Review of Harbor Freight, Chicago Electric Portable Torch Kit with Oxygen and Acetylene Tanks (Item #65818)
Пікірлер: 648
@PorchPotatoMike4 жыл бұрын
“Didn’t have a use for it at the time, I just wanted it”. Yep! That’s how I buy most of my tools!😀
@jster19634 жыл бұрын
MeanMad Mike LOL! I’m glad I’m not alone 😬
@horaciosalinas81453 жыл бұрын
✋
@MadebyKourmoulis3 жыл бұрын
I'll usually have a project i could use a tool for and think ill use it all the time. I'll get it use it for the project then hardly touch it. The kicker is when I pay more for the tool than if I just bought the thing I was making.
@anthonydawson49092 жыл бұрын
Lol
@waynebeaver40962 жыл бұрын
Couldn’t agree more with all of the above comments.
@robertoswalt3197 жыл бұрын
Tips from someone with some experience. Make sure you tighten the valve on the bottle well when you are through otherwise you may not have any gas when you try to use it next. Leather shoes can save your foot from a serious burn from slag (it happened to me.) Wear long leather gloves. The metal stays hot for a long time and it will burn unprotected skin extremely fast. NEVER weld or cut on concrete. Concrete contains a lot of water which will cause the concrete to pop sending hot pieces of concrete flying. Finally always wear eye protection. Sorry to sound like a safety cop but there is a real risk of you aren't extremely vigilant. Good luck with the torch. PS wire welders are fun too.
@jster19637 жыл бұрын
LOL! I love safety tips! It's funny you say concrete will pop. I learned that right on this video. My very first time trying to use it I touched the flame to the concrete and it popped and threw "junk" up in my face! I'm sure glad I had on the goggles. I do have a wire feed welder and am learning that too. This metal stuff is fun.Thank you so much Robert and I'll try to stay safe.......
@Fireship17 жыл бұрын
+jster1963 go to a masonary supply and get some fire bricks. They build the inner chamber of fireplaces with em. You can arrange what your cutting or heating on them and they will take all the heat you can throw at them without explosive popping.
@justinmcdonald33766 жыл бұрын
I prefer rod but welding can be fun
@jster19635 жыл бұрын
I'm not offended at all about safety advice! I love to get advice from guys that have experience. Thank you for your advice and I will take that advice. Thank you again......
@raulmateo69775 жыл бұрын
Thank you for the tips sir.
@rodneyrodney90823 жыл бұрын
I've been thinking of getting one of these for many years and I just decided to do some research and your video was the first one viewed, I think you did a great job and I'm inspired even more after your presentation. Thx for sharing.
@jster19633 жыл бұрын
Thank you! I hope you like yours....
@eviltwinx7 жыл бұрын
Thanks for the write up! I've been interested in Oxy/Acet for awhile and I even took a basic class to learn. I thought it might help with my blacksmithing by isolating a small area to heat and bend. Now you got me thinking of getting a set!
@jster19637 жыл бұрын
You need one! It heat up metal FAST!! And thank you very much.......
@MrDad-ok8qe3 жыл бұрын
I really appreciate your humility here. Super refreshing in this day and age, thanks for uploading.
@jster19633 жыл бұрын
Thank you very much!
@ianvansice92276 жыл бұрын
Really enjoyed watching. I'm the same way, not an expert but I love to try new stuff with cool tools. Thanks for sharing
@jster19636 жыл бұрын
Ian Van Sice Thank you! I appreciate the kind words......
@TheDavidFromTexas6 жыл бұрын
Newb that hasn't welded or used a torch myself, THANK YOU SIR for your review on this!
@jster19633 жыл бұрын
Thank you Sir!
@stevefraser98864 жыл бұрын
Thanks for the vid! I'm going to pick one of these kits up. Appreciate the time you took to demo as a 'noob' to another. Thanks!
@jster19634 жыл бұрын
Steve Fraser You’re very welcome! Please be careful because so many pros have warned me to be careful. And thank you very much.....
@joesangster65907 жыл бұрын
As an apprentice HVAC Tech, Steam Fitter & Plumber, used a rig similar to yours for soldering & brazing copper, as well as small torch jobs, the smaller bottles surely makes it very portable. Your becoming proficient in many different trades, keep up the great work!
@jster19637 жыл бұрын
Joe Sangster Thank you Joe! I'm really enjoying myself in the shop! I've seen the HVAC guys use the rig you described. I talked to a couple of those guys about it. So far I love it for my home shop. Thanks again.....
@jessihawkins91169 ай бұрын
can’t you use propane for that
@daltonjones47126 жыл бұрын
I love the lil speech there at the beginning I believe this is the very best way to learn find something your interested in watch how it's done and give it a go. Good for you bud thanks for making this video
@jster19636 жыл бұрын
Thank you so much! I do my best learning from doing. Thanks again.....
@michael1026 жыл бұрын
I have had this set for over 15 years, and other then the carrying case dry routing, this thing still works great.
@jster19636 жыл бұрын
Awesome, Thanks!
@sijessiejim696613 күн бұрын
how long does the gas last?
@RickRose7 жыл бұрын
Thanks Jster! I'm a noob at it, too. I bought a Victor kit and have just started playing around. Have fun and be safe.
@jster19637 жыл бұрын
Thank you my man! So far I love it but I realize it gets pretty hot! So def be careful......
@johnmorgan86286 жыл бұрын
Nice informative video I liked how you did everything in front of the camera set up to both tips
@TheChipmunk20086 жыл бұрын
Love the honesty of your video, linked in from another welding video. OxyAcetylene appeals for the portability.... for heating, like you said. I am not good at welding at all LOL
@jster19636 жыл бұрын
I'm a total novice, but I really enjoy learning. I hope to get the hang of this someday, And thank you so much......
@obfuscated30905 жыл бұрын
So PRACTICE systematically. Anyone can learn to weld, but STUDY the professionals and READ. The Oxwelder's Handbook, 1939 version preferred, was written at the peak of OA industrial welding at the beginning of the WWII era. Cheap online, totally worth it, you'll enjoy what you learn.
@MisterMitchMM6 жыл бұрын
Enjoyed watching your learning process. Thanks for sharing.
@Engineerboy1004 жыл бұрын
Very cool, I'm a newbee too, I used a torch like 35 years go when I was a diesel mechanic working my way through engineering school. Don't remember much. this was super fun to watch. I think I'll get a kit and watch a few more videos and relearn how to use the torch. Thanks for posting.
@jster19634 жыл бұрын
Thank you very much! I love tools and have wanted this for some time. I haven't used it since this video, but I have it for when I need it. Good luck.....
@sydneyshaw6781 Жыл бұрын
I appreciate these videos. I feel like this is what KZfaq should be about. No click bait. Just an honest review. Thank you again.
@jster1963 Жыл бұрын
Thank you so much! I appreciate the kind words…..
@mattpariset90687 жыл бұрын
Man i digg your laid back positive attitude about everything, thank you for the info about this rig im contemplating on getting it myself. They could have stepped their game up in the goggles department but otherwise seems like a decent setup for the everyday gearhead.
@jster19637 жыл бұрын
Matt Pariset It really is a great DIYer's rig. I've seen some HVAC guys use a similar torch in a store freezer. I just wanted something to heat a stuck bolt here and there. Or cut something small. This works for me. And thanks a million for the kind words......
@scottshepherd36684 жыл бұрын
Really like the way your videos are produced. You seem like a good dude. Keep up the good work!
@jster19634 жыл бұрын
Scott Shepherd WOW! Thank you very much for the kind words! I really appreciate that.....
@josephputnam29645 жыл бұрын
Wow, its cool to see my people on here. I'm from St Louis too! I was a fabricator/welder years ago. Anyway, its cool to see a local doing these videos. I am now a happy subscriber. :-)
@jster19635 жыл бұрын
Joseph Putnam Thank you so much! But I have a bit of bad news. I’m not from Saint Lewis. My family and I took a vacation there and we all got TShirts. If it helps we all loved it! We still talk about how great of a time we had. Thanks again and sorry......😬
@marcbenz61946 жыл бұрын
Thanks for the info, the viewer comments were helpful as well. BTW, we are also in St. Louis, South County. Glad to see a video from a local guy.
@jster19636 жыл бұрын
marc benz You’re welcome! But sorry no. I got that T-shirt on vacation in St. Louis. I live west of Chicago. And thank you!
@andreak0012 жыл бұрын
I bought this set to use for jewelry making. I'm done stting it up and getting ready to use it. Thanks for your informative video!
@jster19632 жыл бұрын
Awesome! I hope it works well for you. And thank you very much…..
@SHAKA387 жыл бұрын
Hey, I've always wanted to buy a set, but like yourself, I have no experience but a lot of needs. This gives me a boost of confidence that I could get the hang of it and not have to take work to a shop. I'll have to bump this up on my wishlist. Thanks!
@jster19637 жыл бұрын
SHAKA38 I've wanted one for a long time. It would have really helped a lot on my tractor restoration! I didn't want the big one because I won't use it that much. So this small one is perfect for me. I'm glad this helped. And thank you very much......
@jamescollins94836 жыл бұрын
Kick ass for doing it yourself I'm a machinist and welder and I'm impressed by your go get it attitude
@jster19635 жыл бұрын
Thank you very much! I don't know why I'm just seeing this comment. But thank you....
@rkeesee9165 жыл бұрын
Thanks for taking the time to put this up
@jster19635 жыл бұрын
Thank you for the kind words....
@stuffy3217 жыл бұрын
Great video! On my way to Harbor Freight right now to get one. Thanks for your post.
@jster19637 жыл бұрын
Awesome! And thank you very much! I hope you like yours as much as I like mine......
@silvereaglesessions2521 Жыл бұрын
Great video. Thanks for the in-depth review!
@jster1963 Жыл бұрын
Thank you very much!
@jhitt797 жыл бұрын
If you do any mechanical work on a regular basis, a torch is a must have! Once you get proficient at using it and learn to set your regulators (I'm sure you researched it) you'll wonder how you ever got by with out one.
@jster19637 жыл бұрын
I will def do research and try to get proficient! And thank you very much!
@RONNIEJNZN4 жыл бұрын
I consider myself pretty slick with a torch ( in an automotive garage capacity) but I also have an induction heater, no flame, which I personally think is also invaluable, especially around fuel tanks and cv and rack and pinion boots and nuts where you have to save/keep the bushing under it.
@ludirty7485 жыл бұрын
I'm in the same boat as you, great video, and great comments! Love to learn, plus I don't like depending on others. If nothing else, to know.
@jster19635 жыл бұрын
I hate depending on others, and thank you very much....
@justinforcier47503 жыл бұрын
Thanks for the video, and I’m glad you’re trying something new. From now on, please never use a torch against concrete. Concrete has moisture in it and if you heat it with a torch, it will explode.
@jster19633 жыл бұрын
Thanks for the tips!
@WColdblooded357W2 жыл бұрын
Thanks for that, I'm a scrapper and have been thinking about a torch for while
@jster19632 жыл бұрын
Thank you! I hope you like yours.....
@001desertrat36 жыл бұрын
I don't want to scare you, but what I'm about to tell you is Very Important - NEVER try to use an Acetylene bottle immediately after it has been laying on it's side. Acetylene bottles have a sponge like material inside the bottle, and the sponge is impregnated with ACETONE and the Acetylene Gas is absorbed by the Acetone. If an Acetylene bottle has been on it's side, remove the Regulator if attached, and crack open the Tank Valve to blow out any Acteone that may have gotten into the valve. - If you don't, as soon as Oxygen contacts Acetone (when you turn on your Torch) it will cause an EXPLOSION, and if you're not using Anti-Flashback Arrestors , it can flash all the way back into your Tanks. KABOOM ! - I'm a Union Certified Top Millwright / Certified Welder-Fabricator and I have actually seen that happen to an inexperienced person.
@jster19636 жыл бұрын
001DesertRat I've read that! I'm a cautious person and I researched oxy/acetylene and have seen that mentioned a lot! I'll be careful. And thank you very much......
@Aa-wv4gh6 жыл бұрын
Right , acetylene is 20% stable , it needs the acetone and internal membrane to make it safer. Use no oil around the oxy , my professor in college , who worked the ship yards in San Diego , ,lost a coworker to an oxy explosion because the torch he hooked up to use had a spider on the fitting , the oil in the spiders body set the oxy off.
@jster19636 жыл бұрын
YOWZA!! I appreciate the "heads up"! I will really be careful. And thanks again......
@Aa-wv4gh6 жыл бұрын
YW , you'll read on the oxy gauge 'use no oil " , and the dish soap you use to check for leaks , make sure it has no oil in it either.
@jayjowers55306 жыл бұрын
Do not open acetalen tank without regulater or kaboom
@RobbyNowell7 жыл бұрын
A good tool to have. I'm not a pro with the torch either, but it was the first thing I learned on in high school. I have a similar setup made by ESAB. I went with a small torch because I never need to do much past 1/4 inch, and usually much smaller gauge than that.
@jster19637 жыл бұрын
I wanted something small too. I don't do this for a living and will rarely need it, but it sure is cool when you do! And thank you very much Robby.......
@davidbuckner64544 жыл бұрын
Appreciate the honesty I learned to cut and weld in high school and ben thinking about buying one of these
@jster19634 жыл бұрын
I remember my father and his friends working on cars and using the torch to free broken bolts. I got it for that, but like that I can cut and weld with it. I don't know how to do that yet, but I'll learn. And thank you....
@colton5bucks3 ай бұрын
Love this for the fact that you're no pro and honest about it. Just learning like the rest of us
@jster19633 ай бұрын
Thank you so much!
@1970chevelle3967 жыл бұрын
I've had a torch since I was 17 years old. When I first started welding that's what I used. Now I only use it to heat stuff up. Had to have the regulators rebuilt a few years ago.
@jster19637 жыл бұрын
Sweet! I can't wait to try to weld for real. And thank you very much!
@1970chevelle3967 жыл бұрын
jster1963 I first started welding in high school metal shop class 28 years ago. Back then I only got to stick weld and gas weld. No mig or tig.
@williefufu29857 жыл бұрын
Man its hot. I like your positive energy and enthusiasm. Look like you are having fun with this.
@jster19637 жыл бұрын
Willie Fufu LOL! Yes, I'm having a ball. And thank you very much.....
@flatheadronsgarage73456 жыл бұрын
Same way I started learning. This will be a handy well used tool in your shop. 👍 I’ll add,, with my set when I’m through welding, once I shut off my tanks I’ll bleed the lines and back off the gauges so there is no psi and the diaphragm in the gauge won’t have any tension. They’ll last longer too.
@jster19636 жыл бұрын
Great advice! Thank you very much....
@arodandjeter14 жыл бұрын
5:42 way better flame. I’m sure you’ve found out by now but I usually set my acetylene around 7-8 then I slightly crack both oxygen and acetylene on the torch handle. When you light it you should be pretty close to the flame you need. The way you did it works but if you were ever near a wall or something nice you don’t wanna soot it up. Good video man!
@deaddogblue6 жыл бұрын
I enjoyed your video, do your research and be safe. Keep up the good work
@jster19636 жыл бұрын
Thank you so much! I'll do that. And thanks again......
@classicuniquegifts97045 жыл бұрын
I'm glad to see this video because I'm a bench jeweler and I have been looking for a good oxy acetylene setup for melting platinum. Thanks!
@jster19635 жыл бұрын
Alamo Armed Civilians I’m so glad it helped! Thank you and I hope it works well for you.....
@danielsmith24475 жыл бұрын
Cool review, I'm like you, I see something I don't really have a use for but want it. I then buy it and play with it and usually end up being pretty good at using it.
@jster19635 жыл бұрын
Awesome! I'm the same way. And thank you so much...…...
@da-one894 жыл бұрын
Thank you for the review.. helped a lot
@jster19634 жыл бұрын
Oscar Torres You’re very welcome! And thank you....
@impactajuvenile6 жыл бұрын
Take a class at your local community college, that’s what I did years ago. They’re fun and addictive! I ended up taking all of them, I can gas, mig, tig and arc weld now. Back then it was just around a $100.00 a semester and supply cards were like $10.00.
@jster19636 жыл бұрын
Great advice! And I would love to, but I just don't have the time. I plan to take some courses when I retire. And thank you very much.....
@N0body2476 жыл бұрын
Learning to weld now is about 5k for a nights course about 5 hours a night for about a thousand hours. Thats with certification for a job.. Personally... I would just call some welding companies and ask if someone can teach me.. maybe i buy pizza and beer.. every day i learn.. They get fed and i learn from actual guys doing it. No way your gonna spend 5k in food and beer learning.. after a month of complete hands on training with guys that live and breathe it.. your gonna be 100x better than any night course you can take. Just my opinion.
@rockyaev82873 жыл бұрын
Great review! Thanks for sharing
@jster19633 жыл бұрын
Thank you for the kind words......
@gmdeutsch3 жыл бұрын
Thanks, I’m on the same boat. I don’t need it, but want it and I can see how it can come in handy once I have it. Thanks for your video, it was very informative for a newbie welder like me.
@jster19633 жыл бұрын
Thank you! It's fun to have tools. I plan to use this when I restore my car. Thanks again....
@chaseanonymous93277 ай бұрын
Thanks for the video, this was helpful
@jster19637 ай бұрын
I’m so glad it helped! And thank you…..
@HemiRod237 жыл бұрын
If you become proficient at oxy/acetylene welding, it is a relatively easy transition to TIG welding. Out in farm country, they turned us loose in the metal shop with oxy/acetylene in 7th grade shop class. Pretty sure that doesn't happen anymore. Stay safe and have fun.
@jster19637 жыл бұрын
Thank you so much! We didn't have shop classes until 9th grade. I had wood, metal, and auto shop. I loved them all. I want to learn to TIG weld and was hoping this might help. Thanks again.....
@HemiRod237 жыл бұрын
I'm fairly local to you (Crystal Lake). Any time you want to try TIG welding, just let me know and I'll be glad to help.
@jster19637 жыл бұрын
You are the man! Thank you so much! You are a hop, skip, and jump away from me. I'm in St. Charles. I think I've made it up your way before in about 30-40 mins. Thanks again......
@obfuscated30906 жыл бұрын
You can weld thinner metal than most TIG machines will handle by using a torch. Torches were the only game in town for aircraft and similar work before TIG was invented. A good source of affordable torches is Ebay. (I collect, sell and rebuild OA equipment.) Check the Oxy Fuel threads on Weldingweb for a lot more information.
@urjnlegend6 жыл бұрын
Ob Fuscated I need a oxy acetylene kit for HVAC, can I get away with not using acetelyne some.way?
@danielcollins6106 Жыл бұрын
I bought mine for the same reason you did. Not that I needed it I just wanted to play with and minor jobs. I love it. I would highly recommend.
@jster1963 Жыл бұрын
Awesome. Me too, and thank you.....
@robertobrien47993 жыл бұрын
Great vid and channel!
@jster19633 жыл бұрын
Thank you so much for the kind words.....
@SuperXrunner7 жыл бұрын
GREAT video, thanks
@jster19637 жыл бұрын
Thank you very much!
@ktjwilliams7 жыл бұрын
Thx for sharing with us .... You'll get the hang of it in short order ....
@jster19637 жыл бұрын
Kevin Williams Thank you very much Kevin!
@shawnmrfixitlee64787 жыл бұрын
right on man Good purchase !!
@jster19637 жыл бұрын
Thank you Shawn!
@ThePonirsx2 жыл бұрын
Thank you for making that good video
@jster19632 жыл бұрын
Thank you very much…..
@SeanLeonDrumz6 жыл бұрын
Thanks for sharing!
@jster19636 жыл бұрын
SeanLeonDrums My pleasure! And thank you......
@ralphlopez33794 жыл бұрын
Love the fact that you are trying. I recently started welding with O.A. my self. Quick tip always clean the metal that you are about to weld. I mean really clean it sand it wire brush it what ever you need to do to get it clean. Keep burning my friend.
@jster19634 жыл бұрын
ralph lopez Excellent advice! And thank you very much.....
@tjf15315 жыл бұрын
Nice, i just mine and looking forward to seeing what I can do with it
@jster19635 жыл бұрын
I hope you love it! And thank you very much....
@TheToolReview7 жыл бұрын
Good Video! Once you get the hang of it I am sure you will find many uses. 👍
@jster19637 жыл бұрын
I bet! It seem like a cool little rig. And I bet your right on the uses! Thanks a lot........
@TheLittlered19616 жыл бұрын
Love your honesty. I had to laugh at the need for new looking bottles though. This setup is great for the small time hobbyist or a trades man that has to schlep the unit around. IE HVAC repair man. Also great if you only use it once or twice a year. Other than that, you need bigger bottles. If you keep practicing your welding, you will find a need for refills far more than you want. Second, that was not a neutral flame there. A neutral flame is longer and is on the verge of turning yellow. This allows the inert gases, water and CO2, to protect the surfaces from oxidizing. The flame you had was excellent for freeing stuck or rusted bolts. Keep up the great work and I did enjoy the video. Thumbs up.
@jster19636 жыл бұрын
True. True and true! I have a lot of learning to do. I will work on that neutral flame. And really, I will only use this once or twice in a year. I just think it's cool! And thank you so much.......
@themidnightcoalcompany82544 жыл бұрын
You should do reviews on everything as a greenhorn cuz I had no idea how to use a torch and your video is effing awesome
@jster19634 жыл бұрын
The Midnight Coal Company LOL! Thank you very much.....
@micahmacarthur62526 жыл бұрын
I bought the larger kit about 10 yrs ago, doesn't get much use, but the regulators and torch have held up well. Think you would be happier with bigger bottles.
@jster19636 жыл бұрын
I have no idea how much I will use this, but so far I've only used it in this video. I love that I will be able to free really stuck bolts. That's my real reason for buying it. I love that it has the ability to weld, even though I don't have the ability yet;-) And thank you very much......
@AK995816 жыл бұрын
Micah MacArthur That all depends on what you're gonna use it for. The portable setups will work but are definitely not the best if you plan to do a lot of bending or cutting steel, but they are perfect for lugging into attics when you need to braze copper lines for central air conditioners.
@royreynolds1086 жыл бұрын
I agree with both people. This kit is great for portability but the big bottles are needed for lots of work because of volume.
@mattdinelle58714 жыл бұрын
Great video!!!!!
@jster19634 жыл бұрын
matt dinelle Thank you very much!
@billconnelly48403 жыл бұрын
Thanks for sharing.
@jster19633 жыл бұрын
Thank you Sir!
@johngoold12185 жыл бұрын
Thanks for this.
@jster19635 жыл бұрын
You're welcome and thank you.....
@MartsGarage7 жыл бұрын
Handy little kit. When lighting, have just the acetylene on and turn it up until it stops smoking. Then increase the oxygen until you achieve the small cone you want. The torch is much too small for welding that thick stuff. You would need a much bigger nozzle and up the pressures to suit. You also want to get it set up so you are comfortable and able to really stare right into the weld puddle, and feed the rod in. In other words you need to get close up, which takes nerve when you are learning. Keep practicing. Gas welding is a very satisfying process if you can get it right. If someone close by can spend a half hour with you showing you the basics it would pay dividends. For heating things up for dismantling etc it will be very handy. Mart.
@jster19637 жыл бұрын
Thank you so much! I wish I had a mentor near that could spend a little time teaching me. Maybe someday. Those are great tips on the settings and I will give that a try next time. That set came with 0 or OO tips so I do know it's light duty. I just don't know what light duty is yet, but I'm sure I will learn. Thanks again Mart.......
@FueledByIronTeam4 жыл бұрын
Thank you for this video, gave me a great idea if this is worth the money or not. Thanks again
@jster19634 жыл бұрын
Thank you very much!
@garyrock23565 жыл бұрын
Oxy-Acetylene is great if you have a workshop and can get the big bottles and get a supplier to refill them, buying small bottles tends to cost a lot. If you are going to weld you will need flux on the end of your rod so the metal runs, get the welding area nice and hot first. Acetylene is there to burn the oxygen and keep it alight. The majority of heat derives form the oxygen, by upping the oxygen you up the heat. When it comes to costs there are other options on the market like plasma cutters and 3 in one machines. So you can weld and cut using electric.
@jster19635 жыл бұрын
I'm so sorry I just saw this. It went to my spam folder. And great info. Thanks......
@robertofernandez1651 Жыл бұрын
How much does it cost and how much does it last?
@mikec.91774 жыл бұрын
Run your acetylene pressure @ 7psi and oxygen 35 or 40 depending on the size of cutting tip and make sure you turn your bottles off when your finished. If you have problems with your regulators or torch you may have trouble finding parts for a H F set up. Be safe and have fun
@jster19634 жыл бұрын
Excellent info! And thank you very much.....
@nbooker75046 жыл бұрын
Not a bad first time. A quick tip when cutting slightly angel the flame in the direction your cutting and it will kept ur metal hot so you don't have to stop every few inches to heat it up to cut. Great video.
@jster19636 жыл бұрын
Excellent advice! Thank you very much...….
@alvinomelgoza28877 жыл бұрын
Great introduction sir.
@jster19637 жыл бұрын
Alvino Melgoza Thank you Sir!
@jimmypopp26954 жыл бұрын
excellent video!!
@jster19634 жыл бұрын
jimmy popp Thank you very much!
@kmtischer5 жыл бұрын
I have to agree with you. When I buy a torch I always look for pretty bottles.
@jster19635 жыл бұрын
LOL! I like new stuff to look NEW! And thank you very much.....
@001desertrat33 жыл бұрын
@Kdog -- I like pretty bottles ( 36-24-38 ) too . Lol .
@austinevans46259 ай бұрын
Wow as a 19 year old I know how to weld sorta but I was looking at buying this to cut some stuff off our flatbeds at work but didn’t know how to use it and this video was helpful
@jster19639 ай бұрын
Thank you so much! And good luck with yours....
@williefufu29857 жыл бұрын
Back watching again. I want one of these.
@jster19637 жыл бұрын
Willie Fufu Lol! They are cool....
@williefufu29857 жыл бұрын
Thank you.
@WideVisionMetalFab7 жыл бұрын
Good review. :)
@jster19637 жыл бұрын
Thank you Matt!
@LawnGardenFun7 жыл бұрын
Good review my friend.
@jster19637 жыл бұрын
Thank you Weasel!
@pookatim7 жыл бұрын
Nice little rig. You should have a fire extinguisher handy whenever you are using it. Hot metal can go flying all over the place and land anywhere. Of course you know not to have any flammable liquids around but even combustibles like cardboard, plastic or a waste basket can easily catch fire with the temperatures you produce. I've seen a few near disasters happen even to seasoned professionals. Enjoy your rig and keep your wits about you whenever you use or store it.
@jster19637 жыл бұрын
Pook Atim Thank you so much! Great tips! I try my best to be safe and I love it when someone sheds light on things I miss. I would hate to hurt myself with my hobby and have to miss work. I still need my real job, lol. Thanks again.....
@jerryolivares54123 жыл бұрын
Kick ass you being honest was the best thing about this video and yeah most men we buy tool we might not need then and there but we want it lol
@jster19633 жыл бұрын
Thank you very much!! My wife doesn’t understand tools, but my viewers do😬. Thanks again.....
@ryanmoss385 Жыл бұрын
I like your style. your like me, a big kid that likes to play with new stuff!
@jster1963 Жыл бұрын
Tru dat! And thank you very much.....
@johnmcdonnell61097 жыл бұрын
Keep on learning jster! Those oil be great sills or those growing boys you've got also.
@jster19637 жыл бұрын
LOL! Thank you very much......
@garychandler42966 жыл бұрын
I bought the torch, gauge set in the black carry box a while ago, ($50 back then), and renigged when I found out how much ox & actylene bottles would cost me. So I went back to angle grinders and such and this vid reminded me to sell the unused kit. How about $40? It all looks quite nice and sufficient according to my past years of cutting, welding, and brazing working for John Deere. No hoses or tanks; just the head kit aforementioned.
@jster19636 жыл бұрын
Gary Chandler It does cost a lot if you’re going to use it all the time. I’ll just use mine to heat a stuck nut or bolt. I’ve only used it in this video so far. So I will rarely use this. And I think that’s a great price for someone looking for a small rig. Thank you and good luck.....
@jonathanpihl64386 жыл бұрын
Safety tip- dont let the slag drop on the concrete or weld with the piece resting on the concrete. Work away from the bottles. Use gloves. Thanks for the review, I am an expert with oxy/fuel. Bad habits will cause serious injury and property damage. Take a course at the community college.
@jster19636 жыл бұрын
Jon Pihl Excellent tips! I would love to take a course at the local college, but I have too much on my plate right now. And thank you very much.....
@justinmcdonald33766 жыл бұрын
My left knee has plenty scars from slag hitting the floor & coming to a rest between the ground and my knee
@infonator14 жыл бұрын
That's cool how you just try new things. I did that with my e-bike build. I've used torchs for 30 years and then used Propylene which is hotter and last longer but you need the torch rig for that. But I'm thinking to use a plasma cutter instead. Their a little more harder to work with but all you need is the plasma cutter with a air compressor. No gas needed.
@jster19634 жыл бұрын
Thank you. I like trying new projects. Someday I hope to get a plasma cutter. Thanks again....
@mmcnew13 жыл бұрын
I don’t know anything about any of this but was just looking at a Lincoln Port A Torch on OfferUp. This looks identical to the Lincoln except it’s red. The Lincoln is black. Currently the Lincoln is actually a little cheaper at Lowes. Weird, thats for sure. Great vid, thanks!
@jster19633 жыл бұрын
Thank you! And good luck....
@Mike-012344 жыл бұрын
I took classes at local community collage to learn how to weld it was well worth it. The instructors were master welders had a lifetime of experience. This was way back in the 90's when no KZfaq, but even though we have that now It's still best to get good instruction on how to use these. We had a week of safety class before we were even allowed to touch a welder. Gas welders are dangerous the flame can reach 6000F not to mention your working with explosive gases. The college had all kinds of donated equipment we could use once we got checked out.
@jster19634 жыл бұрын
blastman8888 I would love to take a class on welding and I might have time when I retire. Great advice! And thank you very much.....
@klv4004 жыл бұрын
Thanks.
@jster19634 жыл бұрын
You're welcome...
@baggd657 жыл бұрын
Right on. You will get the hang of it.
@jster19637 жыл бұрын
I hope so, and thank you very much!
@royreynolds1087 жыл бұрын
Just remember to NEVER set the acetylene to 15 psi or above. Watch where the flame and sparks are going to prevent fires(been there done that). Good torching.
@jster19637 жыл бұрын
Thank you Roy! I will take heed to the safety tip. I'm not a fan of unplanned fires. Thanks again.....
@marzsit98336 жыл бұрын
15psi is the warning pressure, the actual explosive pressure is 29psi.
@j.r.43895 жыл бұрын
Great job. Good info. I haven't read any comments, so I don't know if anyone else has told you... Although I've never tried it myself, but I'm 99.9% sure that butter cant cut anything. But it sure is good on biscuits or pancakes or waffles. All jokes aside, I'm like you, when I see an interesting tool that I've never used, I just have to get it & invent a project to use it on. In fact, I tell everyone when we go to a supercenter, keep me away from the tool isles or I'll end up with a mortgage. & shoes... keep me away from the shoe isles too. Hah.
@jster19635 жыл бұрын
J. R. LOL!! I was wondering where that was going! And thank you very much.....
@rogeroconnor51827 жыл бұрын
i have used a torch most of my life,i would get a good pair of flip up goggles and even a tinted face shield. i would bet its the same set home cheapo sells as lincoln for alot more
@jster19637 жыл бұрын
Great tips! I can't wait to try to really weld. And thank you very much.....
@rogeroconnor51827 жыл бұрын
i have watched some of your lathe videos and some of the allis chalmers. i have a craftsman 109 lathe and a collection of old garden tractors,i have videos of some of the stuff i am working on
@jster19637 жыл бұрын
I'll take a look.....
@AK995816 жыл бұрын
roger oconnor The HF torch is not the same as the one from Home Depot/Lowes. The "Lincoln Electric" torch kits are made by Harris, and I'm pretty certain the tips are not interchangeable with the HF kit. I think the HF kit does take Victor tips though.
@obfuscated30906 жыл бұрын
I strongly agree. We use light tinted Jackson face shields for torch work and they are very comfortable. I use a hard hat mounted shield because it's more comfortable than the headband style and because sparks and spatter bounce. Wear clear goggles beneath your face shield. Goggles alone don't protect your face, and shields alone are inferior eye protection.
@Legenddjt3 жыл бұрын
Good video bro
@jster19633 жыл бұрын
Thank you very much!
@THEMECHANICOCMissionViejo7 жыл бұрын
Good stuff.
@jster19637 жыл бұрын
The Mechanic OC Thank you very much!
@kpoolove7 жыл бұрын
Yay, it's like sparklers 😊
@jster19637 жыл бұрын
You're such a girl! LOL. Thanks Kpoo......
@koreywilliams45703 жыл бұрын
I'm looking into getting one because I need a way to cut 1/2 Inch plate and 1/4 Inch plate. All I have for metal cutting at the moment is my angle grinder and my chop saw.
@jster19633 жыл бұрын
I’ve cut 1/4” with it but not 1/2”. It should be able to do that. I don’t know how much gas it uses either. Try to check with someone that cuts plates with oxy/acetylene and see if it will work for you. Good luck and thank you.....
@nothankyou55245 жыл бұрын
Nicely done, though.
@TheLittlered19616 жыл бұрын
I forgot something I was taught this 40 plus years ago. Looking at that setup I don't know if it will work. I was using the standard setup for oxy Acetylene. My oxy bottle was 90 cubic feet. This is still relatively small to the big bottles. The big thing is the hook up for the Acetylene. It should have a left handed male thread end on it. If the hose setup is just like mine, I have a big surprise for you. In stead of getting the Acetylene tank refilled, you can hook that up to your BBQ propane tank. Why is this important? It is much cheaper to get that filled than the Acetylene tank filled and will last longer. 2 down sides. Not as cute as your tank and heavier to move around. Second, propane does not burn as hot. Propane does burn hot enough to do most jobs though.
@haroldcrabtree48996 жыл бұрын
propane will work only for brazzing and not welding,for cutting you have to have a differant jet in the tourch
@jster19636 жыл бұрын
Awesome! And thank you very much.....
@justinmcdonald33766 жыл бұрын
Propane burns at 1900 degrees. It will melt some metals, although not near as well as acetylene.
@braytonwillerval39423 жыл бұрын
When you’re cutting use a quarter turn fuel and a half turn oxygen. I’m a ship fitter so I cut with torch’s on 2in plus steel all the time and when I use that it cuts smooth, my pressure usually stays at 40-80 oxygen depending on thickness and 20 propane. But acetylene heats up faster so you probably need less
@jster19633 жыл бұрын
Great info! I learn from people helping like you. People that are experts. So thank you very much.....
@northwestoutdoors7693 Жыл бұрын
Acetylene run it about 5 to 7 psi oxygen run it about 20 to 25 been a welder for well over 10 years and those setting always worked for me.
@jster1963 Жыл бұрын
Excellent! Thank you very much…..
@truckinforever9857 жыл бұрын
Are the tanks stamped with the appropriate numbers to swap them out at the gas supplier
@pierresgarage26877 жыл бұрын
Hi Jster, You'll love what this can do, maybe less when it comes time to refill... $$$$ lol As for pressure, you can normally set acetylene from 5 to 7 pounds, and oxygen from 15 to 25 pounds, probably around 20 in your case it should cover it all... Good safety item to get are sparks arresters or those one-way valves to help with reverse flow in the hoses... mostly if one of the tank gets low and you didn't pay attention. Never let the acetylene go under 40 psi or oxygen may eventually get into the acetylene tank, you know the rest... Cutting with those is very costly, it's using lots of oxygen... Have fun and watch your frills at the bottom of your fancy jeans, I remember putting off the fire on a couple of guys legs... :) Also, make certain that your insurance company covers welding equipment, I had to deal with that issue myself... Cheers, Pierre
@jster19637 жыл бұрын
Insurance company and welding equipment?? That never crossed my mind. I may want to store it in my shed until I find out. THANK YOU! Also, I can see where this can cause things like my pants to catch on fire. I will def be careful. Great tips on the bottle pressures. Once again I never thought of back feeding 02 into the acetylene. That could be BAD! Thanks again Pierre........
@pierresgarage26877 жыл бұрын
Be safe and enjoy... !!!
@gorila19586 жыл бұрын
Pierre's Garage How long do these bottles last before they have to be refilled ??