazes get off with water or something?

Do you have any solutions to modge podge streaking?

can this be used in moulds to make things like they are made with resin

Thak you very much 🥰

Have you ever used Glossy Accents with a brush?