probably the most detailed UFH installation video ever seen
@flooriqengland11012 жыл бұрын
With the use of FlooriQ Milling Machines, this process is made even easier :) great video, thanks for uploading x
@juliadallen14902 жыл бұрын
Very helpful in helping understanding and construction.
@ershadtaymourtash252911 ай бұрын
Dear Expert , Thank you for the brilliant explanation. My question is whether we can install new laminate on top of old ceramics while using a wet floor heating system. Could you please guide me on whether this would prevent efficient heating conductivity, increase energy consumption, and how it might affect moisture levels? Additionally, what steps can I take to control these factors? Best regards,
@canadapainter6583 жыл бұрын
a great video...
@tnt16022 жыл бұрын
Damn, I wish you are available in my country
@handle11962 жыл бұрын
When you mention the edge insulation, if this sits on top of the base insulation, then you ad the dpc membrane, does the blue expansion edging go against the wall as well as or instead of the kingspan? From the concrete wall inwards, is it: 1.Wall, kingspan edging, membrane, Blue expansion strip, floor screed? or 2. Wall, membrane, blue expansion strip, screed?
@omranabobakr45823 жыл бұрын
هذا عمل جيد جدآ
@jmf53922 жыл бұрын
On the blender joint under the pump is the flow inlet from the boiler below and the return to the left ??
@maurifederi5817 Жыл бұрын
Hi. Is it posible to heat shower floor? And all bathroom?
@javadkarimi9735 Жыл бұрын
Is is sortable for laminate floors? Please if anyone know
@ifti00163 жыл бұрын
Yesterday my builder applied 100 mm screed...is it ok??
@ajmalshabir40893 жыл бұрын
It will take longer to get it warmed will certainly decrease the effectiveness but don't worry it will do the job
@AN-ks2ep3 жыл бұрын
yes, we have close to 5 inch inch and works prefect
@emrahbatur26066 жыл бұрын
Ccokk güzel ya
@MarcelHVAC6 жыл бұрын
yok
@user-tn8xj6mn1w5 жыл бұрын
Welcome if you can send details about this company and address Is there a branch of the company in Iraq Basra
@taitlawrence5 жыл бұрын
Why does it have to be tested to 6 bar when it’s only going to be around 1.5 - 2 ?
@underfloorheatingsystemslt48245 жыл бұрын
Just to make sure there are no leaks, normally 24 h. Our pipe is 10 bar and 95 degree C temp,. High quality.
@daiboy80765 жыл бұрын
Is this saying it is 70 day drying time for a 50mm screed?!"!
@underfloorheatingsystemslt48245 жыл бұрын
1-2 mm a day
@daiboy80765 жыл бұрын
@@underfloorheatingsystemslt4824 Thanks for the prompt response - when would it be ok to walk on
@underfloorheatingsystemslt48245 жыл бұрын
I would check with the screeders.
@The1608795 жыл бұрын
2 months lol 😂
@simonbeckford30254 жыл бұрын
69 days is more than adequate sir..
@AlexS-mf2kc6 жыл бұрын
soo expensive. id rather 100000 feet of water hoses.... id rather simply install a normal heating. srew that. and what if it BRAKES???