You are a great teacher. Keep doing it.

Always fun to check out your videos, thanks for being back!

Brilliant. Really clear help with cb 750 carburettor assembly.

Glad to have you back I know for one I missed them

Excited to follow the rest of the rebuild! Hope you enjoyed your time off!

I have to say, I have literally watched the entire 27 episode series thus far in about a week, and they are awesome. I love the fact that you show all the steps you have taken to put this bike back together. also you and these videos has inspired me to build an older bike and tune it and make it they way I want it to be. thanks for putting in the effort to really make these videos something great!

Just wanted to say thanks for these videos! I have a '79 CB650. It has the worst carbs ever designed. After seeing how easy these carbs were, I scoured the forums and found where they'll fit the 650 with one mod. I bought a set, rebuilt them and finally got my bike running reliably for the first time in almost a year.

Welcome back Deano. I have been rebuilding my CB500 at the same time as you however you have always been a few steps ahead of me. That was until you went away for so long and left me to figure it out myself...! I had the same problem as you with my carbs except the previous owner hammered the rod out busting the retaining pin off. I drilled out the hole and cut a flat headed, ridged nail to 11mm and pushed it through. Works perfectly. Thanks for all your videos, been following you since you started the Sabre Project.

I really appreciate this! helping me out big time on my '76 CB750! thank you!

Glad to see your back. Picked up my dads 69 CB750 last summer and these videos are going to come in handy once I get started on it.

Great to have you back and glad you got some rest to recharge.

Christmas arrived early! Good to have you back. Your videos has convinced me, that with the help of a Haynes, the workshop manual AND the hackaweek videos I Can fix just about anything on a motorcycle. So I finale got my licence and bought a CBR600 from 1990. At the moment ses torn a bit apart, a few parts being stripped and powdercoated, I changed the sprocket bearing and the fluids. Next up will be adjusting valves, so Ill rummage though your videos to find that chapter.Thanks for the inspiration!

So awesome that you are back. I really missed your videos.

so pumped to see you back ive checked every week for the last few months to make sure i didnt miss anything! welcome back i hope you had a fun vacation! ~ Spencer

Ain't got the time, space, money or even bike to twist spanners on but goddamn, I miss my bike, so I'll watch you instead! Wish I lived nearby, I'd offer a (free) hand! Thanks for posting!

Great to see you back, Dean 🏍

welcome back from your much deserved break! love your channel! keep on Hackin

good to see you back Dino, I have been waiting for this one. Gotta rebuild my dad's 76 cb750 carbs

Man I loved the CB's! Good to see another video from you! I've used some brass tipped set screws before that had a small stem on them like your little shaft in the stay plate needs. Might be worth looking into.

glad your back and looking forward to more hackaweek

I've missed you! thanks being back!

Thumbs up. Nice to see your back on the air. Iv'e been following your tweets as well.

Good to see you back!

glad to see you back..

I have missed you man!... So happy you're back :D :D

Great stuff Dean, normal service has been resumed :)

Dino's back... all is right with the universe...

I wish I would've found this channel before I did mine by trial and error. What a pain that was. Haha

Good to see you back

Hes back!!! Finally!

aaaah extrañaba estos videooos =) me voy a preparar un cafe y a mirarlo saludos

Finally you're back!

Welcome back!!!

welcome back mate 😊

I noticed something in your first upload but said nothing because anyone smart enough to rebuild a monster like this should easily recognize a video clip portion which has been captured in a mirrored image and realize that the machine they are working on will look the opposite. I watched this repost and found only this difference corrected. So did I miss something else? My congratulations on your creating very informative and precise videos specific to the machine you are working on. Obviously you leave no boxes unchecked. Merry Christmas and may God bless you and yours.

Welcome Back Dean!

Hi Dino, Welcome back! I really thought you were going to say "let's stop yakkin' and get on with hackin'" LOL If we don't see you before, I'd like to wish you and Lisa a wonderful Christmas!

The pin is design to keep the shaft in place and allowed to rotate in the same time.To correct it,you could tap the hole according to a set screw that you'll grind the tip for the fit you need and a drop of lock thread to keep it steady and voilà!

Pod filters are 100% ok on these engines. The only problem i had was the weight of the carbs bouncing and destroying the rubbers. I made a bracket bolted on the engine underneath the carbs to support the weight.

Welccome back, Dino... :-)

YOU ARÉ AMAZING. SO THANKS

Hey, by the way, those fuel tee o-rings at 6:47 are available on eBay in a kit of 8 as well.

Maybe a small ball bearing in the hole captured by a threaded plug? The ball would rotate in the slot and capture the shaft.

Hey! First of all thanks for these awesome videos man, they are really really helpful. Question: Did you use the original jets in these carburators, or you got some more "opened". As far as I know if your air intake will be larger (4 filters) and also the stock exhaust will be replaced, you will need more gasoline to mix with the air. Am I correct? Thanks again man and Cheers from Argentina!

great video. why not make 2 channels on the shaft and use "c" clips to maintain the alignment?

Just HAD to upload a corrected version! Several video errors to fix. :)

Drill and tap and insert allen grub screw into carb shaft?

Hi, how about machining two circling grooves either side of the boss they would be less fiddle and more secure.......

Hey Dino, I have a 81 cb750c I think it has 120 main jets and its running lean with pods. I decided to mess around with and I put the airbox to see if it'll run better and it didn't turn on. I messed with the air/fuel screws (yeah I know bad idea). But I decided to order the stock jet kit. What advice do you have?

Ah factory manuals, there is probably a supplement for that one you have that covers the later carbs, that's how Honda used to do it. Then later they might do a manual that combines the original manual and the supplements, 6230010 I think it was, but long obsolete of course.

Hi Dino I have a set of carburetors for a cb750. The bearings for the rod in the carburetor rack are worn. Do you know what to do to replace these bronze layers? Do you know where I can buy new ones?

1:20 you missed an opportunity... "enough yaking... (let's get hacking)"

I recognize that shirt! You must be from DUrham. lol

Need 4 top slide seal can't find that seal.

Ah, so the first video was mirrored? Thought it was a bit weird with the big Phillips screws being left handed, but you know, Japanese, seventies, plausible :)

Do manuals for newer models use 3d computer generated graphics or are they still hand illustrated? I would imagine computer generated to be more economical... If so, are they better than the hand illustrated drawings, about the same, or worse? Also curious if manufacturers make 3d models available?

Where can I buy a carburetor rebuild kit for a Honda 1971 CB 750 K1 and a 1974 CB 750 when I turn the gas on the motorcycles start but gas continues to run out of the tube on to the ground or leak

Are we going to get any Hackaweeks on that lathe?

😍☺☺

🤔🤙👏🙇‍♂️

so where you been? dropped out of the race for the Republican nomination?