Hall effect RPM Sensor for Taylor big bore RC engines

Рет қаралды 259

Ай бұрын

This video is part 2 of the wireless SCADA for RC's. I give a quick review of various ways to grab the RPM's with some scope profiles of the ugliness that comes off the ignition system. I conclude with a DIY hall effect sensor that gets "shoehorned" into the tight flywheel housing on these Taylor big bores

Пікірлер: 24

@RCRoads Ай бұрын

Nice job Brian. Your test bench reminds me of an aerospace lab. Very impressive design. I think you need to sell your creation to Taylor. 👍👍🏆🏆

@RCWalletVacuum Ай бұрын

Thanks RC, i just wish i had the budget of one of those aerospace labs. Thanks for checking it out buddy

@kgm5512 Ай бұрын

Mad scientist make my brain hurt lol. Not sure how many of the words I understand but this project is awesome! I guess I never really understood how these are developed

@RCWalletVacuum Ай бұрын

Hey Kyle, when you see the electrical "chaos" that comes off those magnetos, combined with the very sensitive electronics in things like the receiver, its amazing these vehicles run reliably. Thanks for checking it out buddy

@SteelCityRC Ай бұрын

Good stuff! Thinking outside the box. Making your own is where it's at. Nice work

@RCWalletVacuum Ай бұрын

What's up G Man! Thanks, now hopefully i don't start it on fire, lol. Thanks for checking it out

@SteelCityRC Ай бұрын

@@RCWalletVacuum 😂

@alterdcustomrc4512 Ай бұрын

You just made an episode of how stuff works!..man awesome! Soon we’ll see rpm on our remotes! Maybe be able to adjust timing on the fly

@RCWalletVacuum Ай бұрын

Hey Alterd, thanks for checking it out and i'm looking forward to see how your upcoming builds come together

@rcOhio Ай бұрын

very cool! Loving your research Brian! I definitely like the clean signal from the Hall effect. the little digital monitor is legit too! I highly doubt Mike would void your warranty with the clean intelligent work you're doing! thanks for continuing to share man!

@RCWalletVacuum Ай бұрын

Thanks Todd, i just wish Mike would send me more engines to test! Good catch on your part with the Typhon servo situation from Kyle's video. There is no replacement for experience. Thanks for checking it out buddy

@rcOhio Ай бұрын

@@RCWalletVacuum thank you 😉 Wish Mike would send you engines too!

@5thscaleaddict Ай бұрын

Good stuff, buddy 👍

@RCWalletVacuum Ай бұрын

Thanks Addict!

@SlickTrickRC Ай бұрын

In the end you will be able to tune for ALL weather conditions. Ill have to take your word on all this. A bit over my head... i got stuff i bought last winter. Now i forgot what they are and what they are for.

@RCWalletVacuum Ай бұрын

Hey Wally, on another subject, did you catch the video of " potus poopy pants" crapping himself on stage in Normandy?! My god how pathetic!

@SlickTrickRC Ай бұрын

@RCWalletVacuum I can't stand to watch that abuse of an elderly man. Sick bastard. Creepy Joe. Nasty. No, sir. Can't stomach television. If it weren't for my rc hobby, I'd almost never watch any television.

@Thunder_Road_81780 Ай бұрын

Very interesting 🤙

@RCWalletVacuum Ай бұрын

Now i just have to keep the flywheel from tearing up the wire. Thanks for checking it out

@jukkaovaskainen Ай бұрын

👍

@nzmikec Ай бұрын

Hi Brian, im using a similar Hall effect sensor to pickup RPM on my arduino project. My engine uses a similar ignition, and im able to trigger the Hall effect sensor by simply zip tying it to the outside of the coil. I assume theres is enough magnetic flux transmitted through it to trigger the hall. I also had some luck zip tying the Hall effect sensor directly to the spark lead. It did work, but the coil seemed to give a better signal. Might simplify your setup. Nice video!

@RCWalletVacuum Ай бұрын

Hey NZMike, what a great idea. I was trying to keep the hall effect as far away from the coil as i could do to emi, but it sounds like that may not be a problem. Perhaps the Schmitt trigger in the chip is the saving grace. Thanks for the tip and thanks for checking it out

@nzmikec Ай бұрын

@@RCWalletVacuum 3364Q is the sensor im using, zip tied to the steel laminates of the coil. Cheers.

@RCWalletVacuum Ай бұрын

@@nzmikec Thanks NZMike. I'll go check out the datasheet