Sandisk Extreme Portable SSD 1TB USB C common failures

Рет қаралды 21,281

10 ай бұрын

Sandisk Extreme Portable SSD 1TB USB C common failures
for data recovery call: 855.366.4232
or request your service here: www.hddrecovery.ca/contact-us/
Data recovery tools: www.acelab.eu.com
Data recovery software: www.r-tt.com/?JGKHD000
Our solution helps to resolve issues with data access on Sandisk Extreme Portable V1 and V2 drives in over 80% by following this method.
Here is the list of drives that we have actively been recovering with this PMIC reballing technique:
SDSSDE61-500G-G25 500GB
SDSSDE81-1T00-G25 1TB
SDSSDE81-2T00-G25 2TB
SDSSDE61-2T00-G25 2TB
SDSSDE61-1T00-G25 1TB
SDSSDE61-4T00-G25 4TB
SDSSDE81-4T00-G25 4TB
If you lost your data on Sandisk Extreme Portable SSD - do not hesitate to reach out to us
simply fill out this form: www.hddrecovery.ca/contact-us/
Our address is
HDD Recovery Services
391 Bank St, Suite 201
Ottawa, ON
K2P 1Y3
Canada
Updated 2020 my gear for soldering:
I record all my videos using this HDMI Switcher: amzn.to/31LCsq6
Green inspection light amzn.to/2DFJoYu
Platter extractor: bit.ly/2YhQD2y
Momentary foot pedal switch amzn.to/2OSqjZF
Vacuum pump amzn.to/364XWxa
Cleanroom wipes: amzn.to/2ZLj49G
Programmer amzn.to/2DRjL7a
Quick pogo pin adapter for eepROM amzn.to/33TYVyO
Microscope: amzn.to/2rqWcwr
Vacuum chip pickup tool: amzn.to/2tNCSxc
Multimeter: amzn.to/2EHKAxO
USB volt/amp monitor: amzn.to/3CqLRmc
Microscope camera 21mp 60fps 1080P: amzn.to/2Rb5cUq
JBC precision soldering iron and tweezers: amzn.to/33MACm8
Hot air station: amzn.to/2K7Mztk
Infrared preheater: amzn.to/2rYCH1c
Fiberglass scratch pen: amzn.to/3uHIGUp
Flux dispenser: amzn.to/2spLw4D
BEST Flux: amzn.to/2mXJd1b
Wick: amzn.to/2mNr0Xh
Solder: amzn.to/2mtyC0a
Solder paste for BGA reballing: amzn.to/2LrKQCi
NAND BGA rebelling stencil amzn.to/33Oq9a5
Gloves: amzn.to/2mbHWDI
Fume Extractor (mine is no longer available but this is the new version of the same unit) : amzn.to/2mNCmL7
Gear for filming:
small camera: amzn.to/2mNw51T
big camera: amzn.to/2Ficg9o
Lens on big camera:amzn.to/2Cx3fGw
this video: kzfaq.info/get/bejne/aMt7jKVnx7iyZ58.html

Пікірлер: 130

@ErikCrowKrahe 2 ай бұрын

Got this for my girlfriend’s mom as she’s a photographer. She was editing two weddings off of them and it wouldn’t show up on her mac anywhere. She would’ve had to start completely over but before I broke down the ssd I tried the R-Studio software he recommended. Immediately upon starting up the software the drive showed up and all the files were fine. Thank you!

@DiskTuna 10 ай бұрын

Niceeeee you did the experiment with reballing same PMIC!! And yes, that looked amazing!

@hddrecoveryservices 10 ай бұрын

Thank you

@jaydub1147 10 ай бұрын

The work you do is always amazing! Thank you for sharing! Big fan of your channel.

@hddrecoveryservices 10 ай бұрын

Thank you very much!

@mariahezra 10 ай бұрын

I've been searching for a video like this for MONTHS!!! I just sent in a request - fingers crossed you can help me! 🤞🏼 Appreciate the upload!

@hddrecoveryservices 9 ай бұрын

Mariah, I replied to your email. Thank you.

@gurhanbayr5080 10 ай бұрын

Erkin my friend this was again a nice job. regards from istanbul

@computerworksuk 10 ай бұрын

Brilliant work as usual.

@hddrecoveryservices 10 ай бұрын

Hopefully this video will help many to get their data back. I literally have over 70 of these SSDs sent in by now

@paultomlinson528 10 ай бұрын

Outstanding work! Nice explanation too, very good work

@hddrecoveryservices 10 ай бұрын

glad to share the knowledge. Use it for your next job bro

@paultomlinson528 10 ай бұрын

@@hddrecoveryservices you are a Saint sir!

@fxoverfianl5046 10 ай бұрын

brilliant as always...

@Withnail1969 3 ай бұрын

Just bought a 4tb one and I must say it's reaslly well made. Nice and solid.

@clockworkphoto 10 ай бұрын

been waiting for this video,

@hddrecoveryservices 10 ай бұрын

Good things come to those who wait 😜

@sporknife123 10 ай бұрын

Thanks for this video, I was able to fix one today by just reflowing the power IC, didn't even need to remove it. :)

@hddrecoveryservices 10 ай бұрын

That's awesome

@Multilink4441 10 ай бұрын

love these guys!

@hddrecoveryservices 10 ай бұрын

Thanks 👍

@mikefievet5284 10 ай бұрын

Perfect job! You rocks!

@hddrecoveryservices 10 ай бұрын

I appreciate it

@MkmeOrg 10 ай бұрын

Very cool recovery. My fingers are crossed :)

@hddrecoveryservices 10 ай бұрын

Thanks, we are still working on it

@MkmeOrg 10 ай бұрын

@@hddrecoveryservices Thanks very much

@tenmillionvolts 10 ай бұрын

Another great recovery. We haven't seen any platter drive repairs for a while. Any head stack replacements coming up?

@hddrecoveryservices 10 ай бұрын

I will be working on those. I have 2.6TB of hard drive footage over the years :)

@codamyer 10 ай бұрын

Great job Erkin! Now your just showing off. :) LOL You make it look way easier than it really is. Jerry L

@hddrecoveryservices 10 ай бұрын

Thank you Jerry!

@EH4-EH4 8 ай бұрын

Wow !! your skill is truly amazing. 😀👑 Just watched my Sandisk ultra 3D ssd 500gb disappear in front of my eyes ! Drive letter just disappeared from windows file explorer, i tryed everything to get it back nothing worked !. So i had another Sandisk ultra 2 240gb plugs it in to my laptop w10 same thing happened !! Now this is just my opinion 2 drives dying at the same time the odds must be huge. Keep up the good work . cheers !🥂 liked and Subscribed

@orange11squares 2 ай бұрын

don't buy these drives, just make your own external SSD using an M/2 ssd and a SSD enclosure for M.2 nvme.

@suryavanshib 10 ай бұрын

Awesome ✌🏻✌🏻✌🏻

@dogcowdogcow 10 ай бұрын

Do the non-eutectic solders still have problems with thermal cycling? So many devices - MacBook GPUs, xbox 360 rrod, etc - have had consistent problems that usually go away when reballed with SnPb

@geg_ant 8 ай бұрын

Oh my god Man, you gave me some hope, I got SanDisk Extreme 1Tb full of family video and pictures that unexpectedly just stop working, doesn't show up in the system at all. Local company that I requested for a quote for recovery sounded about 900$ not even looking at it. I did some electronics myself in the past, and decided to take a look, opened it up and pulled out NVME, inserted it directly into M2 on MB and got no luck. Couldn't find any specs on chips, so decided to throw it in the drawer for some time (for 6 month). Seems like the time has come, thanks to your video, I got some option to try, will get a donor (WD NVME SN750 has the same components as well as Power Management IC) it costs 40$, hopefully that would be the fix. Don't want to go NAND de-solder and dump route (don't have tools for it)

@hddrecoveryservices 8 ай бұрын

DM me on instagram. I have new PMICs. Pulling them can easily damage the chip, so new ones are the best option @hddrecovery

@geg_ant 8 ай бұрын

@@hddrecoveryservices sent, thanks!

@geg_ant 8 ай бұрын

@hddrecoveryservices got no response from you, even on email. Well, if you don't have them or can't sell, why would you offer and then ignore....🙁

@geg_ant 6 ай бұрын

@hddrecoveryservices So I got all the data from mine, there is a long story to it. But in short words, I just reheated PM IC with hot air, and it started working good enough to get the data

@WordupG 4 ай бұрын

@@geg_ant Thanks for posting this reply. After watching this video it was my conclusion to try the same thing. So glad to hear it could potentially work!

@codierenadelsdorf4961 6 ай бұрын

Can any tell my what is the part right cs print on board .. part is missing on my board

@steveng5503 10 ай бұрын

Yep… very good. 👍🏻✌🏻🇬🇧

@verpejas 9 ай бұрын

Hi! I would like to ask you, does the SN770/SN570 also suffer from this issue? I myself have a revised 2tb version of the SN570 (with the same nand and controller as SN770) and it works very well for me - low temperatures with great performance. Unfortunately i can see that most WD drives use the same PCB design and now i started to worry about potentially loosing my data someday

@pickelsvonbrine 10 ай бұрын

What clamp/vise are you using? I am in the search of a new one.

@inothome 10 ай бұрын

Great fix, as always. When was the last time you did an HDD recovery? Seems like forever since you posted a video of one. What do you like better, the old HDD or all the newer SSD recoveries?

@hddrecoveryservices 10 ай бұрын

I just don't have my recording equipment at the shop anymore. But I work drives at least 3 times a week when I am there. On hard drives I don't work alone, most of these tasks are now on staff. I like hard drives more to be honest.

@inothome 10 ай бұрын

@@hddrecoveryservices Ahh ok. So still plenty of HDD recovery going on, cool.

@codierenadelsdorf4961 6 ай бұрын

On the nvme smd part brown whit point. Witch part is This ? On my board is missing right cs print on board Please help 😢

@LindonSlaght 5 ай бұрын

I have the non extreme consumer 1tb variant, do I have anything to be worried about?

@ronlevin2339 10 ай бұрын

what will happens if you try to remove the IC without dealing with all the underfill around it ? You can rewove all other small components as well ? Can I remove this underfill with some organic solvents ? acetone,CHCl3 ? DMF ?? DMAC ?

@circuitsable 10 ай бұрын

nice job, entertaining as always :) forgive my ignorance, why not just reball the IC with a soldering iron and solder?

@hddrecoveryservices 10 ай бұрын

Soldering iron does not create perfect balls.

@igorrabinov653 10 ай бұрын

it is faster become a gay, then reball this ic only with iron

@jewhunterbiden 10 ай бұрын

@@igorrabinov653 more true words have never been spoken, last week it took me almost 8 hours to become homosexual

@redangrybird7564 10 ай бұрын

Components are getting more tiny all the time. My uncle was an electronics repairman and he used to work on radios and tvs with vaccum tubes inside. 😮👍

@hddrecoveryservices 10 ай бұрын

As long as there is a microscope the size of components is not that important :) but yeah they do get tiny sometimes

@WordupG 3 ай бұрын

Would it be possible to bypass the power circuit by soldering leads and injecting the correct voltage to all the places where said voltage should be found around the power management chip?

@hddrecoveryservices 3 ай бұрын

I think so

@awdrifter3394 7 ай бұрын

It's always these unleaded solder that keeps causing issues. Imagine all the Xbox 360, laptop with Nvidia GPUs, and now SanDisk SSDs that are junked due to these unleaded solder breaking. It probably caused more environmental damage than if we kept using leaded solders.

@dominickmarciano8217 9 ай бұрын

I don't do data recovery but I do work with microchips and I was wondering a good way to learn how to solder surface mounted components? I've always stuck with DIP/through hole because I know I can't solder anything else. I have to imagine there is a better way to learn soldering other components which don't include buying a bunch of ICs and destroying them in the process; some kit or something?

@hddrecoveryservices 9 ай бұрын

Stencils for chips and different pitches, good paste, hot air station (which you can literally get for like 300$ these days for a good unit that a lot of pros use) curved tweezer, paper towels - is all you need. Practice and practice. There is so much content to learn from my channel included

@maxgood42 8 ай бұрын

This is like the iPhone 6 all over again , under-fill removal and re-balling the chip.

@emanuelmilani7976 10 ай бұрын

This is the same unit for the "Western Digital is facing a class action lawsuit regarding SanDisk Extreme Pro SSD failures and subsequent losses of user data"?

@hddrecoveryservices 10 ай бұрын

Yep

@fixthetempo7276 10 ай бұрын

hehe, good job. As an former iphone repair master i did the same thing at least 2000-3000 times :D no joke)))) слегка угрел , маленькие шары повылезали в трех местах

@hddrecoveryservices 10 ай бұрын

Угу, они всегда у меня лезут на них :)

@Ben79k 10 ай бұрын

When you repair a device like this for data extraction, do you return the patient drive to the customer? Or just the Data. I assume often times it is not reccomended to use the repaired device.

@hddrecoveryservices 10 ай бұрын

Data gets cloned and put on a new drive. Never trust a failed device :)

@Ben79k 10 ай бұрын

@@hddrecoveryservices yes of course! I was curious if you return the patient drive to the customer along with this advice, or do you keep it for disposal

@danielemalagoli2751 3 ай бұрын

Hi Erkin, in your opinion, is it possible to fix the glue issue under the pmic by just using Ultrasonic cleaner?

@hddrecoveryservices 3 ай бұрын

I think it's a broken contact. ultrasonic will break it even more

@Wisecrackerist 10 ай бұрын

Can you use a solvent to disolve the underfill? It would make the process easier and wont need to spend time repairing the soldermaks

@hddrecoveryservices 10 ай бұрын

If it can take the underfill, I guess it will take the soldermask too :)

@desertdatarecovery 10 ай бұрын

There are a few chemicals you can use that will not remove the solder mask. Takes about a week, but it works.

@jewhunterbiden 10 ай бұрын

it depends, you need to know the material of the underfill, material of the chassis and the soldermask to find a solvent thats not conflicting. but i suppose with some trial and error this should be possible

@horaciobalestrini696 5 ай бұрын

Hi, I have sdssd61-t100 and suddenly it becomes unreadable... I was copying some files and the device freezed, and after that could not access it. What can I do to recover my unit and data? Thank you!!

@hddrecoveryservices 5 ай бұрын

send it to us

@AB-sg1vd 10 ай бұрын

Please, could you clear up some doubts for me: What is the difference between PC-3000 portable and the PC-3000 UDMA? Both work with HD, SSD, SD card and pendrive? Do they both do the same thing? Thank you very much.

@hddrecoveryservices 10 ай бұрын

UDMA is a single channel PCIe card. Good for entry level. Portable 3 is top of the link set that can be expanded into NVMe and SAS support. Portable can also work as a standalone imager. Best to reach Acelab sales. They will do a much better job explaining the difference

@AB-sg1vd 10 ай бұрын

@@hddrecoveryservices , Thank you here from Brazil

@AfricanBeard 4 ай бұрын

You guys taking orders?

@storyteller_ua Ай бұрын

Hi! Have same problem with my SDSSDE61-1T00-G25 1TB. Help needed.

@hddrecoveryservices Ай бұрын

No issues, request your service here www.hddrecovery.ca/contact-us

@tristankordek 10 ай бұрын

😎👍

@ArkanElric 10 ай бұрын

I just sent one this week to a Data recovery company. But I thought the problem was with the V2 version only, mine is first gen 1to and no firmware update available. My model is SDSSDE61-1T00. Is it the same one in this video?

@hddrecoveryservices 10 ай бұрын

Most likely

@ArkanElric 9 ай бұрын

@@hddrecoveryservices So turns out the controller of my Sandisk is "damaged". The analysis shows the presence of a dynamic XOR protection on the NAND component (which works), but data cannot be read because of the XOR protection, as the controler contains the key to go through the protection of the dynamic XOR (if I understood correctly). Have you had ever encountered a thing like that? And do you think that putting a new controller would resolve the issue? Or put the memory chips to a clean SSD motherboard. I don't live in Canada anymore but I wish I could send you my SSD...

@graealex 10 ай бұрын

Today we had a discussion on Reddit, mostly about it being crap, because you can't even issue a Secure Erase command via USB.

@hddrecoveryservices 10 ай бұрын

Can you drop a link to it here?

@graealex 10 ай бұрын

@@hddrecoveryservices It's German, but you know how to use Google Translate: r/de_EDV/comments/16vdm56/externe_ssd_sandisk_extreme_portable_1_tb_sicher/

@GiovanniBausC 8 ай бұрын

I have a slightly older 550 MB/s 1 TB model SDSSDE60-1T00-G25. Can anyone confirm if this is also affected by excessive failure rates or if that affects only the newer E61 / E81 generation?

@suryavishwanath8564 7 ай бұрын

only the newer ones..buts its good idea you take every data inside it and create a backup of it, as long the drive still functions

@GiovanniBausC 7 ай бұрын

@@suryavishwanath8564 Thank you! 👍

@alexxmoralex 10 ай бұрын

is not better if you move the NAND chip to a donor SSD?

@hddrecoveryservices 10 ай бұрын

No. It will not work for this device. My guess is that since they use their own locking system when security feature for vault is on, data is tied to the controller. I tried NAND swap to a donor before, and it does not work on these

@wizardbd 10 ай бұрын

hello good day I love watching your videos from Bangladesh. Scandix External Portable SSD One TB USB Common Failures. I learned a lot from this video. Below you hav 0:33 e given a data recovery link, but in our less developed country, we don't have the ability to buy recovery software with so much money, especially in my case, what can I do, please tell me.

@hddrecoveryservices 10 ай бұрын

Maybe local DR services would be cheaper?

@F3RC4O 10 ай бұрын

Can you recover a microsd with raw format? Help pls

@hddrecoveryservices 10 ай бұрын

Yep

@F3RC4O 9 ай бұрын

@@hddrecoveryservices What would it cost? Could you give me more information? I sent a message to their page, but have not received a response. Thank you

@baghdadiabdellatif1581 10 ай бұрын

Great work 👌 What if you just reflow the ic ?

@cutemartinj 10 ай бұрын

You can't with the underfill there

@hddrecoveryservices 10 ай бұрын

Yeah underfill is not gonna let the chip resettle

@baghdadiabdellatif1581 10 ай бұрын

@@hddrecoveryservices it's all ready resettle. Try to put same weight on it 😜

@Alan_Skywalker 10 ай бұрын

Your stencil is exactly the same as mine.

@hddrecoveryservices 10 ай бұрын

That's a good stencil, saved me a bunch of time 😄

@OldePhart 10 ай бұрын

This flaw reminds me of the red ring of death for the XBOX.

@Ualik123 10 ай бұрын

what is that fancy screwdriver with holes?

@hddrecoveryservices 10 ай бұрын

You want one? DM me your address on Instagram

@hardroch1000 10 ай бұрын

use decapon paint remouver to desolve the shet

@cognetic 10 ай бұрын

For the algo!

@hddrecoveryservices 10 ай бұрын

Brian, you are the best ;)

@jabirt.k6096 10 ай бұрын

How much cost for this recovery?

@hddrecoveryservices 10 ай бұрын

700$

@oladojabankole9672 7 ай бұрын

Hello.. Why are there so many Fake SSDs ? Is there anyone regulating this production?

@igorrabinov653 10 ай бұрын

when ic is off, yo can change the alloy( pb 183, or 138) so it will be easier to get off the underfill from the board. cell phone tecnitian hack

@hddrecoveryservices 10 ай бұрын

On the board I am guessing? Yeah, I think it's more due to improper scrapers. There is a j blade I would usually use but I didn't find it during the filming. I would add PB type to pads regardless

@igorrabinov653 10 ай бұрын

@@hddrecoveryservices actually both. have to be more gentle to ic, do not drag the tin on its surface. when you reduce the melting point You will be able to work more smoothly with the scrappers. the pads do not make you stuck because of lead free alloy is still solid, then you use 250°c to clean underfill .also can use wick, carries away a lot of underfill, and no need to scrap too much

@sp_live 10 ай бұрын

This Video Same Nvme SanDisk Ssd Please Share Estimate

@kolossarthas 10 ай бұрын

sandisk dropped the ball on these units. the replacement models fails as well. these are famous on NAScompares channel

@hddrecoveryservices 10 ай бұрын

they did, but I thank them for it :)

@fabiomuzzi7047 10 ай бұрын

Nice job. But if I had such power issued I'd probably have powered it from an external supply with the right voltages instead of removing that glued chip.

@hddrecoveryservices 10 ай бұрын

Please explain how you would do that

@fabiomuzzi7047 10 ай бұрын

@@hddrecoveryservices I'm not a data recovery expert, only a sysadmin with the hobby of electronics. You need two different supply voltages (please forgive me if I don't remember what these are: 3 and 1,3 volts if I remember correctly). If this is what you need, and you know where these supply voltages must be applied (because you tested a working device) then with a lab power supply (with 2 outputs) you could simply generate these voltages and apply them to the right points (that are the traces that come from the power chip output and go to all the components that need them). Since the power supply chip is probably disconnected somehow, I won't expect it to create any issue with this power coming in from its output. And if it does, isn't it easier to just remove it instead of replacing it? Well, probably for me it's easier because I'm not as good as you at reworking SMD components.