Hemera install guide for CR-10S Pro / CR-10 Max
Рет қаралды 55,758
Күн бұрынThe Hemera (formerly Hermes) is a new all in one extruder/stepper/hot end by E3d. Building on my Ender 3 guide, I’m now fitting this permanently to the CR-10 Max (also compatible with CR-10S Pro).
The Hemera in isolation is a beautifully engineered piece of kit and will thrive on a printer designed for it from the ground up. On this printer, it’s a much better fit, especially when paired with a volcano hot end and large nozzle set.
My mount aims to act as a spacer so that the Hemera bolts into the metal carriage. Two holes need to be drilled using it as a template. This is designed for the volcano hot end, the regular V6 may not reach.
More info on the engineering: e3d-online.com/blog/2019/11/2...
Thanks to all of those in the community who have designed parts for this kit.
Purchase the Hemera (please check voltage and filament diameter options):
E3D: e3d-online.com/e3d-hemera-175...
Amazon: amzn.to/2tGiyh8
Tiny machines: bit.ly/39kSRCC
Phaser FPV (Aus): www.phaserfpv.com.au/collecti...
Previous Hemera guide for Ender 3: • Hemera to Ender 3 - Co...
01:08 Brief overview of Hemera
02:03 TH3D solid bed mounts: www.th3dstudio.com/product/th...
02:28 Step 1: Swap to E3D Volcano hot end
E3D guide for this: e3d-online.dozuki.com/Guide/U...
Volcano nozzle dot reference: e3d-online.com/brass-nozzles-...
03:37 Step 2: Wiring
Example of compatible part cooling fan: amzn.to/2GKBYF9
05:20 Step 3: Designing and print mounting parts:
My custom mounting parts for CR-10 Max/CR-10S Pro: www.thingiverse.com/thing:414...
5015 blower fan duct by Hangtight (duct mount plate and volcano duct parts): www.thingiverse.com/thing:404...
Alloy carriage replacement by Portzal: www.thingiverse.com/thing:409...
07:12 Step 4: Physical install
11:49 Step 5: Firmware
InsanityAutomation Creality Marlin 2.0 branch: github.com/InsanityAutomation...
My configuration.h: pastebin.com/Qb29ayVH
CR-10S Pro / CR-10 Max firmware update guide: • How to update CR-10S P...
Pronterface: www.pronterface.com
13:51 Step 6: Calibration
Pronterface download: www.pronterface.com/index.htm...
Set e-steps reference: marlinfw.org/docs/gcode/M092.html
PID autotune reference: marlinfw.org/docs/gcode/M303.html
More detailed video on PID autotune: • Two easy fixes for 3D ...
E3D VREF setting: e3d-online.dozuki.com/Guide/0...
More detailed video on setting VREF for the Ender 3: • TMC2100 guide - Steppe...
More detailed video on E-steps calibration: • How to tune your slice...
16:43 Test prints
20mm calibration cube: www.thingiverse.com/thing:214260
Baby manticore: www.myminifactory.com/object/...
Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: www.x3d.com.au
Take a look around and if you like what you see, please subscribe.
Support me on Patreon: / teachingtech
@TeachingTech 4 жыл бұрын
A public apology to David from Insanity Automation, as at one point in the video I incorrectly said Automated Insanity. Some tips for firmware from Tiny Machines: -Force10SPro and Force CRX display does not need to be on for the 10S Pro or Max. Those toggles are for 32 bit boards. -When you select MAX or 10S PRO V2 it forces BL Touch, bilinear and 25 point probing since those machines come from the factory with BL Touch. When customers purchase our BL Touch kit for the 10S Pro, we have them plug the Z end stop into Z+ and use V2 firmware. -If you're getting false positives on the runout sensor, you may have issues with your sensor/ wiring. We use the default values without this issue and setting it higher will result in a later trigger on a real event.
@S_Hofmann 4 жыл бұрын
I flashed the screen now and it was exactly what he had as a result.
@Tommy43087 3 жыл бұрын
Would the firmware modification you posted be the same for the CR10S Pro v2? Such as the probe offset? Also would I need to change the y -axis stop 10mm like the MAx? Any help is appreciated, thanks! Also, the M851 X-40 Y0 is the only coordinate change needed for the BL touch?
@greliusz 3 жыл бұрын
@Tommy S YES!! Pls @Teaching Tech how for CR 10 S Pro V2 - i have Hemera but Firmware im a noob.
@YoutubeHandlesSuckBalls 3 жыл бұрын
Followed this step by step and discovered that on Windows 10 at least, extra to these instructions, initially you need to install the driver (FTDI) from the supplied SD card (which you mention in your other firmware video), then in Device Manager you need to set the baudrate of COM4 (at least that is what it was on my machine, your mileage may vary) to 115,200 to be able to connect and have the printer show in Arduino. Once I made all the changes and could see my CR10s Pro V2 in Arduino, the firmware did not compile for me on Arduino 1.8.13 (C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc.exe: The filename or extension is too long), did compile on 1.8.15 but then would not upload. This did however allow me to export the compiled binary, which I then uploaded with Cura. It is important to note that Arduino outputs two files, one with the bootloader and one without. If you want to keep your bootloader, use the file that says 'with bootloader'. If you don't, you can't program it via USB again because you will have no bootloader... Aside from this small detour into the frustrating world of standard computer issues, the video is a very good guide to setting up and installing a Hemera on your CR10s Pro/Max.
@dukeezra5015 2 жыл бұрын
I know it is kinda off topic but does anyone know of a good website to watch new tv shows online?
@MegaJameslaw 4 жыл бұрын
Thanks mate! Ur vids are fantastic, ur a born teacher
@MegaJameslaw 4 жыл бұрын
absolutly fantastic mate!
@PJC3DP 4 жыл бұрын
Great video! very tidy and innovative installation. I have been getting some great string free results with 0.6mm retraction @ 20mm/s for PLA+.
@TeachingTech 4 жыл бұрын
Thanks Patrick, I'll try that setting.
@eliseoteson 4 жыл бұрын
Thanks A lot! Really Helpful!! Best wishes from Colombia.
@nicholascrow7405 4 жыл бұрын
Dude, your shirt game has been on point lately!
@avejst 4 жыл бұрын
Nice upgrade Thanks for sharing👍😀
@patnodus 3 жыл бұрын
This video was a life saver, Thanks!!!!
@b00sted_mx59 4 жыл бұрын
for the ender 3 i found you can use the normal t nuts for the y extrusion so you can slide the rail front to back and gain back the lost y travel. Normally there are holes and just scres into threads into the extrusion. Might have to drill out the threads but i used m3 bolts insted of m4 so it just fit through them since it was all i had.
@MakerFarmNL 4 жыл бұрын
You have developed into the most extreme content generating 3D printer youtuber on the interweb!
@deadsimpleali5540 4 жыл бұрын
Very useful video as usual. I'm planning to install it on Cr10S Pro. Loved the minimalist style base plate. Have modified it for stock Hemera e3d hotend with space to mount filament run out sensor. Will post it on thingiverse in a day or two.
@driedekker 4 жыл бұрын
have you done it and if so how did you get the firmware to compile.
@ImaginationToForm 4 жыл бұрын
Great install. I'd like this on my CR10S Pro but I'm not up to wanting to do all this work at the moment. And meh back to the Creality fan? I took the time to upgrade to Noctua fans. Though now it's my Mars Pro that sounds like a jet plane.
@SuperYellowsubmarin 4 жыл бұрын
Exactly what I need for my CR10MAX !
@Smitty3572 4 жыл бұрын
Looking to do this for my Ender 5 soon. Trying to get as much benefits available before I make the step.
@christopherNadarajah 3 жыл бұрын
i feel smarter doing this, lol waiting for the filament sensor video as well. thanks for this video!
@nearswisky 4 жыл бұрын
thank you I just received mine today
@janikhen7736 4 жыл бұрын
I have an hemera extruder attached to my ender 3 with a custom allumium x-carriage wich actually was pretty easy to make with a handsaw and a drill. With this Solution i loose hardly any buildvolume and it is actually almost as compact and even stirdier than the stock assembly. So i cant reelly agree with you that this upgrade would not make that much sense on an e3 because I got far better and more reliable printing results than before. But still your videos are great and have helped me often enough.
@TeachingTech 4 жыл бұрын
The Hemera is a quality piece of gear, what I'm referring to is it's price vs the printer itself and the loss of build volume on a moderate sized printer. Your install sounds very tidy.
@AvanSuti 4 жыл бұрын
Awesome vid as always. Sad that you didn't read my message on fb, i would have so loved to remodel my mount for the hemera (ender5) to fit your needs.
@markh2005 4 жыл бұрын
Great T shirt! 👍
@evilstuie82 Жыл бұрын
Hi Michael, thanks for a great video. I'm brand new to 3 d printing so I've been enjoying the learning curve as I work my way up to printing ABS dash panels for my KITT project. A couple of issues I ran into with the build. Firstly the V2 Fan duct doesn't seem to sit in the right place, however I'm not sure what the optimal spot for this is so can't be sure. Also I printed all of the mount and parts in standard PLA and the fan mount bracket seems to have warped considerably once I screwed everything in. Lastly there's a few updates that might be worth mentioning for newcomers like me. I've added them in the next comment for what I found was needed, or different from when you made the video. For anyone attempting this, these are the things I found were required or useful: 1. Watch the Ender3 video first, as there's a couple of key things to pick up on. 2. Print all the required 3d parts first, and in a good solid material. I used PLA but PETG or ABS may have better luck in rigidity and shape. 3. The latest Marlin Creality DWIN branch does not have the touchscreen files in the same place/zip. They are now in the TM3D_Combined480272_Landscape_V7 zip. It took me a few goes of the wrong files to figure this out. 4. When you update to this firmware you lose one of the more important adjust features, which is the ability to adjust bed and nozzle temperatures at the start or mid print. 5. The Arduino build take s a significant time to compile and also has a couple of errors when compiling, but it did seem to work in the end. Took about 5 minutes sitting on the same screen before anything happened. 5. Many of the screw lengths suggested did not work for me, and I found that they were bottoming out on the hemera, or not long enough to catch the nuts on the other side. I used the next size up in length for most of the mounts, and either filed them down slightly or used washers as spacers. The fan duct mount needs to have the adjustable screw holes opened up a bit with a file or Dremel to allow the screws to slide up and down for adjustments. 6. Lastly the latest version of the Marlin firmware has 2 values you need to adjust for the bed size. There's BED_SIZE AND MAX_POS from 470 to 450. If you only adjust the bed size the x axis will crash into the right side.
@evilstuie82 Жыл бұрын
Edit, ignore point 4, the temperatures can be adjusted by just pressing on the commanded value which is slightly greyer/darker than the current value. Couple of updates on my setup also: Make sure you pick the right duct, I hastenly picked Duct_V2 because its the latest version, but that's for the V6 not Volcano. I've also found there is a remix of the blower mount that uses 3 screws instead of 2 and is much better aligned. Make sure you put the thermal paste on the heatbreak going into the hemera, and screw the heatbreak in correctly and test the thread heights for it at the correct positioning of the hotend prior to connecting anything. Once assembled you cannot readjust these without taking the whole thing apart. I ended up putting connectors on everything so I could easily remove the unit when needed for jams/clogging. Lastly, no-one seems to agree on settings for this setup in order to get good prints, particularly with PLA. I am having inconsistent (thin/thick/none) lines as well as gaps at the start and excess at the ends of each layer, despite the retraction settings. If anyone has a good set for these it would be appreciated.
@stevesloan6775 4 жыл бұрын
Rock solid tutorial. Keen to do this conversation on my X1 Sidewinder🤜🏼🤛🏼🤓🇦🇺🍀🍀🍀
@Lucas_sGarage 4 жыл бұрын
I think that is not necesary
@macswanton9622 4 жыл бұрын
This is the most impressive setup I've ever seen. I wonder if its equal will be available as a stock model..? In my lifetime?
@GunGryphon 4 жыл бұрын
Another thing I noticed, if the thermal compound in the Hemera heatbreak threads is too thin or otherwise comprised, you will get intermittent heat creep issues. It can appear to print beautifully for several minutes, then it will begin to underextrude and jam. If you pull the jammed filament out, clip it, and reinsert it, it will print great for another time period just to repeat the process. To avoid this make sure your thermal compound is very well applied, the difference is night and day.
@MeAgainstMusic 4 жыл бұрын
Hi @Teaching Tech - do you think your Template for the X-Carriage can also be used for the ender3 to mount the Hemera on the original X-Carriage?
@patrickmaartense7772 4 жыл бұрын
great guide ! can this work for a CR10 S5 with Supervulcano ? Im still looking for a good DD system to use
@oleurgast730 4 жыл бұрын
Just a little "magic" in the video: In the end there suddenly is a silicone sock on the volcano, but it wasn't added in the video before... The moment you add the silicone sock is relevant, as it changes the PID you need. So if using silicone sock, add it before doing PID tuning.
@TeachingTech 4 жыл бұрын
You are correct. Got the footage of the silicone sock going back on after the hot tighten but left it out by accident.
@adriaangreyling4943 4 жыл бұрын
Hi Mike! Would you be able to share your tension and retraction settings for your Hemera? More specifically for TPU?
@PeterHelenefors 2 жыл бұрын
THANK YOU 🙏
@GunGryphon 4 жыл бұрын
Be very careful when pushing your x carriage onto the T-slot aluminum. If your wheels are tight, or there's a bur, the edge can gouge the wheel, catching a little each time it rolls past.
@elnurmehdiyev5062 4 жыл бұрын
Hi, excellent tutorial by the way, I'm looking to upgrade my CR-10 MAX too, but one question: why you did not simply design and print adaptor to fit original extruder and filament sensor right next to the original hotend? wouldn't that be easier not to tweak firmware? I understand volcano hot end would give you higher extrusion rate, but if I don't need it, I'm happy with slow printing, can I simply reposition original extruder to the short distance from original hotend without tweaking firmware?
@AllTheNamesWereInUse 4 жыл бұрын
Please keep wearing these types of shirts. thank you :)
@pattihyer8931 Жыл бұрын
Thank you, I took your advice about the CR10S Pro V2 years back and watched you channel consistently. I purchased the Hemera and looked at your install video. The back plate and BLtouch mount are still on Thingiverse but not tiny machines or many of the others. Most disturbing is that the git hub file no longer has the Dwin file to edit. That and I am unable to find any reference on the things in the firmware that need to be changed. I also too your recommendation to purchase Simplify 3D.
@OldCurmudgeon3DP 4 жыл бұрын
If memory serves the hemera stepper is closer to a pancake. It just has mounting blocks on each end that make it look like a full size. Bet you can drop the "vref" on it 100mA or so since it's a geared drive.
@TeachingTech 4 жыл бұрын
You're totally right, it's just a pain to flip this big girl over to access the electronics.
@tasmedic 3 жыл бұрын
Hi MIchael Thanks for a great video. I was right with this and have followed along almost to the end, upgrading my own printer. However, I don't get the part about the filament runout sensor. I gather the stock one isn't used as I see a bit of filament stuck in it to prevent an error occurring. Does the setup as shown here include filament runout sensing? If so, how does it work?? You do say in the video that you tested the filament runout protection. How did you do that? Then I'm further confused that you're discussing re mounting the stock filament runout sensor. Do you still need it?!! Thanks. Chris.
@chrzacho 4 жыл бұрын
Great videos ... To what degree does this guide apply to the CR10s Pro V2? I don't have any problem on the hardware side, my concerns is the firmware. Can I use TM firmware (ver 2.x) or do i have to revert back to stock firmware?
@Lucas_sGarage 4 жыл бұрын
Michael, i want to Buy a tevo tarantula pro, do You recomended?
@aedanyalda6453 2 жыл бұрын
Hi mate great work I’m currently doing the upgrade on my cr10s pro v2 and following your video however the mounting plate is only for the volcano block not the standard that comes with the hemera kit I discovered that after all the hard work and put it in together, would you kindly upload a mounting plate for the stock block thanks in advance mate keep up the great work
@Ronaaronhunt 2 жыл бұрын
Same here 😞
@DanielTorres-bs8dx 3 жыл бұрын
Can you PLEASE PLEASE PLEASE do a detailed install video, just like this one, for the BondTech DDX for the CR10s Pro??? I want to purchase the DDX but scared on the firmware install. Lol.
@brandonjaimes3011 4 жыл бұрын
I just got the Direct drive kit from printer mods (it's 100 dollars cheaper) and I love it
@TeachingTech 4 жыл бұрын
Had the original version and now the 1.2 on My Ender 3 for a long time and I love it.
@digaum 4 жыл бұрын
Hi Michael. Quick question: Where did you find those Dupont connectors for sale here in Australia? Thanks.
@3dprintingbird554 4 жыл бұрын
Any plans for the Micro Swiss Drop in Direct Drive?
@rorysunderland7690 4 жыл бұрын
Filament runout is a must have for this large format printer, a follow up video would be appreciated if you figure that out
@paullancefield 3 жыл бұрын
Very easy to do, you just need some electrical cable so you can extend the cable and bolt the sensor where you need it. Either, replace the existing cable, crimping on appropriate connectors or, more “hacky” but easy to do if you don’t have the crimping tools and terminals, splice in a cable extension using heat shrink cable connectors. The only tools needed then is a knife and a lighter.
@megaobi 4 жыл бұрын
Omg. Thank you so much for sharing this there is no decent video guides for hemera especially for cr10s pro. I bought one last week its been 3 days spent whole weekend trying to get it going as i am noob and have no idea about firmware. Can i follow the firmware part for me my cr10s pro. I have v1. Thank you so much again best video and content. Love your work
@danbrown586 4 жыл бұрын
The firmware changes for the CR-10S Pro should be the same, except that you'd choose that printer in Configuration.h rather than the CR10 Max.
@megaobi 4 жыл бұрын
@@danbrown586 thanks for your reply.
@chrzacho 4 жыл бұрын
@@danbrown586 Hey .. I hope that applys for the CR-10s Pro v2 aswell!!!
@stogie1027 2 жыл бұрын
I got a really good deal on a cr-10v2 as my first printer. I wounded if this would be a good fit for it
@superwakky2947 3 жыл бұрын
would this also work for the cr10s pro v2?
@natewallis1 4 жыл бұрын
I am thinking of getting the CR10-S PRO V2 from Banggood. I am quite technical, but a newbie in the 3D printing world. are there any recommended upgrades that you would make from the get go that will make my life easier? It looks like this extruder upgrade might be one of them.
@brettmcconnell8040 3 жыл бұрын
do you have a video of compiling InsanityAutomation /Marlin 2.0 as i would love to add it to my Creality CR-X eg 10S Max and Pro
@justinguerrera8322 4 жыл бұрын
any chance of you doing a quick version of this for the CR-10 V2 ? I got that printer to do bigger prints and the hot end cant really keep up. Im a noob at this stuff as well
@safarityler 3 жыл бұрын
Same boat here
@kaliboeshoots 2 жыл бұрын
Where can I find the stl for the cable management part from in the video please
@driedekker 4 жыл бұрын
Any chance of a firmware file for the 10s pro v2 with bl touch and hemera as I can not get the ide to compile it on my machine.
@MrSmith336 4 жыл бұрын
Thanks for the installation review. Nice shirt too. Do you have one for Niki?
@TeachingTech 4 жыл бұрын
They didn't have any Niki ones at the last GP I attended, but if the chance comes up I'll swoop.
@gianmarcofavero1967 3 жыл бұрын
Good evening Teaching Tech. Need a great help. I have a Cr10s Pro V1 with the hemera direct extruder mounted, I wanted to understand if it is possible to install the bltouch v3.1 (antclabs), and update the screen with the black theme of the v2. Can I safely install Marlin 2.0? Thank you very much. UPDATE: I managed to do everything and I also put the black theme. only thing: sometimes the bltouch when I turn on the printer, it flashes, others don't. Unfortunately with the fan (5015) at 100% I did various tests (PID tune) but with the heating cartridge (30 Watt), the hotend (volcano) cannot heat to the desired temperature. on the one hand it is good, it means that the fan cools a lot. Maybe I should put the original cartridge (40w)? or a silicone sock? thanks.
@DrTriggered 4 жыл бұрын
I want to attempt this with my "CR10S Pro", but in the Configure.h where you have to define it has a side note that you have to solder r64 and r66? Basically scaring me from even taking this project on. I need to modify the firmware as well, im using the "hero Duct and able" attachment and need to change my probe offset as its probing off the bed and jamming the nozzle into the heated bed. Not sure if you've covered this in another video already.
@digaum 4 жыл бұрын
Same printer here. If soldering is involved, then things get a bit more complicated and risky. Let me know if you manage to find this out. I'll start doing some reading as well. Thanks
@3DPrintedProps 4 жыл бұрын
Awesome vid as aways. I really need someone to do a video for the Formbot Raptor 2.
@nicwilson58 3 жыл бұрын
As you compiled firmware anyway, can I ask why you used M851 instead of putting those offsets into the source code?
@MrBrettStar 4 жыл бұрын
I’ve noticed with the volcano it is almost impossible to change without dismantling everything. Would an xt30 connector be ok on the heater cable near the heater? It would make it a lot easier but I’m not sure how much the heat travels up the cable, if it is too hot what would be a good alternative connector?
@MrBrettStar 4 жыл бұрын
Sorry I’m referring to changing the heat block
@wesleyphillips1489 4 жыл бұрын
Hey can get the firmware to upload from computer to printer any help you can give would be great as I know have a printer I can't use anymore. Thanks
@Hanzi2u 2 жыл бұрын
do you have a link for the cable chain ? as i can see i need it myself. thanks in advance
@RCMlll 3 жыл бұрын
Is 400 the factory e-step value for alll CR10Max printers?
@Impecable.. 3 жыл бұрын
Do a Hemera install for the Artillery Sidewinder x1!
@Audio_Simon 2 жыл бұрын
Hi Michael does your Hemera mounting plate work with the V1 CR10S Pro? I'm thinking you probably have the V2.
@haitianboy420 3 жыл бұрын
I need a setup for the ender 3 max :(
@The_Engineering_Experience 11 ай бұрын
Has anyone done this upgrade with the Hemera Revo? I am wondering if the mount or the BL touch work with the foot print. the upgrade looks a bit smaller and I think it will work but figured I would check. Thank you for any information.
@The_Engineering_Experience 11 ай бұрын
Never mind it is shorter by 11 mm and lighter by 92g for anyone also wanting to know.
@amatris1996 2 жыл бұрын
Hi i cant get the Desuuuu firmware to work with my BL touch, Stock MB on my Cr10s Pro (V1) can you possibly help?
@nicholasgenzman4213 4 жыл бұрын
For the firmware idk of you did it but you didn’t show it but after you do a firmware update you should reset the eprom and after you reset save it by using the m500
@TeachingTech 4 жыл бұрын
M500 saves all of your current settings, which means an M502 to restore settings from the firmware would overwrite all of the calibration you just did.
@nearswisky 4 жыл бұрын
can you redesign that plate for a v6 hotend please?????
@mjethier 2 жыл бұрын
Do you still use this printer with this combination of print heads? I have had one since before this video and I never finished assembling it. The bed from the factory is pretty warped and I wasn't sure if it was worth upgrading to a hiwin linear rail system. What do you think about upgrading that unit to linear rails? Or am I just better off buying the other printer I saw you assembling a few episodes ago?
@Netherlands031 4 жыл бұрын
Why do you have to calibrate extrusion? According to e3d the e-steps should be 409. What's more likely, that e3d has it wrong or that you measured wrong with your ruler?
@kylelongstaff 2 жыл бұрын
Pls E3D Hemera vs Microswiss Direct Drive. I know Microswiss is easier to install and setup but is the E3D Hemera really worth it?
@ush2177 4 жыл бұрын
Hi will we see a seckit go update video soon with the new board?.
@TeachingTech 4 жыл бұрын
Not the new board yet, but the next video is on another upgrade for this printer.
@ush2177 4 жыл бұрын
Teaching Tech looking forward to it.
@greliusz 3 жыл бұрын
I have a problem. I am stuck in the Marlin setting, I can not complicate the Arduino program and I do not want to upload to the CR10S Pro V2, because it gives me errors. I am doing something wrong, I did it more precisely step by step, I selected Mega or mega 2560. Or maybe otherwise, would you give a hex ready for the CR10S Pro V2? I have Hemera installed, but without the firmware, I die.
@LordCipher92 3 жыл бұрын
Why wont my CR10S pro V2 connect to pronterface and when I run out of filament the sensor pauses the print, but it will not start again
@Naifoza 4 жыл бұрын
hello, did you use the direct kit or bowden kit ? thhanks.
@Naifoza 4 жыл бұрын
for the cr10 max
@almirantecarvalho 4 жыл бұрын
First of all, awesome video as usual. One question: is the tinymachines firmware Marlin 2.0?
@danbrown586 4 жыл бұрын
Yes, the linked branch is based on Marlin 2.0.
@almirantecarvalho 4 жыл бұрын
@@danbrown586 thank you for the answer. I was confused because I thought Marlin 2.0 could only be edited on Vscode
@danbrown586 4 жыл бұрын
@@almirantecarvalho That's only the case when you're compiling it for a 32-bit board. You *can* use VSCode/PlatformIO to build it for the 8-bit board in the CR-10S Pro/CR-10 Max, but you don't need to--you can still use the Arduino IDE if you prefer.
@almirantecarvalho 4 жыл бұрын
@@danbrown586 Thank you again!
@Gunham20 4 жыл бұрын
Is it not possible to make a mount that has no loss in build volume for the more popular cr-10 / ender 3? 😭
@TeachingTech 4 жыл бұрын
The build volume for this printer is rated as 450 x 450mm, yet the bed and travel is more like 470 x 470. So we do actually lose a fraction but since there was spare to begin with it's ok. Ender 3 doesn't have this luxury.
@3lohssvrm 4 жыл бұрын
Ive done it, its not trivial. the whole thing needed to be mounted lower on the existing carriage and made an metal extension. i had the mount the bottom roller bolt the opposite way so the nut is on the back for more clearance. but then needed to cut slots in the x gantry brackets to clear the nut.
@pippaengroda 4 жыл бұрын
@@TeachingTech I have done this. I made my own custom aluminium carriage plate to mount the hemera and the BL-touch. i also moved the y-axis endstopp slightly. im able to reach the entire 235x235 bed. edit: I have a ender 3 pro.
@luker9921 4 жыл бұрын
Commissions ?
@colinjones9291 3 жыл бұрын
Ok, I am 2+ hours in to trying to figure this out. I have a CR-10S Pro V2 and am about to do this upgrade but cannot get firmware to compile, and even if I could, I am not confident that it's all configured to work properly. Anyone willing to help? if just a hex file for my CR-10S Pro V2 with the changes from the video would be super helpful!
@MartelKombat 4 жыл бұрын
Nice vid, just one correction. I think you only need to uncomment HotendE3D and E3DHemera. The rest will be defined later automatically. But right now I'm unsure because I don't have my folder with my changes files with me. Also, I think you need to change the defined thermistor. But let me check that.
@MartelKombat 4 жыл бұрын
Ok, you only don't need to uncomment DirectDrive. And with that you dont need to change the defined thermistor. The only thing that wold add to the video would be to check the NOZZLE_TO_PROBE_OFFSET with your Mount.
@colinjones9291 3 жыл бұрын
I am having a hell of a time with getting this firmware right. I have a brand new CR-10S Pro V2 and did the Hermera and Volcano upgrade. It is running creality's 1.70.0 firmware currently and when I try and do your steps exactly, I get all sorts of compiling errors. Any help would be SUPER appreciated! If so, let me know the easiest way to chat with you!
@JackWilson327 3 жыл бұрын
I don't suppose you got this sorted did you? Since this was posted I think some the key words / syntax in Marlin have changed. I'm about to start over this morning with the current config files from Marlin & my best guesses based on this, antclabs for the BL-Touch (also out of date), and a couple other sources.
@colinjones9291 3 жыл бұрын
@@JackWilson327 I did get this up and running with the latest marlin. It seems the new marlin is programmed much cleaner and therefor very little was needed to do. You will need to use ardiuno ide which is ardiuno 2.0 (still in beta). After that, couple modifications to the marlin. Io as shown in teaching techs "hemera install guide for cr-10s pro /cr-10 max". Hope that helps!
@JackWilson327 3 жыл бұрын
@@colinjones9291 Do you recall if you started with the configuration.h & configuration_adv.h from Marlin on github @ "MarlinFirmware/Configurations/config/examples/Creality/CR-10S/CrealityV1/" ? Asking because Teaching Tech says to use the example config from InsanityAutomation's repo and they seem to have defaulted back to the Marlin configurations and I'm either blind or unable to find any example configurations under their repo at this time. So @Teaching Tech is a little behind on this video now.
@JackWilson327 3 жыл бұрын
Never mind, I think I got it figured out.
@S_Hofmann 4 жыл бұрын
I don`t understand where I can get the screen files that fit Marlin-CrealityDwin_2.0. I have got almost everything running by now accept for those files. Could you please put a link in the description.
@S_Hofmann 4 жыл бұрын
@@ChazmillsADLT So. I just took this one. It is a different branch called Creality_DWINTest. I just flashed the screen files in there and it worked for me. Additionally, I want to say that with 3d printers half of the time I have no idea of what I am doing so be careful! ;) github.com/InsanityAutomation/Marlin/tree/Creality_DWINTest
@S_Hofmann 4 жыл бұрын
@@ChazmillsADLT I just realized that there is a zip called ,,SingleExtruderScreens_V2Rev1.1´´. I guess that the branch was updated.
@stecross5631 2 жыл бұрын
ok first the video is great but actually doing it nightmare plus compiling the firmware is not happening they erros just keep on coming i have tried going threw it manually and undefining then tried copy and paste for the config h file u provide and nothing a hex file for this would be great also i have the cr 10 s pro induction sensor and the v2 bltouch also the max and but there is a updated screen for the pro as the screen does not work in marlin on my pro the v2 i have not tried yet. Any firmware in hex format would be nice for all pro inductive sensor the bl touch version and max would make life alot easier
@perrykappetein9685 3 жыл бұрын
Hi, will the printed guide for drilling the holes also for the CR10s Pro V2 ?
@JackWilson327 3 жыл бұрын
I suspect you've got this answered by now ... I have a later (April 2020) V1 that was being sold at the same time as the V2 and the carriage is the same as my March/April 2019 V1. When looking at replacement parts at Tiny Machines the carriage sold for V1 & V2 is the same. So, yes, it should be the same. I've printed several different adapters & they all fit both my carriage plates. Never say never but you should be okay.
@perrykappetein9685 3 жыл бұрын
@@JackWilson327 Actually found this one www.thingiverse.com/thing:4775572 and works great. no drilling needed
@JackWilson327 3 жыл бұрын
@@perrykappetein9685 I printed that one. Yeah it fit nicely. I didn't want to mess with moving the break detector & there were a couple of things I didn't like about that one so I made my own. Once I get done testing I'll post it for the heck of it. How did you handle the configuration.h file? Did you use the one off the Marlin configuration repo?
@JackWilson327 3 жыл бұрын
Actually, never mind. Sorry! I think I found the right file. I was getting completely confused because I was trying to fork the repo and that process was not giving me the right configuration.h. It is there in the repo and if you go get the zip of the repo under releases the right one appears to be there as well. - github.com/InsanityAutomation/Marlin/releases/tag/CrealityDW73
@perrykappetein9685 3 жыл бұрын
@@JackWilson327 I am using Nic's Firmware. facebook.com/groups/485185272196044 Nic's Creality 3D Printer Firmware & 3D Printing Support
@Chaot92xD 3 жыл бұрын
Hi Guys, Can someone help me, please? I am not so experienced with the arduino software.. and i have a fault messagec while i try to compllier that firmware its called : C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino/main.cpp:43: undefined reference to `setup' C:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino/main.cpp:46: undefined reference to `loop' collect2.exe: error: ld returned 1 exit status Because of this fault i can't finish it ... I open that marlin.ino and change like he did it in configuration.h nothing more ...
@megaobi 4 жыл бұрын
PLEASE NOTE: The custom Hemera mount is not suitable if you are running v6 hot end on the Hemera! it is noted in thingiverse but I missed it - now stuck with no printer - just the heads up to others!
@anthonyciofalo7005 4 жыл бұрын
I just did the same thing...
@madmax1419 4 жыл бұрын
Do you remember 911, the crashing Twin Towers? Ok, this is something the whole world will never forget. But why I‘m talking about? Because of heat and the behavior of steel. Why is this interesting for 3D printing? When steel gets warmer and warmer it looses it‘s strength. When it‘s at 500°C it has loose 50% of it‘s strength. At 1600°C it melts. You just need 1/3 of it‘s temperature range to loose 50% of strength. Now we have a look at our hotend. It‘s mostly made of aluminium. Aluminium melts at 600°C. When I compare it to steel, our 200°C at 3D printing will cost the alu hotend 50% of it‘s strength. Printing PETG at 235°C or PACF at 250°C will make the hotend weak. A collusion with anything (for example at sequential print)at this temperature can cause a break of the M6 in the hotend. This happened more than 2 times at my sidewinder ( Volcano) After thinking about temperature and strength of aluminium I decided to use brass or copper instead of Aluminium. After this change I had no issues any more.
@haley8004 4 жыл бұрын
I like you but god I dread your intro music
@jon9947 4 жыл бұрын
So I dont jump to any conclusions, you bought 100% of everything featured in this video? I just have a hard time believing you bought everything in this video unless you specifically tell me you did. I really dont understand why it is so hard to start off your videos telling us what you got for free and what you paid for if your opinions truly are your own and you have nothing to hide.
@coreymac2381 4 жыл бұрын
Jon He is not reviewing the products. He is only showing how he installed them. I can see where one who hasn’t followed Michael for some time might think his reviews could be biased if he got the products for free. I trust Michael to give an honest review regardless of how he got it. He has given unfavorable reviews to products he received for free. In his review for the CR 10 Max, he discloses that the printer was provided free of charge by Creality for review. I don’t expect anyone to disclose where they bought every part when they are showing me how to do something.
@jianghengyi632 2 жыл бұрын
Hi Michael, how did you deal with the filament run out sensor. tks!
Liqui-Dirt 3D
Рет қаралды 76 М.