Gm steering gearbox input shaft seal replace

No video

Gm steering gearbox input shaft seal replace

Рет қаралды 46,658

Alex the vato adapts

Күн бұрын

Gm chevy steering gear box input shaft seal replacement

Пікірлер: 29

@bobbydavies1408 4 жыл бұрын

Good job on the video, your right, there isnt hardly any info for this specific task, even in the old school chilton and haynes books, so thank you for covering it straight to the point with knolage and no bullshit, just good directions and tipps👍👍👍👍

@FuquarProductions 5 ай бұрын

Hey yo... This is the same setup as my one ton Dually, Thanks for posting! Reman gear box... $190 with a $50 core OR $9 seal kit...

@alexlowvato 5 ай бұрын

Yup thanks for watching

@joshuariehl6213 Ай бұрын

I am building an s10 and just put fluid in my pump and found out the input shaft is leaking. I'll be doing this fix this weekend. Thanks!

@alexlowvato Ай бұрын

Gland I could help💯

@michaelgee5917 6 ай бұрын

Thank you for making this mate, there’s so much info on other brands but this really helped me on my old K10. Cheers.

@alexlowvato 6 ай бұрын

You are very welcome. Thank you for watching.

@ralphcuellar6434 3 жыл бұрын

Ill be doing this on a 1975 k10 soon. Thanks for the kit info

@Fr33dom89 3 жыл бұрын

How do you adjust the preloade

@mibars 6 ай бұрын

How do you adjust it after assembling everything togerther? The only guide I found tells that it must be screwed in until input shaft rotates with a force of 6-10 in ft (0.7 - 1.1 Nm), but the gearbox must be dry, pitman shaft adjustment backed off, etc.

@alexlowvato 6 ай бұрын

I just reworked everything back the way it was didn’t mess with any of the adjustment or anything. I don’t think

@mibars 6 ай бұрын

@@alexlowvato Okay, so I guess I'll attempt it that way, on a truck, if something will be off I'll give it a twist in one or the other direction :)

@alexlowvato 6 ай бұрын

Yes sir it’s pretty self-explanatory. It’s just a worm gear inside. If you have some ears on that gearbox you might want to adjust the gearbox anyways by having somebody inside turn the wheel left to right left to right while you’re adjusting the screw with an Allen wrench in the center, you don’t want it too tight though

@peteevcyfus1540 Жыл бұрын

Finally no beating around the bush n to the 👉

@jacob14ish 2 жыл бұрын

Any one have any ideas to getting out the adjuster with the two holes drilled on the front of it? I have tried everything I have to get it off! Heat, pb blaster, hammer with a punch, pliers etc and it won’t budge.

@alexlowvato 2 жыл бұрын

Not sure if you have access to a welder you might be able to make a little spanner tool for it that’s what I have to do to get mine free

@zacharymikell1847 Жыл бұрын

Trying to figure out why I can’t get the cylinder to screw back in as far as it was before taking it out

@alexlowvato Жыл бұрын

I believe it’s like a worm gear

@briantruck2284 3 жыл бұрын

I just wanna replace the wheel gear box

@dannyal467 3 жыл бұрын

hey i did this last night n for some reason it still leaks from the same place i replace those three things but i leaks from the same place any tips...thanks

@alexlowvato 3 жыл бұрын

Did you tighten to the right pre load? Also was there any wear marks on the steering shaft where the seal rides? maybe a little Emory cloth sand. Also I have seen some seals dry up on the shelf. Keep us posted. And good luck!

@dannyal467 3 жыл бұрын

@@alexlowvatoi clean it well it look smooth n clean no damaged i came to auto parts and they say to take it out n put it back in and add some sealer so im gna tap it more and see how that turns thanks bro

@alexlowvato 3 жыл бұрын

Yes sir hopefully it all works out for you. You will get it done brotha💪🏽

@dannyal467 3 жыл бұрын

@@alexlowvato so i took the gear box out again today i tapped the seal more n it seem that it went further in this time and i added a sealer around it from the inside part im letting it dry over night n tomorrow ill put it back and see how that goes 👍🏻 (if it doesn’t work ima have to take it n get it fix )

@dannyal467 3 жыл бұрын

@@alexlowvato hey i fix the leak finally! i had pushed the gasket further n added sealer andf it leaks a lil from the meatsl polygon plate so i feel that if i tight it more itll fix the leak 👍🏻🇺🇸