Hardie Plank Install Guide

Рет қаралды 346,216

MHE Martin Home Exteriors

14 жыл бұрын

Jacksonville Fl Hardie plank Installation guide, colorplus

Пікірлер: 34

@KG5RK 6 жыл бұрын

I wish I had seen this video a month ago. More importantly, I wish MY CONTRACTOR had seen it too ! Very informative. Thank you.

@g.e.boroush5176 2 жыл бұрын

This was an excellent presentation. Clear, thorough, and I thoroughly enjoyed it. Thank you!

@Anthony-fi9ml 5 жыл бұрын

Ok I was about to go off about flashing at but joints until the update at the end lol. Well done. I am going to DIY this myself. I’ve read all of the manufacturer information and watched hours on hours of videos.

@edbrackin 3 жыл бұрын

Me too until I saw your reply.

@incarnadinelifestyle 4 жыл бұрын

I wish you all worked in Arizona. You appear to be THE experts in siding projects.

@puzer1 2 жыл бұрын

...brilliant...this guy just punctured the seal on perfectly good siding above what he was replacing to "test it"...put down the hammer, Sparky...

@MiguelOjedaJr 8 жыл бұрын

Good video!

@huejanus5505 2 жыл бұрын

You do a lot of damage to the ‘good wood’ when testing. Do you smack the hammer claws into all the siding on the house?

@craigsbuyer2270 Жыл бұрын

No lie, saw that after hitting it with the hammer, he will need to replace it now 🤦🤦🤦

@Mike-pj1kv 4 жыл бұрын

Great info.

@GumbootZone 12 жыл бұрын

Thanks for the "update" at the end. It matches all the other installation guides I've seen. My friend sided his new house in coloured Hardi planks and left a whole 1/8 inch gap at EVERY join, with a square of black tar paper behind join. Upon questioning, he told me the gap had to be there for "expansion". The black gap lines now show up quite badly. He might have to go around and fill each gap with pre-coloured special order caulking. I'm a little frustrated at whoever gave him that advice.

@Ithinkimaybealesbian 6 жыл бұрын

Gumboot Zone caulk all the butt joints

@SheilaMaoMao 3 жыл бұрын

Martin, just like to confirm with you: so we can add hardie plane on top of existing t111 plywood wood siding plus moisture barrier? We don’t need to add furri strips for circulation first? My current exterior wood panel is 5/8 plywood so far. I like to add extra layer of fire proofing material, hardie is my choose. Correct? Help, help, thanks.

@jnunez1203 6 жыл бұрын

Great vid..needs more likes

@SuperQdaddy 19 күн бұрын

Why not use trex wood on bottom..doesnt rot ?

@swagger911 7 жыл бұрын

Anything specific about the plywood you used to replace the rotten siding down along the bottom? Thickness, type, etc..

@jnunez1203 6 жыл бұрын

Russel Caldera its called plywoid siding..the thickness you have to match it to yoir needs theres different thickness..measure the one you got and just match it with the one you buy

@jamespotter4878 6 жыл бұрын

If you went around my house beating all the good wood with a hammer I would be PISSED!

@jayc4715 5 жыл бұрын

Be like.." Hey bro WTF ARE YOU DOING!?

@ATXTube 5 жыл бұрын

Relax I'm a limo driver

@ericcrea6837 5 жыл бұрын

No shit. This is good siding except for where I just beat the hell out of it.

@belkenator 5 жыл бұрын

He could beat the wood even faster if somebody was there to hold his caulk.

@MrGoatman07 4 жыл бұрын

It's ok, I've been educated by KZfaq. 🤪

@keliandjaz 7 жыл бұрын

Is it ok to go right over the t1-11 like you did on this video? I'm getting ready to do this to my house I would love to hire the pros but I only have enough for the material but I think I can lol

@arquichurches1497 7 жыл бұрын

Jaz &

@pamgober901 5 жыл бұрын

The research I've done, suggests that slip sheets be used behind all butt joints, not just caulking alone, due to shrinkage, and the inability to properly re-caulk and re-paint these areas. very unsightly from the examples I've seen.

@cengeb 3 жыл бұрын

Ya don't caulk the butt joints, never, follow Hardie instructions, they have fine details to follow. And all cut ends must be painted with the Hardie paint kit, and there is special caulking that matches hardie color Plus paint