Tertemiz çalışma , gereksiz konuşmalar , bilgiler , müzik yok. İş bitimi parçaların ölçülerine kadar detaylı bilgiler. KZfaq'daki en sevdiğim kanal burası. Ellerinize sağlık .

Вот что значит золотые руки! 👍👍👍

👍 можно еще сбоку нанести разметку, чтоб оперативно делать толщину для заготовки

Fantastic idea. Definitely added this video to my "make this" woodworking playlist. One suggestion. Since you will need to take the shield off on a regular basis to clean and replace the sandpaper, and since a wood screw can only be removed and installed just so many times before it will no longer hold, I suggest that you use threaded metal inserts in the vertical supports that a machine screw can screw into rather than directly screwing through the shield and into the wood of the support. Then a machine screw with a washer will go through the shield and screw into the insert to hold the shield in place. Since the machine screw is going into the metal threads of the insert rather than directly into the wood, you can take the shield off as many times as you need to clean/replace the sandpaper. The same type of inserts could be used to mount the three vertical blocks in place. This would allow the entire sander to be taken apart and reassembled if needed without compromising the strength and rigidity of the joint between the base and the vertical supports. And a second suggestion. To make the shield stronger and hold its shape, you could take a very thin flexible piece of veneer and use just enough double sided tape to hold it in place on the vertical supports. Then brush the outer surface of the veneer and the ends of the strips in the underside of the shield with wood glue and wrap the shield over the veneer and screw it down. When the glue dries you will have a solid face on both the inner and outer surface of the shield, which will be much stronger than with just the very thin layer on the outer surface. The mounting screws on the supports will help clamp the outer shield to the layer of veneer, but there would be no clamping force in the middle. However, if you made one or two additional vertical supports with the same shape as the two that support the drum and temporarily mount them to the base without the drum in place, that would give you places in the middle where some clamping force can be applied.

Simple, efficient, functional! Congratulations on the amazing work! Greetings from São Paulo capital Brazil. 👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏

Without doubt best/easiest/cheapest to make DIY drum sander, I'm making a flat top mandolin and this is just right for my project. Thank you for no nonsense video

NO filler! - NO selling! - NO entertainment! --- STRAIGHT forward to the point! -- GREAT one √√√

Беларусь смотрит первая!!!

This is 2 things! The best tutorial I have seen on KZfaq And A perfect inexpensive and simple option instead of a $300 planer. Thank you! It’s perfect for what I need!

Отличное видео ,нужный колибровочный станок! Браво!!!

Хорошее приспособление. Буду делать, спасибо за размеры деталей.

Üstadım Elinize emeğinize sağlık, Türkiye'de böyle çalışmalar yapan birinin olmasından çok memnunum. İşiniz gücünüz rast gelsin...

Благодарю за труд и за то что делитесь так подробно

This is how a DIY video should've done. Detailed and all necessary pointers were shown. Kudos sir! Thank u for bringing a newbie like me better ideas!

Bu videolar insani hipnotize ediyor. Saatlerce seyrediyorum. Beynim dinleniyor.

Excepcional ideia e facilita muito a vida de quem gosta de marcenaria caseira!!! Parabéns!

Что автор не сделает,то становится шедевром. Браво.

I just finished mine! However, I did make changes. I went with a 5/8 shaft (found some cheap ones on Amazon), the power source is an old angle grinder which spins at 4500 rpm so I added V-belt pulleys to reduce the drum rpm to about 2000 and made the drum width about 20 inches, 3.5 diameter. I still need to add the cover for hooking it up the shop vacuum and another cover to protect myself from the pullies. I've got about 20 end grain boards to the point of needing a surface sander, didn't take long to run two of them "testing" the sander. Big thanks to you Gokmen! I might post a video of mine, I'll be sure and mention your design being the inspiration.

Очень умно и продуманно сделанно ! Такая работа заслуживакт похвалы , а Лайк темболее !

The true pragmatic craftsmanship! Bravo!

Gökmen = Bilgin Dayı 👍

Very nice project but unfortunately impractical because incomplete: - there's no easy height adjustment (missing is a single knob to allow adjusting the height of the tray) - there's no easy way to replace the sand paper or drum. Other than that, great. Also (a nitpick) a power drill is not meant to run for long times such as is required with a drum sander, consequently it won't last long and hence a dedicated motor makes most sense for this project.

Excellent video, straight forward, easy to follow and looks to work well! Thanks from London England 👍💪😎🏴󠁧󠁢󠁥󠁮󠁧󠁿🙏

Merci beaucoup mon ami pour cette vidéo c’est un plaisir de te retrouver après cette pause et d’apprendre de tes vidéos 👍🙏👍

Excelente trabalho, muito criativo. Parabéns pela idéia!

Cool build. Thanks for sharing the dimensions

I am often dubious about DIY shop power tools but every part made and assembled as demonstrated in this video gives me confidence that this sander can provide a quality outcome in thickness variation across the work piece. Great job. You may want to add some operational information about how much can be removed in a single pass and how to set the removal depth accurately and how to set the drills RPM for optimal sandpaper and drill life. Thanks

Brilliantly simple design, thank you for sharing

One of the best projects I have ever seen,perfect job

Gerçekten çok güzel bir eser sen bir şahısın eline emeğine sağlık

просто красавец,умница.

Smoothing the drum with a reversed drum sander nice!

You have a very smart plan about this ,I am gonna follow your staps.Thanks.

Excelente trabalho . meus parabéns aqui do Brasil.

Просто и доступно! Мне очень нравится! Лайк и подписка.

Großartige Arbeit - sehr effizient - intelligente Lösung - das fertige Teile könnte man kaufen!

Отлично! Возьму на заметку.

I have been watching your Videos for several Years and you always are got better,keep it up Greetings from Germany

Fantastic!!! Of all the homemade thickness sanders I've seen videos for, this is the simplest, yet best working one going. The only thing that could make it better is the addition of some sort of "micrometer" height adjustment and a dial indicator to verify the change in height for real precise thickness sanding. Well done! This is the perfect rig for wood worker hobbyists and model builders...

Mükemmel. Elinize sağlık. Paylaşım için teşekkürler...

WOW! So simple and effective. Thumbs UP!!

Thank you very much. Especially for the last 30 seconds!)

Great video, thank you for taking the time and effort to show others how to build tools with tools.

Great work, effective and simple - when you know how. Thank you

What an impressively simple and great design! 👍🏻

Another great job, both the tool and the excellent presentation (though I'm surprised you did not make the rods and metal brackets from wood).

Beautiful design that emphasizes form over function. An epitome of minimalist elegance.

Heavily Matthias influenced. Nice job.

I can't wait to make this, as I very much need such a device. Thank you so very, very much!

Simple- to the point👍🏻

thank you for the idea🙏 il start using your skills again🙏 God bless you 🙏

Improving improving improving, love it. The dust shroud was shrewd way to eliminate work and material. Some years ago Shopnotes magazine offered a disk sander for us which used the shroud cover idea. very similar to yours. I imagine it could still be found. Thank you Gokmen. OK I subd.

You are an excellent Craftsman !!! Congratulations

very zen to watch this. Mesmerized

Congratulations! Beautiful project!

ABSOLUTELY MARVELOUS WORK!!! 👋👋👋

Отлично!!!Просто и надежно!

Severek, titizlikle yapılan iş, Dünya da ses getirir. Selamlar Brüksel'den, Necmeddin PEÇEN

Brilliant craftsman! Thanks for a video that's pure quality and WITHOUT nonsense. Do you think this simplistic design would work on something larger -- such as a 500mm bed?

Great practical build

You have a great head and hands! Thanks for your videos!

Excellent work! I have seen many on KZfaq but I will make mine like this one. Thank you for the measurements. Blessings.

Really great. Thank you for sharing this.

Lindo trabalho,amei.

Спасибо мастер, Красиво, !!

Usta ellerine sağlık. Yine güzel bir çalışma olmuş

A very clever design. Well done.

Always amazed me with the build. Good job man

Now that's an idea,thank you for sharing.

Nice work--both the sander and the video.

Excellent video! My bueno! I will be building this as soon as I get back home in my shop. Thanks y gracias

Çok basit ama kullanışlı oldu. Ellerine sağlık ustam. Videolarınızı daha sık görmek isterim. Özletiyorsunuz

Very nicely done! Great explanation, excellent workmanship! Shukran!

Great work. I would modify so that it would be easy to change sand paper. Maybe a dedicated motor as well. With some threaded rods you could adjust thickness easier. Thanks for the idea of the system.

Very nice! I liked your accurate work!

SUPER cool actually..

Fantastic Idea!!!! Superb!!!

Meus parabéns grande ideia você e muito zelo

Another great project, friend. My compliments on the great skills you possess. Thanks for sharing

Harika bir çalışma tebrikler elinize emeğinize sağlık cok çok süper çok beğendim

marangozlukla mucitliği birleştiren adam, ellerine sağlık

Beautiful work.....

Wow superbe idée, merci mon copain vraiment génial.👌👍

Beau travail ,et belle patience ..good

Absolutely Brilliant 👍

Awesome idea.

Понравилось, просто и эффективно. Единственное, что посоветую, смотрите на скорости 1.75.

Bravo majstore! 👍

Well, that’s simply pretty damn cool. Good job on both project and video.

Mükemmel bir çalışma, ellerine sağlık, paylaşım için teşekkürler 🙂

You really are the master

Легко повторить. Полезно использовать. Всех благ.

Excellente vidéo et bravo pour la qualité du travail 👍👏

Absolutely awesome

Beautiful, splendid!!! 👏👏👏 😊👍

Simple ,efficace ,super . Très beau Tito

Good craftsmanship！

particularly liked the dust cover

Excellent video and process. Thank you for sharing. I'll start building my sander soon. Thanks for the inspiration and plans...👍

Well done! Brilliantly made, & demonstrated. My question is: How do you know the thickness to set if you cannot easily see the drum?? Also, how can you set/adjust the thickness accurately??