GM 14 bolt disk brake conversion from Ruff Stuff

Рет қаралды 20,404

Жыл бұрын

We do a drum to disk brake conversion on Jason's 1st Gen Jimmy truggy using a complete kit from Ruff Stuff.
Kit:
www.ruffstuffspecialties.com/...
Shop parts used on our projects on our Amazon store: www.amazon.com/Shop/UintaGarage

Пікірлер: 33

@johndishong5083 6 ай бұрын

I love watching guys in short sleeves and shorts welding. Bonus points for doing it in flip flops. :0) I'll be getting this kit. Thumbs up!

@UintaGarage 6 ай бұрын

Gotta get that welders tan somehow!

@froggymoto5766 Жыл бұрын

“I just showed to hit stuff” lol😂

@RuffstuffSpecialties Жыл бұрын

Such a great video, very informative and well explained! Thanks guys!

@Rocketbunie Жыл бұрын

Do y’all still offer the 14 bolt conversion? It won’t let me add to cart

@danbier5461 Жыл бұрын

Great video! Gonna watch it for bearing preload

@mjo326 Жыл бұрын

This is the best conversion video I've seen. Thank you for making this.

@UintaGarage Жыл бұрын

Thanks! Glad you liked it.

@wrightb55 Ай бұрын

It’s a good idea to put some oil on the wheel bearings. Gear oil doesn’t get out unless you tilt the axle house.

@UintaGarage Ай бұрын

Good suggestion, we’ll keep that in mind.

@t-roy3438 2 ай бұрын

Thanks

@jakepeterson8690 4 ай бұрын

stud part number: Papco: 560-461 GM (O.E.M.): 355815 Dorman: 610-194 or 610-194.1 Raybestos: 5741B

@victoroneill7924 Жыл бұрын

I've watched this video several times to see how you removed the 2 factory brackets on the emergency brake cable from the drum backing plate. It appears that they just magically disappeared 😊. I think I can get one of them off with a cutoff wheel but I don't know about the other one. I wish Ruffstuff would make an emergency cable for my truck ('80 Chevy K20) with the factory brackets removed and a bracket that I can weld on my differntial.

@UintaGarage Жыл бұрын

At 4:01 you can see the 2 bolt holes from the bolts that hold the cable bracket to the backing plate. We didn't film us removing them, but they were there. ;)

@victoroneill7924 Жыл бұрын

@@UintaGarage I saw that but I'd like to know how you removed the brackets (or bracket) without damaging the parking brake tube. Both the brackets on my truck are crimped onto the parking brake tube but the bracket on the outside of the backing plate is very thick metal. I'm doing this in my garage for fun. I discovered yesterday that the professionals that replaced my leaking pinion seal years ago cross threaded or over tightened a bunch of the 3/8" bolts that hold the differential cover on (it was leaking real bad). I'm replacing the leaking cover with one of Ruffstuff's 1/4" covers. I have a Helicoil Repair Kit ordered. This is by far the best video I've found of this brake conversion!

@ravenrivera1950 10 ай бұрын

Can you guys tell me what size heli coil was used to repair the stripped bolt hole on the hub? I have a stripped bolt and planning on doing disk brakes going to kill 2 birds 1 stone! Thank you guys for the video

@workingmansrestorations7071 9 ай бұрын

What was reasoning for the longer studs?

@alchampion340 9 ай бұрын

What length lug studs did you use?

@dual1315 7 ай бұрын

Has anyone used one of the newer 14bolts out of a 2000s truck with OEM disc brake setup? Any advice.... thank you

@UintaGarage 7 ай бұрын

We've seen it done, but don't have much information on it. I think the newer axles are wider though, so that might be an issue.

@kitwatson8475 Жыл бұрын

Did you leave the factory proportioning valve located below the radiator in place?

@UintaGarage 11 ай бұрын

We left the valve in place, but pulled the guts out of it. Hope that helps.

@user-tl4xi4vc9d Жыл бұрын

What's the size and length of the new wheel studs

@UintaGarage Жыл бұрын

The customer bought them ahead of time, so we don't have the exact size.

@Rogerson785 10 ай бұрын

How do you pull the guts out of the proportioning valve.

@UintaGarage 10 ай бұрын

On one side there is a nut you unscrew and pull out the internals. It basically falls out.

@NDB390 Жыл бұрын

Did you change prop valve or MC ?

@UintaGarage 11 ай бұрын

We pulled the guts out of the prop valve, but kept the same master cylinder.

@Brantithor Жыл бұрын

When you say the rotors came from a GM ¾t, does that mean they're 1.28" thick and 12.50" in diameter? A.k.a. JB6 or JB7 rotors?

@UintaGarage Жыл бұрын

Sorry but we didn’t measure the rotors and don’t recall. This is the kit from Ruff Stuff and the specs should be on their site. www.ruffstuffspecialties.com/R1877.html