Several people have commented saying I used the Torque Wrench wrong. They are applying rules without understanding the reasoning for the rule. The M16/M4 - 23&P Manual shows (With Pictures) the USGI Adapter being used inline with a Torque Wrench. Why is this when the experts claim it's wrong? It's because the torque values listed in the 23&P Manual (38-42 FT#) take that into account. When the USGI Adaptor is being used inline, the leverage it creates is part of the formula. The USGI Adaptors over the past 60 years have the same amount of distance between the torque wrench keyway and the centerline of the tools workpiece. I know because I own them all and have and tested them. Inline vs 90 degree value is less than 3 ft# for the USGI Adaptor and for this particular Tool and application. Notice how I set the wrench to the middle value (38-42 ft#)? My Torque Wrench was just calibrated and is accurate to -3%. That specific torque value was also important because in the past the castle nut was tightened with fixtures that didn't lock the receiver extension and lower into a solid fixture. Too much torque would cause the receiver extension to rip past it's keyway and cause clocking and damage to the tube. With better fixtures (as shown in this video) a higher torque value will not allow damage because the receiver extension and lower are in forced alignment.
@bidenisatraitor76339 ай бұрын
I don't give a damn what they say. I trust you before I trust them. Period!
@Doomer170189 ай бұрын
lol people love to point out what they think is an error because it makes them feel smart.
@ShawnD10279 ай бұрын
@@Doomer17018, for some folks, probably. For others, it's because stopping perpetuation of bad/damaging techniques is important (YES, I fully understand is NOT the case here).
@BlueCollarBachelor9 ай бұрын
They'd really hate when I stick a castle nut wrench on there and wack it with a hammer.
@NuYo-9 ай бұрын
G you don’t have to explain yourself to no one
@thatarguy9 ай бұрын
The green jig everyone is asking about is the TechCo AR15 Receiver Extension Tube Jig. Y'all are welcome.
@MyCCW9 ай бұрын
My day is made...as enginerdial as many of us are, I'm surprised no one has come out with a staking jig up until now. Yes, I know it's a simple process with a punch, but I know it's taken me a few castle nuts to get good stakes "most" of the time. Most of us aren't staking castle nuts day in and day out so this jig looks like a great way to get good stakes. Kudos to your student for creating something that truly solves a problem.
@chipsramek38689 ай бұрын
@MyCCW ... I think it's Groovy that You still use Kudos.
@Wonderkidd8639 ай бұрын
The alignment jig is the best part. Perhaps the developer will make one that aligns to milspec castle nuts at some point. Excellent product for those planning several new builds, but tough for existing. I actually prefer the non auto punch staking tool as well for whatever reason…so a single jig would be an excellent add to the bench 👍🇺🇸
@michiganmafiamx554312 күн бұрын
Thanks Chad, another great video. A couple firsts for me here, contemplating a drunk woodpecker’s actions was not one I expected to hear, but it was a well executed analogy. Kudos to drunk woodpeckers and great analogies..
@johngalt1769 ай бұрын
I believe you can adjust the tension spring on the center punch to increase the striking force. Righty tighty. Lefty loosey. At least you can on my starrett auto punch.
@printingwithpeek48979 ай бұрын
The Starrett auto punch is an amazing punch. Definitely the best one out there, especially with the materials they're using.
@goinhot91339 ай бұрын
@@printingwithpeek4897I have the starrett auto punch, never noticed that feature
@printingwithpeek48979 ай бұрын
@@goinhot9133 Hey, it's never too late to learn@
@clint22119 ай бұрын
Awhile back I purchased a complete lower from Palmetto State Armory. It was suppose to be a non blem item but it turned out to be a blem item and a bad blem at that. It also turned out that the staking of the castle nut was horrible. With this armorer's kit I feel comfortable fixing the issue myself. Chad, I can't thank you enough for showcasing this unique item. Kudos to the individual for offering this and making life as a builder that much easier.
@birdsoup7779 ай бұрын
Awesome Channel. Appercaite your talent and your commitment to learn it
@printingwithpeek48979 ай бұрын
This is exactly the type of thing that makes homebuilds better. Sure, most people won't have machining capabilities but if you get parts from reputable manufacturers and you gauge them, you can have a rifle set up that meets and exceeds milspec. There is no reason, not to do this. I will definitely be adding this tool to my line up.
@joelatkinson20809 ай бұрын
Just an idea for a future video. I'd love to see you do an evaluation of Anderson's RF85 treatment and how it compares to other friction reducing treatments and coatings. Love the channel and thanks for all the content you put out.
@Pyle819 ай бұрын
Sweet little kit, Something ill definitely be adding to my Armour's Bench tool box. Thanks for showcasing this unique tool.
@mrsillyname9 ай бұрын
Get this man to 100k!
@BreezyBeary4 ай бұрын
That tool is amazing and you are an exceptional armorer. Subscribed! I have assembled 20+ ARs and your attention to detail is top notch and I learned from you already! Thank you.
@TheWarriorSolution9 ай бұрын
What a cool design! Awesome idea and perfectly executed for home builders. Well done Echo Zulu.
@nickadkins77659 ай бұрын
Tango Uniform is the name of the company. Echo Zulu refers to the name of the kit.
@thelastlatchkeykid84669 ай бұрын
I can watch these videos all day.
@misterphuzz9 ай бұрын
I like little inventions like this. My only recommendation, for version two of their product, is to angle it just a little bit, just a wee little bit, so that it puts a little bit more focus on moving material in the direction of the notch. Other than that, I like the idea.
@frozennorth34269 ай бұрын
I like the variant on the Fallen logo. More firearms reference back to the skateboard world :) Always good to see.
@johnknouse88469 ай бұрын
Could have used that several years ago when I was butchering my staking job!! Great video as usual.
@silentstryker15908 ай бұрын
That's nice! Thank you for another upload.
@tdjohnsky2 ай бұрын
“Drunk woodpecker “ 😂
@107gamma3 ай бұрын
I got my tango staking set now. Thank you.
@justlookingaround7 ай бұрын
Looks like a great tool and definitely looks professional.
@steveninaz95769 ай бұрын
Just ordered one. Great item
@Radvous4 ай бұрын
I bought the same spring loaded punch on Amazon a few years back, works amazing as a staking tool.
@knewsome699 ай бұрын
Drunken woodpecker…so you HAVE seen my staking skills!😂
@dalesmth19 ай бұрын
In my twenty years of building Ars, I’ve never staked a castle nut. Nor had one come loose.
@SchooloftheAmericanRifle9 ай бұрын
Doing something wrong for 20 years isn't a good thing.
@JCunningham219 ай бұрын
How many Carbine classes has it made it through?
@dalesmth19 ай бұрын
@@JCunningham21 3,000 rounds and counting.
@mrshort23799 ай бұрын
Awesome castle nut staking kit, awesome design: However I dont want to come off like a troll, but I would have to iterate, that it is not worth the $85. price tag being asked, especially for a proprietary castle but and jig, and those of us that are not staking a daily multitude of castle nuts, you could most likely piece together that whole kit except the jig, for the price of the jig. Just saying
@NoWr2Run9 ай бұрын
AGREED.
@BrassAngels9 ай бұрын
Groovy little tool! Glad someone cam3 up with it cause I thoroughly enjoy tools that make my efforts easier & make my end result better. Cheers & Thank you! #SOTAR #SOLGW #ARJunkie
@TheGalliaComata9 ай бұрын
Nifty. I like that wrench head. At the very least nice fast way to make a couple centered marks. Thanks
@bamzilla.27 күн бұрын
Damn....just found this vid. Out of stock. I NEED! :D
@5shotsr6118 ай бұрын
Fantastic idea thanks for sharing!!
@gregphillips96709 ай бұрын
I recently purchased a non AR related item and included in the package was one of the castle nut stickers. Naturally I checked out their website. I haven't bought a kit yet but will in the near future.
@DickLickBiden-zy3nf9 ай бұрын
Lol without reading instructions. Many may not enjoy your sense of humor and even more likely don't even catch most of it. I for one appreciate and enjoy it.
@cjanquart9 ай бұрын
That's a great jig; my first build went well but using a Starett punch I wasn't able to get it perfect, but at least I didn't bubba-gonsmif it (like nsz85). This is perfect for alignment then following up as you did at an angle without the jig. Agreed; would most definitely like to see a version that would work with milspec castle nuts.
@kennyfinley8613Ай бұрын
Excellent tool and video. Only comment would be to use the wrench at 90 deg from the extension so you don't increase torque being applied from the extra length.
@lkazanov7 ай бұрын
Very cool, the requirement for a proprietary castle nut is a bit of a turn-off. It is basically a locating punch jig. But kudos to them. The use of the Geissele receiver extension holder makes this task very simple.
@Larrymoecurley9 ай бұрын
You must be a great teacher!!
@dangerdoberman9 ай бұрын
Whoa. That's really great.
@Toolness15 ай бұрын
Very cool. Some of mine are ugly but they hold. I did order one of the spring loaded ones you pull back and let go to use on my next one, that'll help me a lot. I'll use a push-down one like this for my starting divot and then switch to the other for some more oomph.
@Maine3079 ай бұрын
great tool!! BUT, lets also talk about that AWESOME greenish receiver holder!!! WOW !!! OMG!
@digitalshooter29059 ай бұрын
The only bad part of this jig in my opinion is it's a proprietary tool. Should've just designed it to work with milspec castle nuts. Then maybe he could've designed a different castle nut that works with it and sold that as well if he wanted to.
@mikedj4207 ай бұрын
That bottle of sriracha is a must have for every serious armorer.
@M14Shooter9 ай бұрын
Great solution!
@matthewbeaver50269 ай бұрын
I understand that they would like for us to purchase their castle nuts. Though for us poors it'd be nice if they would make a jig for a mil spec nut.
@doejohn86749 ай бұрын
Very cool tool!
@NateDizity14207 ай бұрын
Good video. Just picked up the starter kit on Brownells. Nut Wrench would've been nice to have but trying to keep costs down.
@steveninaz95769 ай бұрын
Thank you Sir
@philbaker2928 күн бұрын
Not gonna lie, I'm in the "non-staking" group. But this is a handy tool.
@samvittoria96929 ай бұрын
That is awesome.
@BAdventures8 ай бұрын
Good quick demo and review. Please review the Forward Controls CN5F Extended Castle Nut. More thread engagement and coverage. Is it stronger and any better than mil-spec?
@charlesgillette29259 ай бұрын
Great idea.
@markannadale75339 ай бұрын
Who makes the fixture that the lower and receiver extension was places in? That is very nice.
@Mr_Clean9 ай бұрын
Techco. Ncstar makes one, botach makes one and G$$$$$ makes one
@j_flo9 ай бұрын
Thanks for the reco. I saw your ratcheting castle but video and I’m rethinking that method. 🇺🇸🦅2A
@Shackleford_Rusty9 ай бұрын
Just what I’ve been looking for, just snagged one. Thanks Chad
@Sam-et3bv6 ай бұрын
Awesome. Very awesome.
@bfonfield15349 ай бұрын
We need a hug for our FCD castle nuts sir.
@akmarksman9 ай бұрын
That is a neat product. Not a bad price for the Armorer's kit.
@michaelfrangoudakis8233 ай бұрын
That’s a nice tool.
@ryanthomas23749 ай бұрын
buying... for sure
@boinger19889 ай бұрын
very slick!
@sraldiris9 ай бұрын
I need that!
@JamesBond-ut5iv9 ай бұрын
It's an interesting one. I've gotten good at staking but this would have helped during the learning process. I've got some ugly ones for sure.
@Auggie_939 ай бұрын
Didn't know you were based out of Maryland. Might have to give you folks a visit
@scott22286 ай бұрын
That wrench looks like it will give FCDs a run for its $. If I didn’t have it I’d pick this kit up for sure.
@William-Bill-Munny3 ай бұрын
LOL the Bob Ross of gunsmiths
@rux22133 ай бұрын
laughing at the "drunk woodpecker" comment!
@musician4458 ай бұрын
"Oh yeah look at that staking". haha I love it man, i was saying the same thing to myself. Thats one of those moments where my girlfriend would have turned to me and said "NNEEEEEERRRD". XD
@pkake13199 ай бұрын
My stakes work. But aren't pretty, I would have bought this as a matter of pride in my own work.
@bayoucity19 ай бұрын
"I don't want to cut into the instructions." *Proceeds to tear the instructions to confetti.
@davelogan774 ай бұрын
Sweet.
@Randy_849 ай бұрын
Red loctite 😂😂😂
@justlookingaround7 ай бұрын
And know we know, and knowing is half the battle, GI Joe.
@Akinius9 ай бұрын
Nice! I don’t currently have any builds planned, but I’m ordering one of these for my next project, whenever it is. Question, though… where do you get that aeroshell grease in that handy container with a brush built into the lid? I’m used to little tubs and having to use an external brush or something that dries out or gets lost between uses… Thanks!
@jamesbullock325927 күн бұрын
Very Kool
@AR-ud1dp9 ай бұрын
Hi, love your videos however why not just use the pws ratchet lock! It’s easy and awesome at the same time! Takes under a minute to install!
@SchooloftheAmericanRifle9 ай бұрын
Because I have a negative opinion of them.
@AR-ud1dp9 ай бұрын
@@SchooloftheAmericanRifleso I have learned a lot from your videos! More than I could once imagine that one day I’ll know so much about ar15’s. Please elaborate on what kinda problem or problems you are referring to?I have them in all my ar’s that I’ve built. 2 of them in particular have been run hard and somewhat abused. Never had a problem with them!
@V8SKULLS6 ай бұрын
Beautiful video, thanks for sharing, could you tell me you wonderful vise jig, the green one, that holds everything in line, I want to purchase one. Thank you very much
@DerWaidmann_9 ай бұрын
What is your opinion on the PWS ratcheting castle nut/endplate system?
@tonyc2239 ай бұрын
I have 3 on lowers. I like them,never came loose. Thousands of rounds.
@bidenisatraitor76339 ай бұрын
I like this method better..just an opinion...stick to basics
@printingwithpeek48979 ай бұрын
The end plate is not truly ratcheting and does shear if torqued the wrong way. If you want that style of system, the better option is the Fortis K2.
@Shootsmith9 ай бұрын
Love mine, switched over
@SchooloftheAmericanRifle9 ай бұрын
Seen many come loose, especially if they are reused. The tooth wears flat.
@ravenovatechnologies65549 ай бұрын
Very cool tool, very good tutorial. But i do have a question. Have you ever seen issues from a badly staked buffer extention tube? To me it seems like even single stake is more than enough to hold it for a lifetime of abuse. Maybe i have rose colored glasses on, but ive never had a single issue with a castle nut backing off. Perhaps im just staking properly...
@frozennorth34269 ай бұрын
The receiver extension tube doesn’t need to be staked, only the castle nut that generates axial pressure between it and the lower (via the endplate which acts as a spacer between the two). Castle nut staking is a plastic deformation of the endplate metal that fixes the endplate’s rotation relative to the castle nut. (and the endplate in turn already has its rotation mechanically fixed relative to the lower) The expectable forces that could rotate the castle nut relative to the endplate are at worst what we would colloquially call “jiggling”. That’s it. Literally all we’re trying to do is control jiggling. We’re just doing so on a machine that’s pretty good at jiggling things. The only function of staking is to offer a degree of mechanical obstruction to Jiggling Rotation that is: - greater than our arbitrary thread friction and/or adhesive can provide - less than would require irreversible welding So, staking merely introduces a mechanical barrier to rotation (forming a plasticly formed de facto lug) that a little jiggling won’t overcome even when adhesives and friction from axial thread pressure have failed to attest the jiggling. That is to say, as something that actually changes the Shape of (plasticly deforms) metal objects, castle nut staking doesn’t really have to accomplish much. Picture a glass mason jar with a notch in it that you can hammer a bit of the rim of the lid into. You can shake that jar as hard as you want forever, but you if you’ve hammered a bit of the lid’s edge into that notch, no matter what thread friction and adhesive you overcome with shaking, that lid is never gonna rotate relative to the glass, because it’s floating in between the sides of that notch. It offers rotational resistance, but not in a fight against any rotational force, only against jiggling. A minor torsional effort with a wrench can break a castle nut stake like it’s nothing, and that’s the way it should be, because it’s meant to be a small and reversible thing resisting far Smaller stresses. In fact that’s the reason we call so much attention to castle nut staking: because it accomplishes something so mechanically Minor that most people don’t even imagine it’s worth doing.
@In-Midnight-Clad9 ай бұрын
As long as the staking has moved enough material into the staking notch, it'll serve its purpose. Functionally, it doesn't matter how ugly it is, but Chad's a professional and cares about how his work looks. Understandably so.
@bmeng71529 ай бұрын
Whats the name of the green block you used to keep the receiver aligned with the buffer tube??
@Larrymoecurley9 ай бұрын
Where did you get the lower receiver vise ? Well done video.
@Whizzo3336 ай бұрын
Actually the starter kit does have tool inside, small punch....🇺🇸✊
@ForceRecon1126 ай бұрын
If you're applying appropriate torque, something like vibratite is not necessary, correct?
@boriquais9 ай бұрын
SOTAR have you staked griffin endplates? I destroyed 2 good quality punches and didn’t even scratch the finish.
@JadedGLORY26899 ай бұрын
Haha "We'll do it live. We'll do it F***ING LIVE!!!!!
@nickadams29519 ай бұрын
Does this work with a standard castle nut
@drewbaglin16325 ай бұрын
Is it possible to send a lower to you for buffer tube adjustment and restaking?
@lucasdunajski80189 ай бұрын
Where did you get that reciever extension block for the vise?
@TROY-MCCLURE-1991Ай бұрын
What digital torque wrench were you using?
@DB2A79 ай бұрын
Fancy
@mrpibb77819 ай бұрын
My two builds i "cheated" and used PWS ratcheting castlenuts. No staking required. This thing may warrant a looksie though
@Cameron-bk5gk2 ай бұрын
Shouldn't the castle nut wrench be 90 degrees from the torque wrench handle to achieve proper torque value? I always thought having it at any other angle would cause an incorrect reading.
@TROY-MCCLURE-1991Ай бұрын
What digital torque wrench do you use?
@DickLickBiden-zy3nf9 ай бұрын
Wow I really like that vise tool for the lower. Very nice!
@vinceburris25389 ай бұрын
Could have used one of those a while back.
@fireboyrasmussen19769 ай бұрын
Never staked. Would like this kit. So what happens when you want to remove it? Does the end plate And the Castle nut just get ruined? Is it a pain to get off?
@fireboyrasmussen19769 ай бұрын
I watched your video removing one. I’m down with this kit.😊
@michaelfrangoudakis8233 ай бұрын
Will this tool work with the FCD castle nut?
@Radvous4 ай бұрын
Aren't crows feet technically supposed to be 90 degrees perpendicular? I know it really doesn't matter with such a short crows foot here, or if there's just a few more ft lbs on the castle nut on an AR.
@DET_C0RD9 ай бұрын
What if I didn’t grease the threads before I put my nude buffer tube in?
@Whizzo3336 ай бұрын
Probably be dead soon......
@allens95738 ай бұрын
The forever staking
@catx62629 ай бұрын
Hmm, someone should make a 3D-printable version of this tool