Такова у них условия работы, ужасающая картина , мы от такого рабочего цеха сразу же убежали! Дай Бог им здоровья , счастья и удачи ! (это в Пакистане или же в Индии наверное )

Bugger you keyboard snow flakes,just think of what this team of gents could do with a little H@S and the correct tooling.

Cool

техника безопасности на высоте, не слышали, а где она , нету а на хрен она нужна , итак сойдет.

​@@huseynrzayev9952Пакистан

... может и бессмертный но в розыске ! 🧐🤪

Сварщик даже не смотрит что он там варит тыкает куда попало,😁😁,просто какой то пипец .

А почему сварщик в кроссовках а не в шлепках? Непорядок...

​@@user-pu6te9zk3g😂😂😂

@@user-qy6rr4tu3y да ладно, а вы я так понимаю просто гуру сварки,мы тоже не лаптем щи хлебаем.Они как лепили горбатого так и продолжают.

трактор медленно возит.. наверное только поэтому.

троллейбус рассчитан только на одну поездку.😉

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Eyrt8e37eutrwu

Seems that eye and foot protection is overrated at least in Pakistan.

Calling them welders is a stertch.

If there that stupid .so be it

)

а что это такое...

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Сделайте что-нибудь еще.

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

100%

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

бабы еще нарожают. они там как тараканы размножаются

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

*6 tons of steel scrap :D

@@AKAtheA Yes, good point. The whole trailer was made out of literall scrap but may not be that bad thing since, as far as I know, most of metal available (per price) in Pakisatn, Bangladesh, Sri Lanka... comes from ship breakers that cut old ships and sell the metal. Since shipbuilding is quite regulated (it should be, I hope), steel quality should be relatively good (most of ships are built out of EN S355/ DIN St52-3 steel). The real issue is that, since they do not have metal available in standard dimensions (here in Europe steel beams in all forms are available in 6m (approx. 20 feet) or 12m (approx. 40 feet) they make beams for chasis by welding smaller pieces together to get to the desired length. Beam welding is not a bad thing (if done properly) but they definitely have way to many welds on main chasis and each weld zone is potentional crack zone. There are few design flaws / weak spots too. Connection between main chasis and axis is very weak for a trailer of this size, hinges connecting the lower and upper chasis are very weak too, lift mechanism is very crappy, movable parts with steel to steel contact under high load - it will wear in no time since there are also no lubrication/grease nipples.

Туда только электродов тонна ушла

😂😂😂

Safety 1st👍

Так они могут собрать ка 52 верталет

🤣🤣🤣🤣@@user-du1uz5lf4p

Если эта телега по жизни будет стоять, а не ездить, то смысл в ней есть. А на ходу конечно разваливаться начнет. По виду тележка тонн на десять- пятнадцать.

@@georgyvahrushev3908 у них электродов и ржавого металла дофига, будут регулярно чинить тележку. И все будут заняты. У всех будет немного хлеба для детей. Так и будут жить веками...

Советский союз помог

сша дал ядр пакистану а , СССР дал ядр Индии чтобы эти 2 армии в ночнушках не пересеклись..

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

They can make furniture out of a pile of shit.

It will be good for 30 ton that trailer..😆😆😆

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

It is not certain, the human is not taken into account in these countries, it is just a consumable that is replaced when it no longer works. It costs less to replace it than to equip it with protective equipment. and as for the training of new workers, seeing the quality of the work done, it's not super quality, but rather very basic, you just have to see the rust provided during construction, unthinkable in our factories or workshops.

@@harentroisthat's a sad reality in so many areas of the world. I watch alot of videos like this. You speak the truth about the lack of concern for human health and safety. It's crazy how many workers are barefoot or wearing sandals.

@@harentrois I agree with all except I wonder if your assesment that it costs less to replace a worker than to provide rudementary PPE is correct. In this setting It seems to me that it would cost more in lost production time to replace and train a worker than to provide him with a proper welding helment, welding gloves and leather apron and mandate long sleeved shirts. I understand work boots, or steel toed shoes and breathing apparatus are not happening. Those welders and helpers are blind men walking. One of them was staring into the arc as he was running the bead. The helpers were actually holding the work piece bare handed as it was being welded. Insane!

@@sunny71169 No wonder they have to curse their god minimum 10 times a day.

​@@harentroisyou people have passed a very difficult time to reach present day status. Usually Western people hide their ugly faces. I saw old videos of their factories, people working in coal mines, chimney cleaning boys etc. Pathetic.

Им виднее, куда и сколько металла нужно потратить

Варить без сварочной маски! А вы попробуйте!

@@user-jx4bn2iv7v я и говорю! Эти люди могут все! В молодости бывало варил без маски, теперь глаза болят...

А ещё излучение от сварки рак кожи вызывает, как и при ядерном загаре!

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Вероятно у него и халат из негорючки, в отличии от других

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Да, без тесьмы не пройдет техосмотр

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

​@@user-le4ec6ii7d idiot spammer

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Il. Concetto. E'. Giusto.... gran. Esperienza.....💪✋👍👀🇮🇹🇮🇹🇮🇹

they dont even know what ISO 9001 means

l ıake you comment- bravo ! Thank you!!

​@@jemandjemand2362it's obviously standard Pakistan has so many companies working professionally in different sectors these are just street service providers across highways & heavy traffic roads to provide cheap work in immediate solution...

​@@jemandjemand2362how come you jumped into this conclusion. They know ISO 9000,as well as, KAIZEN. The problem is those who have adopted these standards usually never allow these youtubers into their premises.

Телегу надо проваривать пол дня. Шоб не развалилась. 😅

@@user-yh6dr9jn4x Это тебе не Автоваз , болты не забивают кувалдой ...

@@Bosjak63 какой алковаз?

Пакистан основная мировая разборка морских судов. Оттуда скорее всего б.у. металл

Pakistan itu bukan india

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Share with us your way of automated production........ Preferably on your channel.

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

@@user-le4ec6ii7d That will probably happen in the next millennium. Priority is inventing chairs, tables, workbenches and, of course, toilet bowls.

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

\\

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

OH Dear.

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

В какой стране ты живёшь?

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Ни я йп

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

یہ لوگ پاکستانی مزدور ہیں۔

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Eine Mischung aus 12. und 19. Jahrhundert. Die meisten Arbeiter krepieren schon nach kurzer Zeit oder landen als blinde Bettler in der Gosse.

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Да.,тот молодой вообще без масок варит отворачивая голову в сторону, неужели все швы будут качественные или.он уже. по привычке варит --удивительно 😨

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

and they're not going that way, as what they make seem to be 'good enough' for it's customers and price class

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Если им полуавтомат дать так они из и в Россию поставлять начнут 😂

BOM 💥

Сравни с Буханкой и удивись ...

Наверно из-за санкции Металлом Южный Порт продаёт им за клпейку 😀😀

Пакистан из за дешёвой рабочей силы является основной мировой разборкой морских судов. Им ещё и деньги доплачивают за утилизацию. Оттуда и дешёвый б.у. металл.

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj