Graz Makes: A Knife Bevel Grinding Jig!
Рет қаралды 124,175
Күн бұрынThe Graz-Grinder 5000 blueprints! (they are actually black and white):
bit.ly/grazblueprints
In this video, I make a knife grinding jig!
its a really solid, and inexpensive jig you can make for under 30 bucks!
hope you like the build and dont forget to leave a comment down below!
If you like these videos, support me over on my Patreon page!
/ grazmakes
here is the links to all the stuff I used in this build!
3/8 Inch Aluminum Plate:
amzn.to/2HCO6WD
Heim Joint:
amzn.to/2sV1Si0
Machine screws:
amzn.to/2HFMpHU
1/4 inch Wingnut:
amzn.to/2LFaiSn
Threaded Rod:
amzn.to/2kZyNhP
Corner Braces:
amzn.to/2JJu2a9
Utility Hinges:
amzn.to/2JtMLr2
aluminum flat bar:
low.es/2JyFiTt
My sweet and inexpensive bluetooth headphones:
amzn.to/2oDesRS
Please Like and Subscribe for future videos!
Don't forget to press the little bell notification so you'll know when new videos are released!
Twitter: / grazmakes
Instagram: / grazmakes
Thanks to Charlie Fogel of Plop Culture Prints for the fantastic logo.
/ plopculturep. .
/ charliefogel
Music:
"Full Tilt Slam"
Chapman Brothers Garage
from the album "Third Gear"
Check them out on itunes here:
apple.co/2jnHjnZ
If you're digging these videos, please feel free to share them with friends AND enemies!
#grazmakes
@papalilburn 5 жыл бұрын
Please drop the attempts at comedy, I want information, if I wanted comedy I'd watch a real comedian.
@GrazMakes 5 жыл бұрын
Dang! that was a big burn, lilburn. I'm very sorry you had to endure my bad jokes, I don't know what I was thinking. please accept my apology and thanks for watching! *fart noise*
@joshhammond231 5 жыл бұрын
Your a d bag tinyburn
@coiffeurnick2358 5 жыл бұрын
If you wanted boring DIY info go read a black & white paperback manual. You clicked @grazmakes video therefor you entered his house, therefor you dont make rules in someone elses house. Good Day Mate.
@jamieofalltrades536 4 жыл бұрын
Great thing about KZfaq is that you don't have to watch the video if it irritates you that much ;)
@JoseGabriel-dd2up 4 жыл бұрын
Man, this is KZfaq brother... You have so many other videos to watch... No one is keeping you in this channel
@charlieb2689 5 жыл бұрын
Made my jog today based the design in your video. Freaking awesome! Works like a charm.
@robertgolden1080 2 жыл бұрын
Awesome jig. Excellent video.
@MrBAMAREDNECK 4 жыл бұрын
Wow, finally a homemade one I like. I was fixing to build one from a hinge but this one is so much better!!!!
@007Jaredboy 3 жыл бұрын
Great jig and your sense of humor is great haha
@Maker238DeLoach 4 жыл бұрын
This is definitely going in the shop
@brentbogy9894 5 жыл бұрын
Awesome video.. Love the humor injected. Appreciate your time and effort.
@Mbonner73 3 жыл бұрын
Perfect, I'm gonna make one this weekend, thanks for posting this
@NagelHausForge 5 жыл бұрын
I've been looking at making a bevel jig for a while now and this is by far my favorite build. Thanks for making this video! Once I get one whipped up and in use I'll send ya a thank you blade!
@GrazMakes 5 жыл бұрын
awesome! i hope it helped!!! well if you send me a blade, I'll have to send you one back!
@jamesbarnhill8730 6 ай бұрын
Man I need one of these so bad. Great video!!
@timberg7377 5 жыл бұрын
Very cool idea
@shaun4787 5 жыл бұрын
I like this version of the jig without welding. Nice and simple design.
@GrazMakes 5 жыл бұрын
thanks man! i tried to make a super simple jig that anyone could make. glad you dig it! thanks for watching!
@mikegunnellsministriesinc5384 5 жыл бұрын
Very Well done and I want to say Thank You for the blueprint and May God Bless you and your family Greatly
@GrazMakes 5 жыл бұрын
Mike Gunnells Ministries Inc thanks! I’m glad you liked it!
@sta39cee Жыл бұрын
Definitely the best knife grinding jig I've seen on KZfaq. Also a simple make and very well narrated by you. This will be my next build. Thanks for the info and the laughs.
@jonwills4670 6 жыл бұрын
This was one of your best videos! Extremely funny and informative!
@GrazMakes 6 жыл бұрын
Thanks man!!! Much appreciated!!!❤️❤️
@WillPatagonia 3 жыл бұрын
Thank you for uploading a new video! I hope soon you can fix the previous video so we can see how you built the other jig!
@donquixote1138 5 жыл бұрын
The best jig found
@GrazMakes 5 жыл бұрын
thanks!
@damasydia 5 жыл бұрын
Awesome video very informative plus I appreciate the editing and work you put into it...
@GrazMakes 5 жыл бұрын
Airborne Mike thank you brother!!!
@derekforestier1708 6 жыл бұрын
Nice job and love the way that turned out. I will be copying it!!!
@GrazMakes 6 жыл бұрын
Thanks! And if you will be copying, I will be suing!
@danthemakerman 6 жыл бұрын
Great project and entertaining video! Well done!
@FredMcIntyre 6 жыл бұрын
Nice work! 👍👊
@str8trpn892 5 жыл бұрын
Loved this video, I would love one of those bevel jigs!
@jamesweaver2054 4 жыл бұрын
Awesome vid man. Lighthearted, clean, and informative. Really digging the parts list and an the easy to follow tutorial. Subscribed!
@GrazMakes 4 жыл бұрын
Thanks man!!! Glad you dug the video! Thanks for watching! Exclamation marks!
@stefanpetrescu4384 5 жыл бұрын
I like this kind of funny editing
@hippoandbearmakes3416 6 жыл бұрын
Love the video! Great work!
@GrazMakes 6 жыл бұрын
Thank you!!
@veronicastewart1959 5 жыл бұрын
Well I just found your video , guess better late than never I always say ! LoL I'm wanting to learn how to make knifes so hopefully I'll be able to learn , differently want to make this jig ! Thanks for sharing !
@HarlieJ 5 жыл бұрын
Just started building my jig from your plans last night - did not know you could cut plate aluminum with a table saw - how cool!!
@GrazMakes 5 жыл бұрын
HarlieJ nice! Yup! Check out other videos of people doing it too. Just be careful cutting it!
@tboynt2013 5 жыл бұрын
Thanks for the video! I also like that you have some humor. Lets all just have some fun and relax.
@GrazMakes 5 жыл бұрын
no, only serious videos from here on out! that guy with the beard isnt funny! just kidding, thanks for the love and support!!!!
@LetsPrepTogether 6 жыл бұрын
Nice one mate! I'll give that a go
@thomasthomas5963 4 жыл бұрын
I used self threading screws which worked great
@arcturusbbqsausagemaking2435 5 жыл бұрын
Great job...Thanks bro
@GrazMakes 5 жыл бұрын
glad you liked the video! thanks for your support!
@cantonripfist462 5 жыл бұрын
After about a 30 minutes to an hour of searching for a good design for a jig, I found this one, and it is by far the best I've seen. I can pick most of the stuff for it locally; I'm just having trouble finding the Heim Joint. I think what's cool about this is the functionality and how nice it looks! The quality of the videos is fantastic too! Good work, sir!
@GrazMakes 5 жыл бұрын
Canton RipFist thank you for the nice comment!!! Glad you like the design!!! Check out the amazon links in the description, that might help you find the rest of the parts you need!
@cantonripfist462 5 жыл бұрын
@@GrazMakes I will! This is honestly the first video of yours I have seen, and I'm glad I did. Definitely coming back for more!
@minimotoadventures867 4 жыл бұрын
Great job I am new to knife making and would love to build o.e of these soon
@IdealGrain 6 жыл бұрын
Great work Graz! And thanks Frank Oz for remembering to give Jake Blues his hat back.
@GrazMakes 6 жыл бұрын
Ahah thanks dude!! Anytime I can use a blues brothers reference in a video, I will. I guess you can say, I'm on a mission from gahd :-)
@jampeyt 5 жыл бұрын
So very well done ! I really need one so please...
@GrazMakes 5 жыл бұрын
thank you!
@SXT15 6 жыл бұрын
Thanks for this video still trying to decide how I want to make my grinding jig and the fact that there is no welding is always a plus.
@GrazMakes 6 жыл бұрын
You're welcome! I wanted to make the best jig with the fewest amount of tools so almost anyone could make one.
@maconSTUFF 5 жыл бұрын
I always love finding great Beards on KZfaq... LOL... I am also going to have to make one of these soon... great content man, I see this channel growing quickly... Rock on!
@GrazMakes 5 жыл бұрын
thank you from one beard to another!! lemme know how it comes out!
@mickeygilbertson7386 4 жыл бұрын
I want to thank you my friend, I will make this jig and I don't mind the humor at all.
@pikeevans8559 3 жыл бұрын
Could I make a suggestion? On the aluminum bar that the knife rests on. I think it would be great if there was a way to adjust the height from the top of the jig so you could even grind a narrow knife blade, and perhaps even scissors. Some kind of slots in that plate where it could ne slid up and down, and then tightened in place. Some kind of threaded stud welded or fastened in place on the narrow knife rest that insert into those slots, and a wing nut on the back to tighten it up once you have it in place.
@JeffLambville 6 жыл бұрын
I don't need a knife grinding jig, but I sure learned some cool techniques when working with aluminum. I love your videos!
@GrazMakes 6 жыл бұрын
good to hear! glad you like the videos!
@toma1460 5 жыл бұрын
Says the guy watching a knife bevel jig how to video haha
@KnightsArmory 5 жыл бұрын
Dude this was the best video I have seen one making one of those 😂😂😂😂😂😂LMAO!!
@GrazMakes 5 жыл бұрын
thanks man! glad you liked it!
@billyhubbard9493 5 жыл бұрын
Need that jig
@UDoIt2 6 жыл бұрын
Awesome - watching you now in Jackman's insta live.
@GrazMakes 6 жыл бұрын
I have a face for radio. Thanks for watching :-)
@augielimon7029 5 жыл бұрын
I absolutely I absolutely loved your video keep up the work. And the comedy parts are just fine with me I take it you grew up with Reading Rainbow. I did too have a good day
@GrazMakes 5 жыл бұрын
lol thank you!! but dont't take my word for it ;-) thanks for watching!
@TheGrantAlexander 4 жыл бұрын
Great little jig, but more importantly thanks for trying to present it in a fun way 👍
@GrazMakes 4 жыл бұрын
Thanks man!! I try to keep it fun for everyone watching! Glad you dig it!!
@TheGrantAlexander 4 жыл бұрын
@@GrazMakes i came over from the ask cast, so i knew what to expect!
@GrazMakes 4 жыл бұрын
The Grant Alexander ha I’m sorry! ;-)
@TheGrantAlexander 4 жыл бұрын
@@GrazMakes no worries, better to set expectations low 🤣
@marcseki3012 5 жыл бұрын
I wish I saw this when you first posted it. I’m trying to make a jig since I can’t seem to get my bevel right. I already screwed up 3 knives.
@GrazMakes 5 жыл бұрын
Marc Seki me too! Hopefully this helps! I’ve screwed up waaaay more than 3 blades. You learn a lot more from your screw ups than your successes. Keep at it!
@exhempknight 6 жыл бұрын
Quick tip on the hole tapping... Get some kind of lube in there. There's aluminum-specific tapping fluid, but even a light 3-in-1 type of oil will do. Makes the process much smoother, and less likely to break a tap. Also, in addition to the drill press clamps and/or vise another commenter suggested, a really good safety practice is removing jewelry (noticed you wearing your ring and watch). I've seen pictures of what can happen when something like that gets caught in a machine. Even small machines can do some real damage.
@GrazMakes 6 жыл бұрын
Now ya tell me!! Just kidding! I will check it out! Thanks for the info!!
@alanscannell 6 жыл бұрын
Ha ha that was an awesome video Graz! Great jig too. I don't do much with knives but if your giving that beer away...... 😂
@GrazMakes 6 жыл бұрын
ha, if you're ever in the boston area, Im always down for a beer!
@alanscannell 6 жыл бұрын
Graz Makes might just take you up on that next to.e I'm over 👍
@GrazMakes 6 жыл бұрын
Just lemme know!!!
@ronnewton606 5 жыл бұрын
like your vid a lot.. ive made my own bevel tool but like yours enough to make one like yours...and.. forget the remarks about your funnies.. there is always gonna be a aXXXX out there
@GrazMakes 5 жыл бұрын
thank you ron! its ok, I dont mind people chiming in with their opinions, they're just wrong ;-)
@blwngt1598 5 жыл бұрын
Why not cut a couple channels for the "blade rest" bolts to ride in to make the rest height adjustable? It would also help when make folder blades as well. *side note* Using something like Tap Magic can be beneficial when, get this..., tapping holes. (I know, who would have thought, right?) Sure is a nice looking jig though, that's for sure!
@shewitghidey6908 4 жыл бұрын
I like your hummer...hahah cool so that the last 2K is mine
@ManCrafting 6 жыл бұрын
Would there be any benefit to adding some inset magnets to hold the knife against the jig? I don't have one of those fancy grinders yet, so I don't really know. Just curious.
@GrazMakes 6 жыл бұрын
I totally forgot to show me using the thing in the video. I just use a cheap harbor freight clamp to hold down the blade to the jig. It doubles as a handle to grab on to that won't get too hot when grinding.
@ManCrafting 6 жыл бұрын
Hmmm. Maybe a second video.
@GrazMakes 6 жыл бұрын
You can see me using it with a clamp in the previous Mac the knife video!
@sumgai7 5 жыл бұрын
Yes and no, mostly no - and I speak from (related) experience. Briefly: magnets strong enough to hold the knife to the jig, against the downward forces of the belt, ALSO will want to hold the knife through the belt to the steel of the platen -behind- the belt. Also, the magnets you'd need are quite large surface area and tricky to inset in that thin aluminum - you'd need to use like a 1-5/8" Forstner bit - and need to be screwed in (or epoxied) to keep them from just pulling out by the steel. This is a pretty tricky operation. (There are other ways to do it but other disadvantages there too.) So, you COULD - but short answer (a) it's not easy and (b) not worth it.
@MrDirtysteve75 5 жыл бұрын
ManCraftingTM you could, but all the metal shavings would stick to it as you grind.
@elmcityvintage 6 жыл бұрын
Love the American movie clip.👍
@GrazMakes 6 жыл бұрын
i think it may be my favorite movie of all time. it gets better every damn time I watch it. #mikeshank
@elmcityvintage 6 жыл бұрын
Graz Makes good taste my friend
@GrazMakes 6 жыл бұрын
"It's gotta good taste." -uncle bill
@theplasticdesert2408 5 жыл бұрын
Bonus points for Chevy Chase caddyshack SFX and wearing a Seiko sea urchin.
@GrazMakes 5 жыл бұрын
thanks! its the perfect sound for a transition! also, bonus points for you for spotting my watch! thanks for watch-ing!
@heyimamaker 6 жыл бұрын
Skookum as frig!
@Simoooooooonn 6 жыл бұрын
you should have much more subs!
@GrazMakes 6 жыл бұрын
thanks! tell all your friends AND enemies!
@Simoooooooonn 6 жыл бұрын
Graz Makes i will 😂
@1pokras 5 жыл бұрын
How do you, Mr. Graz, fasten the blade to the jig? I'd like to see an easy way so the blade can be flipped without unscrewing etc? Thank you!!!
@GrazMakes 5 жыл бұрын
well mr. 1pokras, check out my video where i make a knife out of an old macintosh! in it, you can see how i use a cheap harbor freight clamp to fasten it to the jig!
@benjaminquiles8064 3 жыл бұрын
I see the blueprints but I do not see where to drill the hole locations/measurements are?
@evodefrane63 5 жыл бұрын
I need one please
@cmont59 5 жыл бұрын
Just watched this video which was first I’ve watched of yours subscribed right after informative yet comical awesome design would love to have one but how do you attach knife to it?
@GrazMakes 5 жыл бұрын
Thank you!!! I just use a cheap harbor freight clamp. Check out my “Mac the knife” video I think I use it on there.
@777tomwall 5 жыл бұрын
When I try to download the pdf it just returns to the same download page. Sorry to be a pain. I got all the material but I still can’t get the pdf downloaded. Thanks for you help.
@GrazMakes 5 жыл бұрын
try this link! filehost.net/20360c362696032d
@timberdish 6 жыл бұрын
Your vids are always short, sweet and very funny. Just like me. Except that I'm not that short. Or sweet. Or particularly funny. Anyway, keep up the good work! :-D
@jsksharp1 5 жыл бұрын
Great vid, I’m guessing I missed the bus on the bevel give away lol
@GrazMakes 5 жыл бұрын
thanks man! yea, the giveaway is over. if it's any consolation prize, you have the best screen name ever.
@jeffreygavlik3733 5 жыл бұрын
On your blueprint pdf, you dont have the dieminsions for the holes that you drilled. Can you send me the measurements for that please
@christianwilliams9663 5 жыл бұрын
How did you use a 1/4-28 heim joint with 1/4-20 all thread?
@Runningcheetah1 5 жыл бұрын
Christian Williams yup, ran into the same issue AFTER buying everything
@gmcg6326 5 жыл бұрын
Are the plans still available?
@GrazMakes 5 жыл бұрын
yup! check out the link for the plans!
@davebauerart 6 жыл бұрын
Awesome. Next contest can you give away couple of belt grinders to go with the jig?
@GrazMakes 6 жыл бұрын
Ha! I wish!! Have any contact to any grinder companies?
@davebauerart 6 жыл бұрын
Graz Makes no worries, I guess I'll be building a grinder.
@Mikey-qd8wo 5 жыл бұрын
Great idea and video. Like the guy below I am in dire need of one if you still got one. I also need a good grinding rest for my grizzly grinder if you have any ideas.
@GrazMakes 5 жыл бұрын
unfortunately i gave the two away. drop me a line at grazmakes@gmail.com if you want me to make you one for a small charge and also send me pics of your gizzly and maybe i can help!
@Mikey-qd8wo 5 жыл бұрын
Thanks for the reply. I will send you a picture this weekend of my setup.
@davidakamine3420 3 жыл бұрын
When making my jig, I realized, why make the jig, angle adjustable when the work table of my grinder is easily adjustable. Easier to make the jig at 90 degrees and adjust the table for bevel angle.
@BuzzingGoober 5 жыл бұрын
I've watched several knife bevel jig with adjustable angle videos and none seem to answer this question: how are you setting the angle? What device do you use?
@GrazMakes 5 жыл бұрын
you can get a cheap angle finder from harbor freight or even use a level app on your phone to find the right angle. hope that helps!
@geraldszaal7791 4 жыл бұрын
So you don’t mention the length of the treaded rod.
@icomba 5 жыл бұрын
I wanna know how it works?
@GrazMakes 5 жыл бұрын
check out the video where i made a knife out of a mac! i used for that!
@FBDerringer 4 жыл бұрын
Great vid! How can I get the jig?
@GrazMakes 4 жыл бұрын
i gave the two away but they are really easy to make! good luck and thanks for watching!
@c_conway 6 жыл бұрын
How the hell do I incorporate some Reading Rainbow, old-school Sesame Street and 70’s porn music w/aluminum? Ahhh! An adjustable jig! You’re the man Graz. Great video as always.
@GrazMakes 6 жыл бұрын
Ahahaha! I guess you can say both were early influences in my life ;-) thanks for the love man! Glad you dug the video!
@777tomwall 5 жыл бұрын
I can’t seem to find the pdf file you mentioned. I enjoyed the video. Thanks
@GrazMakes 5 жыл бұрын
just changed the link and it should be working now! sorry about that! glad you liked the video!
@jeverettrulz 5 жыл бұрын
having the same problem! Where in the comments section? And no Spies Like Us quotes, come now man!
@GrazMakes 5 жыл бұрын
ok, just made a new-NEW link to the PDF. its the first line under the video description. I double checked the link and it should be good to go!! thanks for watching and sorry about the link!
@jeverettrulz 5 жыл бұрын
@@GrazMakes Thank you!!! Already ordered the aluminum plate
@TimNewton0829 4 жыл бұрын
Um, I just ran across this video. Is it too late to enter to win the knife bevel jig??
@MarcelDiane 6 жыл бұрын
Funny stuff.
@GrazMakes 6 жыл бұрын
thanks marcel!
@JackmanWorks 5 жыл бұрын
Who has 2 thumbs and is embarrassingly late to watching this video 👍👍 On another note, I'm going to need you to email me that epic sound effect... 1:17
@JackmanWorks 5 жыл бұрын
Also, I just realized I stole that censor bit from you and hadn't even watched this video yet. I even impress myself sometimes.
@blatantmisconception 3 жыл бұрын
2021 checking in
@64t120r 3 жыл бұрын
I had to watch this twice. I was laughing too much the first time. I know I'm too late for the giveaway, but next time I make a grinding jig it may look suspiciously familiar to you. Not too suspicious, but a little suspicious.
@GrazMakes 3 жыл бұрын
64t120r ha! I’m glad you liked it!!! By all means make it and send me a pic!!!! Thanks for watching!!
@64t120r 3 жыл бұрын
@@GrazMakes I have a question about your jig. The hinges in yours seem very solid. My old jig has average hinges that have a bit of slop in them. What kind did you use?
@GrazMakes 3 жыл бұрын
I honestly can’t remember at this point. I know they were cheap hinges I bought from Home Depot it that helps!
@64t120r 3 жыл бұрын
@@GrazMakes I have depot hinges as well. I'm going to trim and tighten the knuckles. It should work. What could possibly go wrong?
@chloesdad2010 5 жыл бұрын
So did you have any issues screwing the 1/4 20 all thread into the 1/4 28 heim joint? The threading doesn’t match up so I’m wondering if there was issues.
@GrazMakes 5 жыл бұрын
I ended up recurring the treads but you could just get a compatible thread to the heim joint. Hope that helps and thanks for watching!
@chloesdad2010 5 жыл бұрын
Oh ok. That makes sense. Did you retap the heim joint or just recut the all thread? There doesn’t seem to be heim joints or really any other joints that are threaded in 1/4 20
@GrazMakes 5 жыл бұрын
its been a while but i think i retapped the all tread.
@chloesdad2010 5 жыл бұрын
Appreciate your replies. I’m making a version of this. Quite different but a similar adjusting method. Thank you much.
@GrazMakes 5 жыл бұрын
no problem! would love to see what you come up with!
@TheAffinitom 5 жыл бұрын
Did u give those jigs away yet? I'd love one to help me start out.
@GrazMakes 5 жыл бұрын
yeah sorry, give it a shot at making one! its pretty easy!! thanks for watching!
@ManCrafting 6 жыл бұрын
Graz, I'll save you the trouble of doing a drawing. Just send it to me. I'll do a test run when my grinder gets here in the next week.
@ManCrafting 6 жыл бұрын
I checked the mail. I still haven't seen it? I guess I'll just have to make one. ;-)
@zachdove4380 5 жыл бұрын
Anyway you can tell us the measurements of where you drilled? The pdf only shows the two pieces and the holes but not the actual measurements. Thanks!
@GrazMakes 5 жыл бұрын
hey zach, are you referring to the size of the tapped hole?
@zachdove4380 5 жыл бұрын
No I mean the ‘pre measured’ holes you talk about that you punch before you drill. In the PDF I don’t see where it gives those measurements. Hope that makes sense
@GrazMakes 5 жыл бұрын
hmmm, not totally sure what you mean. the dots on the blueprints is where you punch, as far as the size of the drill, its usually included with the tap which I say the size in the video. hope that helps!
@jeffreygavlik3733 5 жыл бұрын
He is talking about how there are no measurements for the layout of those holes. You have dots on your blueprint, but no measurements for how to layout for those holes
@zachdove4380 5 жыл бұрын
Yes exactly what he said, thank you! I for someone reason couldn’t spit it out to make sense haha.
@777tomwall 5 жыл бұрын
The file download works good. Thanks
@Hotled1944 4 жыл бұрын
Didn’t see any measurements in the pdf.
@GrazMakes 4 жыл бұрын
really? they show up for me. 2 and 3 inches by 7 inches. hope that helps!
@zaintaylor2358 3 ай бұрын
I very rarely Like, Share AND SUBSCRIBE, I like and subscribe a little less rarely I actually think this is the first time I have done all three of these but I did it because I really enjoyed your video and so did my girlfriend
@GrazMakes 3 ай бұрын
Awww thanks dude!!!
@ja001son 5 жыл бұрын
The link to the blueprint is only 1 page, the title page and nothing else, where is the rest?
@GrazMakes 5 жыл бұрын
the rectangles on the righthand side of the pdf are the ones you should use. do you not see them? maybe try another pdf program?
@waltparkhurst2494 5 жыл бұрын
Nice video but i see nothing on the give away. And i need one lol
@pikeevans8559 3 жыл бұрын
P.S. I kind of liked the attempt at humor.
@trabbipaul 4 жыл бұрын
Hey Dude. A verry coooool Tool. U can pay manny Monney ,or build ur own Jig,1000 times better. U get a Abo. Sincerelly Paul from Germany
@GrazMakes 4 жыл бұрын
Thanks brother!! 👊👊❤️
@trabbipaul 4 жыл бұрын
@@GrazMakes No Problem, Lol. I look rightnow ur Video from the Pizza cutter. Suuuuuper ur a verry funny Guy like me hehe.
@jimmydiresta 6 жыл бұрын
the fart was well placed.
@GrazMakes 6 жыл бұрын
Placed right in the center of the kitchen! I don't think my wife agrees on the placement :-)
@panagiwtiskalampokas9808 5 жыл бұрын
Hi !!! sent me one please !!!! very nice sharpener
@anthonypascual7145 3 жыл бұрын
How can i contact u sir ?
@GrazMakes 3 жыл бұрын
Email me grazmakes@gmail.com!
@55vdub 5 жыл бұрын
for petes sake put that tap in a cordless with cutting oil
@GrazMakes 5 жыл бұрын
who the hell is pete?
@Birb_of_Judge 4 жыл бұрын
Honestly if you manage to break a tap in aluminium without using a hammer hat's of to you.
@beno244 5 жыл бұрын
Some people make small jokes like this work, in this case it doesnt
@GrazMakes 5 жыл бұрын
thats what she said.
@777tomwall 5 жыл бұрын
OK last try. the file downloads now and says it’s corrupted. Or it downloads a few k and won’t open. I’m thinking no one else has downloaded this file? Thanks again
@GrazMakes 5 жыл бұрын
ok, changed the link again. give it another shot! i double checked and didn't seemed to have an issues!
@777tomwall 5 жыл бұрын
I spoke to soon. It only downloads 1page with the pictures of the 2 pieces of aluminum. No other specs. Sorry to be a pain. I just opened the file after I downloaded it this morning to find out it was only one page.
@GrazMakes 5 жыл бұрын
its only one page. it shows the size and the places to drill, watch the video for assembly of the parts.
@777tomwall 5 жыл бұрын
Graz Makes Thanks for your help. I’m going to give it a try.
@brucejohnson5030 6 жыл бұрын
Drill press clamps; drill press vise. Get them. Use them. The remaining skin on your fingers, knuckles and palm will thank you. Even drilling little holes like that can catch and spin those jagged bits of metal arounds at frightening speed. Cool build, otherwise
@GrazMakes 6 жыл бұрын
thanks for the input! my fingers will thank you! glad you dig the video!
@nemethlaszlo3470 5 жыл бұрын
4:45
@GrazMakes 5 жыл бұрын
ahahaha, thank you!
МИЛАНА ТУТ 👀
Рет қаралды 5 МЛН
Game Changer Amor
Рет қаралды 22 МЛН