I remember doing a gig as a young rock star.... at the end of each song my bass used to pick up the local taxi company. Bit embarrassing.
@thegermansat9 жыл бұрын
The hum frequency is 50Hz in the UK (and most of hte world), 60Hz for USA. It's actually the frequency of the grid, and the countries electrical network. The worst part is you also get harmonics, 100, 150, 200... which are more of a trouble for electric guitar. These are luckily much less present than the 50Hz main one.
@derrickince94134 жыл бұрын
I recall gig in Germany in the 70s at a military base using a VOX AC30 and a Strat picking up an aircraft's height and position mid song the audience loved it
@seanreed67809 жыл бұрын
One time, I was teaching my girlfriend some stuff and I heard some fuzz, turned it up and realized I was listening to radio Disney
@dillonchamberlain3 жыл бұрын
I can’t explain this but I experienced the same phenomena except it was a cell phone conversation. I live roughly a mile from a Cell tower
@seanreed67803 жыл бұрын
@@dillonchamberlain strange shit man... did you hear anything juicy?
@kylem55766 жыл бұрын
He has a bunch of tattoos, looks meaner than hell, but is most likely the nicest man on youtube
@scottestes77686 жыл бұрын
He has that English charm.
@paulturner44704 жыл бұрын
@@scottestes7768 For a South African 🤣🤣🤣
@rollingjaguar3 жыл бұрын
Paul Turner People from former british colonies in east sound and look similar.
@burresseffects4 жыл бұрын
Hey Ben. I noticed this video is five plus years old now, and having just tried shielding with copper tape for the first time, I wanted to share my experience with you. Good conductive adhesive is a lot more common now. I got my roll of tape from amazon for like $13, and if you don’t do tons of guitars it’s a pretty good deal. That said, I did what I thought was a pretty sloppy job on a tele pick guard, using numerous pieces of tape, and NOT folding any edges over to ensure contact. After covering the whole pickguard surface I got out my multimeter to check it, and the conductivity was great all over the pickguard. I couldn’t find a single dead spot. That said, might make a cool video to give some a try and show it to your viewers. Cheers!
@esa0629 жыл бұрын
What electric equipment send is radio waves too. Typically 50 Hz in Europe, 60 Hz in America, but also double that due to rectification and some equipment send higher frequencies too. The ones to block are in the kilohertz area and lower, so the Faraday's cage can have holes in it, as long as all parts are electrically connected. Shielded wires inside the cage shouldn't bring any extra shielding, unless the cavity is shielded with badly conductive paint that protects only partially. Shielding only wires might be good enough, especially with single coils that are always noisy anyway. Pickup wires should be shielded, or at least twisted. Twisting cancels interference pretty well too.
@stuartgrier56055 жыл бұрын
Greetings. In the UK, the mains frequency is 50Hz. In America it's 60Hz. I have built a couple of single coil guitars, with no shielding and had no issues from phaluroescent lights or soldering arms . I have only found issues if the guitar or amp is not properly earthed. I think American mains sockets do not have a ground connection hence the need for a faraday cage. The UK does, so I do not see any reason to do this. Its possible - probable - that I have been lucky. Keep up the brilliant work, love the videos and I love the guitars, I truly want one bit I need to save the big bucks to be able to get it.
@glennspringthorpe44958 жыл бұрын
When shielding I use 'Thermawrap aluminium foil-tape'. It is £5 for a big roll & it has acrylic conductive adhesive on it. Shield your guitar with that & buy a 1/4" roll of copper tape with conductive adhesive solely for cutting 1" lengths to solder your grounding/earth wire to. You can also use 1/2" strips to bridge the joins when using aluminium tape with non-conductive adhesive. this thin roll of copper tape is about £2 off eBay. Job done well & very cheaply 😄. Take care Ben & everyone else.
@markwarner55549 жыл бұрын
I like the black graphite shielding paint. It's easy to apply and cleans up with warm water. It's worth noting that most active pickups (most EMG, SD Blackout, etc.) are shielded internally, and thus shouldn't need shielding in the pickup cavities.
@scottestes77686 жыл бұрын
I haven't had any luck getting an ideal viscosity. Any tips?
@johnroberts8384 жыл бұрын
Brilliant Video, Thank you for the advice on folding the Copper Tape, Absolutely Brilliant, worked like a charm! In fact it worked that well that at 2 am when I thought I had finished, I plugged it in to test that everything worked there was No hum whatsoever, that being said I didn't realise that I had forgotten to wire the Tremolo Claw or my Body Ground! Admittedly there were no Strings on, but still No Hum! Thank you! 👍👍👍 Take care ♥️🎸👍. Melbourne, Australia.
@CrimsonCustomGuitars4 жыл бұрын
My pleaure, it is surprising how much of a difference the little tricks like that make to a build process! B
@SaccoBelmonte7 жыл бұрын
I've discovered that too. The problem with hum is much more related to the hot wires than anything else, if you roll some copper tape over them and ground them the hum will drastically go away, if not eliminate it altogether if you use a thicker tape. The best way I found to localize the noisy wires is by approaching them with my finger, those which happen to produce more hum as you get close are the culprit. Cover them with copper foil and approach them again without grounding, you'll find the hum is much worse. Now all you have to do is to ground that copper and voila! all the hum is gone and as you approach they will not become more noisy.
@nocturnal101ravenous63 жыл бұрын
I was going to say Dimarzio pickups are shielded, The EVO line had 4 wires 2 hot and 2 ground and a aluminum sheath under the rubber with a plastic separating layers. Fender has several guitars are no longer shielded- Metal pickguard - + noiseless pickups. Aluminum (Aluminium is the element Aluminum is the alloy as per Alcoa/Alcan/Reynolds/Kaiser) The reasoning for this is particularly with some allows there is very very small amounts of Aluminium in the Aluminum alloy this happens on a couple soft alloys and quite a few hard alloys(aerospace alloys). Also your still going to get 60-120 cycle hum even with shielding, because where is the shielding and where are your pickups at.........................not behind the shielding.
@kennethcohagen90379 жыл бұрын
It's 60 HZ hum in America, 50HZ in Europe. Europe uses an A/C transmission frequency of 50 HZ because they believe that 60 HZ will interfere with your heart if you come in contact with the current. The major difference is in the value the filter capacitors need to be in a A/C to D/C power supplies, and almost every piece of electronics uses DC, or Direct Current to run the circuit. But DC is hard to transmit over long distances. The resistance in the cable running from the power plant to your house would be enough to overcome the electric current trying to get to your home. alternating current skill suffers some losses, but will travel much farther with less loss of current. Now when that current reaches your amp it passes through wires that are run through all of your walls, surrounding your amp and guitar. The guitar's pickup creates a very small current as the strings move past the magnetic field given off the pickups magnet and being directed through the airspace surrounding your pickups small wire coils. That small current then passes through your guitar's cable, to the Amp's pre amp section which magnifies the current to a much higher degree, but with out shielding it also picks up a great deal of faint electrical impulses from everything surrounding the preamp. The windings in your pickup along with the cable coming from your guitar to the amp make a very basic antennae which picks up all sorts of unwanted noise. That's why such care must be taken to shield the guitar.
@plywoodcarjohnson54123 жыл бұрын
Interference with outside magnetic fields is probably affecting the currents in the wires so it makes sense that isolated wires solves the problem. There is also metalshielding on humbuckers. But exposed wire, such as it is when you are soldering has no isolation. So both isolated wire and coppertape should be safe. Any shifting electromagnetic field creates currents inside a wire. But if the tape has glue that is non conductive? A cage is a cage is a cage, right? But ok, overlapping tape will not connect with one another. But small gaps should not lead to fields going into the cage. If the roof is connected to the floor that should be enough. Scraping off some glue ought to work. Also you could roll the tape and create a tunnel leading from pickupcavity to controlcavity. Thereby isolating the wires. And testing the system could be done with a cellphone which gives off electromagnetic fields. An interesting way of connecting the roof to the floor ought to be the screws. If the tape goes up and covers the holes of the screws which in turn leads through the copper of the "lid". That means five points where the lid connects with the floor.A car has four connections from roof to floor. And they lead lightning on the outside. Well well.. To each his own. Trial and error!
@jatna779 жыл бұрын
Question: When designing a guitar, how do you figure out the physical balance, so that it is not neck heavy, the strap buttons are in the right positions and the upper horn, if there is one, is the right length? For example a Parker fly vs. a Les Paul.
@andrewharper16094 жыл бұрын
I remember when I got my first guitar I was sat on top of my amp and found that if I put my hand in the air I picked up a radio signal. I couldn't tell you which station as the signal was in German. In America it's 60 cycle hum, my Dad tells me in England it's 50 cycle.
@TootEmCarMan4 жыл бұрын
I know this is an older video but hopefully you will see this Ben. You talked about shielded cables, well, how about getting them for next to nothing. Old laptop wifi antenna cables. They have a single core with a woven shield and are usually of a decent quality. As a side note, if you are also in to model building then stripping the sheath and the core out then flattening the sheild then adding some black paint and you have a very convincing looking seat belt.
@2009mryoda9 жыл бұрын
Just for info, you can buy Copper tape with conductive glue :-)
@rabokarabekian4094 жыл бұрын
Aluminium adhesive tape is usually found in the hardware for use on air duct joints (he did refer to it) which is far less troublesome and at the scales of guitar signals is just fine electrically. matmatch.com/blog/materials-used-for-electromagnetic-shielding/
@sejrec565 жыл бұрын
If I close my eyes I feel like Ian Anderson is taking me through this video . Great info, great voice very professional!
@DeepPastry6 жыл бұрын
Also, maybe add twisting your wiring as much as possible. You have wire pairs coming off each coil, twist those together. Plus, you can get rolls of copper foil tape that has conductive adhesive now fairly cheaply from Amazon, StewMac, etc.
@ctrent97425 жыл бұрын
I've started running a single length of copper wire through every cavity in the body, before adding copper tape, with conductive adhesive. I used an ohm meter to confirm continuity. It seems to be an easy way to be sure the neck pickup cavity is connected.
@220467928 жыл бұрын
Played a gig in a pub where i would pick up the taxis outside. Taxi driver coming out of a 100W tube Peavey! :-)
@stankywank67078 жыл бұрын
I mostly play my guitar in the dark corner of my studio lit by nothing but candlelight, so I think I'm good without a faraday cage.
@jimmcdaniel72108 жыл бұрын
lol
@MarkLindsayCNC9 жыл бұрын
Mr. Crowe, if you don't have T-Shirts in the Crimson Shop that say, "I Blame Tom" by weekend, I, for one, will be sorely disappointed...
@NachoManRandySandwich7 жыл бұрын
Mark Lindsay Tom's the worst 😂
@Stratocaster8939 жыл бұрын
Ooh, very timely video. This is what I'm currently doing on my tele build.
@mediocrefunkybeat9 жыл бұрын
I like Radio 4! Reminds me of an old, unshielded surround sound system I had that picked up French MW radio signals during the evening. Was quite entertaining.
@FF-so3su4 жыл бұрын
Ben , you are great👍 Cat music do copper tape with conductive adhesive. PS do I also do the switch cavity and jack cavity with shielding paint?
@jamesfurz74066 жыл бұрын
The difference between shielding between copper and aluminium is that aluminium has low permeability and therefor will not block magnetic wave interference. Aluminium will stop electric field however. In the kind of environments that you'll experience at home practising are most likely electric field and coming from lights, power supplies, monitors... In a giging environment where there is a significant amount of power going around the room there is a much greater chance of magnetic fields and so copper would be preferable. As you say in the video shielded wire does most of the job for you, I don't understand why people still use single core wire inside guitars when going from pickups to switches and switches to output, its' not practical to use on all connections however... Some pickups have a reasonable Faraday cage around them, some don't.... For the sake of it just get some copper tape with conductive adhesive and do the whole lot. This way it will be as quiet as practical and in the UK can be done for about £10 a guitar. Make sure you join the different cavities together and bond it all to 0V (Ground) at a single point. This is all much more important the higher gain that you play, if you're a metal player then shield shield shield!! As much as guitaring is "old school" and people like it done the traditional way. The best, lowest total cost (in a production environment) to a low noise guitar is a well designed pickup which naturally shields itself and PCBs for the switches, pots and connection to the output jack. People don't like them, but they are far better for electrical noise, reliability and manufacturing....
@pacman_pol_pl_polska7 жыл бұрын
So you're saying shielding control cavity without touching pickups will help? Put some tape, solder it to the back of a pot and that's it?
@rabokarabekian4094 жыл бұрын
Metal pickup covers are best shielded, just in case. I used shielding "paint" over a super hot quad rial with a plastic cover to get rid of some unexpected noise. I have a light dimmer and sit near a laptop - srt of a noise test bed.
@DreidMusicalX5 жыл бұрын
I know this is an older video of yours. I also seen the shielded wire on the positive side of the guitar wiring. But I just bought some EMG RA-5 Alnico retro pickups for a guitar I am doing now. The seller said grounding or shielding is not necessary. I still have not got the guitar together, but what is your take on that? Should I still shield the cavities since there is no grounding to the body anymore, or am I just wasting time and money doing it?
@amado19572 жыл бұрын
Holy sh_t love you tools in the background !!
@CrimsonCustomGuitars2 жыл бұрын
Thank you. I have a weakness!
@al23x564 жыл бұрын
Charvel DK24 - hum when the pot is fully open or completely closed, hum disappers when touched or adjusted by a tiny fraction away from open or closed position, any idea what could cause this?
@susanroycroft892 жыл бұрын
I have an Aria Pro 11 Fullerton electric guitar ( strat. copy) floating tremelo, and there's no hum when l play through an amp. Do l need to shield the trem.cavity ?
@thysdreyer68862 жыл бұрын
Aluminium foil works the best , agreed
@jeffwinick88598 жыл бұрын
Great video. Thanks for this! One question: 8:17 you mentioned this guy now uses shielded wire instead of the tape and it works perfectly. For single coil pickups, does that mean its necessary to cut the pickup wires back to their point of origin and splice in shielded cables for those leads? How do you do that without damaging the pickups? Or is it only necessary to do this for wiring that goes between the selector switch, tone/vol pots, and output jack? Thanks again!
@tyrssen17 жыл бұрын
QUESTION, BEN: I've seen lots of vids using thin foil to shield guitar cavities. Some of the paints available specifically for the purpose look just a whole lot easier. Got a preference? Pros ad cons? (Ahh yes, I too experienced "Nigel Tufnel/Spinal Tap Syndrome" years ago, picking up radio signals ... Aaaaargh!)
@geoffdewar88455 жыл бұрын
I enjoyed this video. So many good points made.
@higler.9 жыл бұрын
I find that using shielded wire is just a pain. The shielding is so thick that it adds extra weight to the wire and your solder joints, and seems to stress the exposed wire a lot. I just fear it might snap/break at the wire. I guess heavily tinning the wire could help?
@ErikJensenDetroit7 жыл бұрын
60 Hz in the US, but I suppose it would be 50 Hz hum in the UK.
@Stratocaster8939 жыл бұрын
I'm pretty sure you can get the copper sheet with conductive adhesive. Seems to be working for me. I can't remember where I bought it though.
@barneycarparts8 жыл бұрын
+Stratocaster893 the nursery section in a Home Store carries copper tape as a snail and slug stopper.
@Stratocaster8938 жыл бұрын
barneycarparts The stuff I got was specifically for guitar builders. The conductive adhesive really goes a long way to making things easier because you don't have to worry about joining the different plates to make sure you have a electrical connection. Just stick them down so they overlap and job done. Really useful.
@mikefranks4175 жыл бұрын
I would need to test conductive adhesive actually works rather than being a market gimmick. To be conductive the adhesive would need to well impregnated with metal particles. As long as each strip of shielding touches something conductive, like foil on the cavity cover or pickguard, you should be good to go. If in doubt, a small dab of solder can be used to connect the strips. Or as others have suggested, start with a piece of heavy duty aluminum foil large enough to cover the whole cavity.
@dozukime9 жыл бұрын
Hi Ben, as a beginning builder each podcast shows how far there is to go, great. my question is on pickups, info on mag pups are easy accessible, but piezos, what are the options, do you make the casing & surround yourself? Thanks, Martin.
@learnmusic4884 жыл бұрын
Very late to the party on this one, but there’s one thing he didn’t mention... The pickup screws CANNOT touch the “Faraday cage”... _{Unless they’re ‘Not’ made out of metal, that is}_ Alot of weird things start to happen with your output if they do... so a very very small (non-conductive) perimeter around the pickup(s) screw holes are necessary..
@jeffparryncc17016 жыл бұрын
Has anyone used conductive material for lining the guitar?
@brainnok9 жыл бұрын
You mentioned using shielded audio cable instead of normal shielding via a Faraday cage. Can you please tell me exactly what kind of wire you are talking about? A link or a model name or part number would really help? Also, are you wiring the entire guitar with this stuff?
@keithhynes70012 жыл бұрын
QUESTION: I love your videos! Been watching them for years and have learned tons of invaluable info! I'm about to try shielding ALL of y guitars, ranging from cheap Harley Bentons to PRS Custom 24s, and, although I don't particularly suffer from 60Hz hum, I'm absolutely plagued by a tick which is being picked up by ANY of my pickups due to a electric fence from a neighbouring farmers field. Will this actually help or should I do something else? Really appreciate any advice on this as it's been a HUGE pain point for two years and I'm really at a loss. Thanks in advance!
@simonnylund4 жыл бұрын
You came for 2:16
@emilbergdahl30638 жыл бұрын
one quick question to you amazing ppl at Crimson: what glue do i use when gluing the foil down into the cavities if i have woodsealer on already?
@josephmorton10129 жыл бұрын
how would you take a guitar back down to bare wood if it has a transparent color like transparent red
@obus41865 жыл бұрын
Dig the Medieval tool collection. I'm sure they have something to do with building guitars.
@LeeroyMajors9 жыл бұрын
I must be lucky, no Laptop Battery issues here, in fact I find it to be the opposite, while a laptop is plugged into mains they're usually pretty noisy, but I've found when they're ran on battery there's no noise.
@Steph-de6ne7 жыл бұрын
Now i get it why he is so obsessed with Copper Guitat. Helpfull Vid tho! Keep up the hard Work!
If I'm using shielding painting of course crimson guitars brand do you need to screw a ground wire to the cavity
@CrimsonCustomGuitars4 жыл бұрын
Thank you for your support, and no.. nit really, it can't hurt but in general the pot and switch backs etc are all touching at least a bit of shielding paint and as such ar doing the same thing. I would maybe test with a meter to be sure it is continuous but that is it.. happy building! B
@jonnyrochester11415 жыл бұрын
If you don't have shielded wire, twisting the pair of wires together will cancel most unwanted noise.
@jordanharzke96433 жыл бұрын
Will a Faraday cage help with the cell phone signals too? Occasionally when I get texts, I hear a buzz in a rhythmic pattern (I'm assuming that's the data signal) come through my amp. I understand radio signals, but do cell signals react the same?
@jordanharzke96433 жыл бұрын
Hope this isn't too old to find still... Lol
@jeremypoythress12184 жыл бұрын
Will sheets of edible gold with adhesive applied in the middle of each sheet with the corners folded together work as a faraday cage? It's a good conductor but melts under hi temperatures.
@fahdchoudry77637 жыл бұрын
I saw a video of someone opening the cavity of a Gibson Les Paul and there was no copper tape/foil in the cavity. Why doesn't Gibson copper shield the cavities? Why do they not shield it at all with anything?
@AnthonyMonaghan7 жыл бұрын
Because the pick ups are already grounded...according to this video.
@golfedude19 жыл бұрын
Hi could you do a video on how too carve a maple les paul top with with hand tools and without time consuming jigs. Thanks
@mattmartinez71357 жыл бұрын
Question. My guitar has been grounded and shielded as well as uses active pickups. My problem is, the guitar makes a hum sound when I get close to it but stops when I touch hardware. My noise gate covers most of it but it's still very apparent. Any idea how I can fix this? Guitar seems to be a lot worse with passives. With passives the hum is insanely loud. Thanks!
@altrock867 жыл бұрын
Richard Martinez I had this problem on one guitar and even though it was grounded I unsoldered the ground and then re solder it and is now very quiet with passive pickups. Make sure your soldering iron is hot enough
@SaccoBelmonte7 жыл бұрын
I've discovered the problem with hum is much more related to the hot wires than anything else, if you roll some copper tape over them and ground them the hum will drastically go away, if not eliminate it altogether if you use a thicker tape. The best way I found to localize the noisy wires is by approaching them with my finger, those which happen to produce more hum as you get close are the culprit. Cover them with copper foil and approach them again without grounding, you'll find the hum is much worse. Now all you have to do is to ground that copper and voila! all the hum is gone and as you approach they will not become more noisy.
@mattmartinez71357 жыл бұрын
Thanks guys!!! I'll try these techniques. Just been living with these problems.
@mikefranks4175 жыл бұрын
Richard, I had exactly the same problem, so bad I was planning to overhaul the guitar. Then, completely by coincidence, I happened to use a different cable, no more noise! Just sayin, might be worth a shot. I also agree with others who have mentioned cold solder joints. These won't show up with an ohmmeter, but it takes only an hour or so to go through the whole guitar. One final thing - make sure the jack is in good shape. These take a lot of wear, may get sloppy, terminals may crack, etc. A decent jack can be had for under $10 u.s.
@sleepy226026 жыл бұрын
you need a vid on how to stick tape in a cavity?
@plywoodcarjohnson54123 жыл бұрын
With killer snails (who can't stand sliding over copper) the price of copper tape has probably gone down. Ten meters is now 100 SEK. (Ten pounds/dollars).
@BodominLapsi959 жыл бұрын
Hi Ben! I'm about to start a new project, a neck-through Flying V with flame maple top and binding. How would you route for the binding channel for the maple top? My concern is the neck heel area, where it's impossible to get it routed all the way up to the neck (hope you understand what I mean). Would you recommend finishing the top to the stage where it is bound before gluing it to the body?
@sapphirestrat9 жыл бұрын
Hey just a quick question, if i were to use shielded wire.. would i then ground the outer shielding to say a pot or other ground?? thanks
@pauledwards89477 жыл бұрын
copper tape..most gardening kinda places sell copper tape for use as a slug barrier...guitar related sites prices seem to be twice as much forsame...
@leoryan997 жыл бұрын
paul edwards I use slug tape
@majesticmaricachicken60226 жыл бұрын
How do you route/drill the neck pocket is there a specific angle or is it just a 90° or does if change for a Bolt on neck ?
@pastorkev7775 жыл бұрын
What is your opinion of shielding paint?
@prograven48447 жыл бұрын
my bass is all sealed and still it has a weird hum.. when touch on the pole piece on the pickup
@Crisis_Brew7 жыл бұрын
grounding issue
@ebandcamp4 жыл бұрын
60 cycle hum !
@MrMuncieman6 жыл бұрын
I did not have the time to watch this video but is it true that aluminum foil will work just as well as the stickon Copper shielding? I am building a Les Paul guitar
@manojghimire88796 жыл бұрын
Hi,Crimson after watching your video i tried sheilding my lespaul standard guitar but the neck pick up doesnot sound after that other are perfects there is no more hum sound .Please help me.What may be the problem.Does i have done it wrong way? Could you please make a video for it? Thankyou
@eirikstorvik24137 жыл бұрын
Could you then wire in a small antenna or pocket radio to your electronics and use radio as a backingtrack :P
@U014B7 жыл бұрын
Even better: you could use it as a noise waveform generator to control with the guitar.
@add-1232 жыл бұрын
People use carbon and graphite with acrylic paint but iv got some titanium dioxide and NASA use that and I have lots has it been used in guitar cavities do ya know
@technicstim6 жыл бұрын
hello could anyone advice me on the sheilded cable size or provide a link. thanks for great video :-)
@louh92119 жыл бұрын
Hi Ben, love your podcast and channel. I'm building my first bass. I've got some 90's Fender Jazz pickups that came out of a MIM J bass. It seems to me like the magnetic field is weak. I've compared them to some cheaper J pickups that I bought for my daughters bass and those $25 ebay pickups are much much more magnetic. Should I be considering RE-magnatizing? Part 2. The 90's made in mexico JBass pickups are the same width for neck and bridge position. I'm considering slanting the neck pickup to hit the strings between the poles. (much like Larry Graham did) Any advice here? Thanks Ben!
@DavidPatersonPortraits5 жыл бұрын
Does the bridge have to be earthed? My cheepo isn't.
@CrimsonCustomGuitars5 жыл бұрын
There has to be some sort of earth between the strings and the Jack, most commonly that is at the bridge but could be tail piece etc. B
@ranrjbneztnarf89327 жыл бұрын
You seem like a humble man. I like that. Good content ಠ_ಠ
@TheDracfink9 жыл бұрын
what are your thoughts of shielding paint?
@CrimsonCustomGuitars9 жыл бұрын
TheDracfink it is pretty expensive and needs several coats to be effective.. I like it in principle but when there are other options that are foolproof I tend to go with those... currently!
@thumbslam19 жыл бұрын
Hello Ben..what glue do you think is best to use in gluing up multi-laminate exotic "possibly oily" necks? What will glue and add the most strength and have the least amount of cratering and movement and hold different woods together through the ages like wenge, maple, rosewood, purpleheart, cocobolo etc...?????
@CrimsonCustomGuitars9 жыл бұрын
If you're worried about oily woods then you can use acetone or similar to rub down the gluing surface an hour or so before you start clamping up.. However, I have found that polyurethane glue works on pretty much anything.. Messy stuff but very very good if you're worried about delamination. Always do a test glue up with scrap cost though imo.
@thumbslam19 жыл бұрын
Crimson Custom Guitars Thanks Ben you are incredibly generous with your time and information. I was thinking of that exact method sanding, wiping down with naphtha and using the poy glues. I had read somewhere that it’s not as strong as say Titebond original but does play nice with oily woods. Strength is a big concern as I’m building 5 string basses and some with fanned frets so the necks will have a lot of tension and long span length wise. Thanks again so much for your input...
@CrimsonCustomGuitars9 жыл бұрын
My pleasure.. I really don't think there is much difference in strengths between the glues, if anything I think poly is better as it doesn't delamination with heat or moisture in my experience. Have fun, sounds like great builds!
@Luciffrit7 жыл бұрын
Would silicone adhesive work for shielding? Silicone is a semiconductor.
@larrythecomputerguy6 жыл бұрын
Most silicon adhesive is NOT conductive---often used as an INSULATOR!
@grahamkelly82994 жыл бұрын
Skip first 3 mins
@BigWilleyMusicandFun9 жыл бұрын
very good info thanks
@CrimsonCustomGuitars9 жыл бұрын
My pleasure, thanks for watching :)
@sirclerox9 жыл бұрын
Hey Ben! I was watching the podcast I missed during my holidays, at the Kathmandu airport, (I gotta say, internet is quiet awesome for that!), but anyhow here is my next question that has been on the top of my head for bit: What would be the advantage, if there is one, to have on any fretted bowed instrument, a deported nut and thus a scale that ends up at a fret, that I would call the " fret 0", situated a few millimeters before the nut? I have seen this on high quality (German?) Bass guitars and more recently in a Nepali music shop full of horrible copies of Gibson's famous with that very feature, so far I still don't believe that Gibson or any other major brand is doing such a thing. It really had me thinking why would a third world manufacturer would bother with something that add extra work? And does it really change something? The only thing I could think of was the open string sound consistency but it doesn't work for the German basses as they use brass nuts... Maybe it is to make the instrument set up easier so you don't get a "fret1" Buzz which easily occur on 5 or 6 string basses. ... I don't know this thing is driving me "nuts"!!! I thing is for sure, it adds an interesting visual feature! Ps: does this really look like a question? You probably spend more time reading this that you need to answer !!! Ha! Another C-Bomb! Peace out😁😛😁
@murfbass4 жыл бұрын
The question common to every Ben video is how long will it take before he gets to whatever it is he meant to begin. The second question is how long will it take before he starts babbling about irrelevant things again. Ritalin Ben ritalin. Also, how long before he realizes a faraday cage is useless if the thing it is protecting is grounded to the cage walls?
@t0ddbr0wn7319 жыл бұрын
Should beginner luthiers buy S.A.E. Or metric tool starter kits and what your opinion on Fanned fret guitars. Have you built any? Thanks love the podcast Todd in Ky USA
@vformarallo9 жыл бұрын
He has a video where he draws a fanned fretboard if you re interested
@Hornblas1894 жыл бұрын
Only one system has made it to the moon my dude...and it ain’t metric.
@thomasshore20694 жыл бұрын
The operative word is cycle, 60 cycle hum!
@willturner8039 жыл бұрын
There's no beating a faradays cage in my opinion. It's foolproof.
@tonecontrol9 жыл бұрын
I would love to know how to shield a semi hollow or hollow guitar.
@faurana9 жыл бұрын
the concept doesn´t change: put conductive material around your electric wires with as little gaps in it as possible and then connect it to the ground. note: make sure not to short circuit anything with the shield.
@tonecontrol9 жыл бұрын
faurana Thank you! But I guess I'm wondering about the actual technique to do so, seems a lot harder than a solid body.
@faurana9 жыл бұрын
AdrianTracks well, can´t exactly help you there, haven´t done so, but asuming you want to have as little stuff inside your acoustic cavities, in that case shielded wire would most likely proof to be the most simple and effective solution. if that is not available you could go with cutting thin straps of aluminium foil and wrap it around pairs of wires (again making sure there is as little gaps as possible). wrapping the positive and neutral connection wire together in one "package" and connection each single wrap end to the negative connector. this would actually mimic what shielded wires themself do, though shielded wires usually use a woven shield, or if you have a very fancy shielded wire, a combination of woven and wrapped shield (random trivia)
@Bloodysugar7 жыл бұрын
It is a lot harder especially if you want to fill a 335 or so with copper film XD Maybe making a little Faraday cage of copper wires and fixing it around pots would be easier... But well, using such feedback monsters... little electromagnetic bugs shouldn't bother you much more : find the good spot where you're not making your amp scream and don't run around. ;D
@bullerfugl7 жыл бұрын
depends on how hollow the guitar is, if its alot, i would find a small(something like a large mints tin) case and then run the electronics inside and shield the inside the tin
@guitarwhores7537 жыл бұрын
How do you light your vids? You have great lighting. -Zach-
@mbrown54947 жыл бұрын
So, why not a big piece of kitchen foil? It's electrically the same, and all you are doing is controlling the ground signal. It's a field concern, not a conductive concern per se. I've never done this, but would bet my left nut that there is little/no difference in noise between standard kitchen foil and any other shielding method.
@cbfedge55936 жыл бұрын
Michael Brown correct
@jeremiahstaggs3115 жыл бұрын
In my experience aluminum tears more easily. It also absorbs less interference than copper. I have actually noticed a difference in the noise level in cases of extreme interference. and copper seems to stretch a bit more making it easier to install. that my two cents
@Drewcifer19727 жыл бұрын
Have you ever considered conductive paint?
@suspectdown51337 жыл бұрын
Andrew Olmsted - I had a experience with the conductive paint. I rebuild and fix 1988 Casio PG-380 synth guitars (look them up) I own a new one I bought in 1989. Had bought a few off of ebay to rebuild.These guitars were manufactured with the black conductive paint lightly sprayed in the entire cavity front and back. I received the guitar from ebay and started playing it (not plugged in) and it felt different than mine,the resonating in the guitar seemed deader than mine more like a thud,these guitars have very little wood to fit the synth and electronics in it. I opened it and someone had used the black conductive paint painted on real heavy in all the cavities. It did affect the feel of the guitar.I did check mine with a meter and the paint was working fine,I would say use it very lightly IMO. EDIT; I think you will find the copper conducts better and is less mess.There is a video of a guy doing his guitar with both and came to the same conclusion.He also used a guitar string with holes to connect the front cavities to the back and showed with a meter what was going on.
@Barrygee9 жыл бұрын
spray adhesive and aluminium foil from the supermarket works just as well and costs next to nothing....just think how many guitars you can do with a roll of good old baking foil
@scottestes77686 жыл бұрын
Yeah,..........but copper is fancy and it makes me feel good inside.
@83roadstar5 жыл бұрын
Copper also solders a lot nicer than aluminum foil
@lignumsus63938 жыл бұрын
Hope this makes my guitar stop picking up radio stations.
@elymolloy83335 жыл бұрын
go immediately to 4:41 for a good laugh.
@dazarp7 жыл бұрын
brilliant
@1980bwc6 жыл бұрын
Instead of giving the pros and cons, you gave two pros! Lol. It's 60 cycle hum. Cheers!
@StephenKramerstevefunk5 жыл бұрын
you're from SA originally right?
@WutipongWongsakuldej8 жыл бұрын
I would worry about the chargers before laptop battery :).
@quasiczarcasm9 жыл бұрын
I would pick up airplane radio communications before I shielded bass.
@CrimsonCustomGuitars9 жыл бұрын
Wow, I would bane seriously left it unshielded busy for the sheer awesomeness of that :)
@quasiczarcasm9 жыл бұрын
+Crimson Custom Guitars It was pretty cool for a while but the interruptions my to practice became annoying. It did inspire me to get a radio scanner so I can still listen to them more clearly.
@utahnick8 жыл бұрын
+Honor of Týr lol 👍
@melexdy8 жыл бұрын
+Honor of Týr Are you sure your socket was grounded?
@blackie757 жыл бұрын
I'd like to see some study into shielding. I recently shielded my stratocaster, and it made no discernible difference whatsoever.
@sinr7643 жыл бұрын
less talk, more do!!!
@jvin2489 жыл бұрын
+1 for the aluminum flashing tape, it's thicker than normal kitchen foil. Had a roll left over from a roofing job and used it on two noisy guitars, slated for two more. Shielded wire source is old RCA cables from the VCR/stereo days. Bought a used flying V before that was really noisy; did the cage and it helped as much as any but the huge fix for that particular guitar happened after replacing the very long output jack wires with shielded audio cable. If that had not fixed that one I would have done this to it "star grounding" www.guitarnuts.com/wiring/shielding/shield3.php .
@brainnok9 жыл бұрын
+jvin248 What kind of shielded audio cable did you use? I am trying to find some.
@jvin2489 жыл бұрын
+blahtalk .. en.wikipedia.org/wiki/RCA_connector cut the plugs off and use the wire. I have found some of these wires not properly shielded: effectively only a twisted pair, that you don't see until you cut the plugs off. It should have a center conductor, insulator, then wire/foil wrapping, plus outer insulation cover.
@brainnok9 жыл бұрын
Thanks for your help! I'm going to try to find some without RCA plugs attached.